lkml.org 
[lkml]   [2021]   [Nov]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v2 2/2] irqchip: Add Qualcomm MPM controller driver
On Fri, Nov 26, 2021 at 07:19:07PM +0000, Marc Zyngier wrote:
> [resending after having sorted my email config...]
>
> Hi Shawn,

Hi Marc,

Thanks for all these review comments!

>
> On Fri, 26 Nov 2021 09:35:29 +0000,
> Shawn Guo <shawn.guo@linaro.org> wrote:
> >
> > Qualcomm SoCs based on the RPM architecture have a MSM Power Manager (MPM)
> > in always-on domain. In addition to managing resources during sleep, the
> > hardware also has an interrupt controller that monitors the interrupts
> > when the system is asleep, wakes up the APSS when one of these interrupts
> > occur and replays it to GIC after it becomes operational.
> >
> > It adds an irqchip driver for this interrupt controller, and here are
> > some notes about it.
> >
> > - For given SoC, a fixed number of MPM pins are supported, e.g. 96 pins
> > on QCM2290. Each of these MPM pins can be either a MPM_GIC pin or
> > a MPM_GPIO pin. The mapping between MPM_GIC pin and GIC interrupt
> > is defined by SoC, as well as the mapping between MPM_GPIO pin and
> > GPIO number. The former mapping can be found as the SoC data in this
> > MPM driver, while the latter can be found as the msm_gpio_wakeirq_map[]
> > in TLMM driver.
> >
> > - Two irq domains are created for a single irq_chip to handle MPM_GIC
> > and MPM_GPIO pins respectively, i.e. MPM_GIC domain and MPM_GPIO domain.
> > The former is a child domain of GIC irq domain, while the latter is
> > a parent domain of TLMM/GPIO irq domain.
> >
> > - All the register settings are done by APSS on the an internal memory
> > region called vMPM, and RPM will flush them into hardware after it
> > receives a mailbox/IPC notification from APSS.
> >
> > - When SoC gets awake from sleep mode, the driver will receive an
> > interrupt from RPM, so that it can replay interrupt for particular
> > polarity.
> >
> > Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
> > ---
> > drivers/irqchip/Kconfig | 8 +
> > drivers/irqchip/Makefile | 1 +
> > drivers/irqchip/qcom-mpm.c | 487 +++++++++++++++++++++++++++++++++++++
> > 3 files changed, 496 insertions(+)
> > create mode 100644 drivers/irqchip/qcom-mpm.c
> >
> > diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
> > index 7038957f4a77..e126b19190ef 100644
> > --- a/drivers/irqchip/Kconfig
> > +++ b/drivers/irqchip/Kconfig
> > @@ -430,6 +430,14 @@ config QCOM_PDC
> > Power Domain Controller driver to manage and configure wakeup
> > IRQs for Qualcomm Technologies Inc (QTI) mobile chips.
> >
> > +config QCOM_MPM
> > + bool "QCOM MPM"
>
> Can't be built as a module?

The driver is implemented as a builtin_platform_driver().

>
> > + depends on ARCH_QCOM
> > + select IRQ_DOMAIN_HIERARCHY
> > + help
> > + MSM Power Manager driver to manage and configure wakeup
> > + IRQs for Qualcomm Technologies Inc (QTI) mobile chips.
> > +
> > config CSKY_MPINTC
> > bool
> > depends on CSKY
> > diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
> > index c1f611cbfbf8..0e2e10467e28 100644
> > --- a/drivers/irqchip/Makefile
> > +++ b/drivers/irqchip/Makefile
> > @@ -94,6 +94,7 @@ obj-$(CONFIG_MESON_IRQ_GPIO) += irq-meson-gpio.o
> > obj-$(CONFIG_GOLDFISH_PIC) += irq-goldfish-pic.o
> > obj-$(CONFIG_NDS32) += irq-ativic32.o
> > obj-$(CONFIG_QCOM_PDC) += qcom-pdc.o
> > +obj-$(CONFIG_QCOM_MPM) += qcom-mpm.o
> > obj-$(CONFIG_CSKY_MPINTC) += irq-csky-mpintc.o
> > obj-$(CONFIG_CSKY_APB_INTC) += irq-csky-apb-intc.o
> > obj-$(CONFIG_RISCV_INTC) += irq-riscv-intc.o
> > diff --git a/drivers/irqchip/qcom-mpm.c b/drivers/irqchip/qcom-mpm.c
> > new file mode 100644
> > index 000000000000..1880c734155f
> > --- /dev/null
> > +++ b/drivers/irqchip/qcom-mpm.c
> > @@ -0,0 +1,487 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright (c) 2021, Linaro Limited
> > + * Copyright (c) 2010-2020, The Linux Foundation. All rights reserved.
> > + */
> > +
> > +#include <linux/delay.h>
> > +#include <linux/err.h>
> > +#include <linux/init.h>
> > +#include <linux/io.h>
> > +#include <linux/irqchip.h>
> > +#include <linux/irqchip/arm-gic-v3.h>
> > +#include <linux/irqdomain.h>
> > +#include <linux/mailbox_client.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/slab.h>
> > +#include <linux/spinlock.h>
> > +
> > +/*
> > + * vMPM register layout:
> > + *
> > + * 31 0
> > + * +--------------------------------+
> > + * | TIMER0 | 0x00
> > + * +--------------------------------+
> > + * | TIMER1 | 0x04
> > + * +--------------------------------+
> > + * | ENABLE0 | 0x08
> > + * +--------------------------------+
> > + * | ... | ...
> > + * +--------------------------------+
> > + * | ENABLEn |
> > + * +--------------------------------+
> > + * | FALLING_EDGE0 |
> > + * +--------------------------------+
> > + * | ... |
> > + * +--------------------------------+
> > + * | STATUSn |
> > + * +--------------------------------+
> > + *
> > + * n = DIV_ROUND_UP(pin_num, 32)
> > + *
> > + */
> > +#define MPM_REG_ENABLE 0
> > +#define MPM_REG_FALLING_EDGE 1
> > +#define MPM_REG_RISING_EDGE 2
> > +#define MPM_REG_POLARITY 3
> > +#define MPM_REG_STATUS 4
> > +
> > +#define MPM_NO_PARENT_IRQ ~0UL
> > +
> > +/* MPM pin and its GIC hwirq */
> > +struct mpm_pin {
> > + int pin;
> > + irq_hw_number_t hwirq;
> > +};
> > +
> > +struct mpm_data {
> > + unsigned int pin_num;
> > + const struct mpm_pin *gic_pins;
> > +};
> > +
> > +struct qcom_mpm_priv {
> > + void __iomem *base;
> > + spinlock_t lock;
> > + struct mbox_client mbox_client;
> > + struct mbox_chan *mbox_chan;
> > + const struct mpm_data *data;
> > + unsigned int reg_stride;
> > +
> > + /* MPM pin to Linux irq number */
> > + unsigned int *pin_to_irq;
> > +};
> > +
> > +static inline u32
> > +qcom_mpm_read(struct qcom_mpm_priv *priv, unsigned int reg, unsigned int index)
> > +{
> > + unsigned int offset = (reg * priv->reg_stride + index + 2) * 4;
> > +
> > + return readl(priv->base + offset);
> Why the non-relaxed accessors?

OK, will change to relaxed ones.

>
> > +}
> > +
> > +static inline void
> > +qcom_mpm_write(struct qcom_mpm_priv *priv, unsigned int reg,
> > + unsigned int index, u32 val)
> > +{
> > + unsigned int offset = (reg * priv->reg_stride + index + 2) * 4;
> > + u32 r_val;
> > +
> > + writel(val, priv->base + offset);
> > +
> > + do {
> > + r_val = readl(priv->base + offset);
> > + udelay(5);
> > + } while (r_val != val);
>
> What? Is this waiting for a bit to clear? Why isn't this one of the
> read*_poll_timeout*() function instead? Surely you can't wait forever
> here.

This is taken from downstream, and it seems to double check the written
value by reading it back. But to be honest, I'm not really this is
necessary. I will do some testing with the read-back check dropped.

>
> > +}
> > +
> > +static inline void qcom_mpm_enable_irq(struct irq_data *d, bool en)
> > +{
> > + struct qcom_mpm_priv *priv = d->domain->host_data;
>
> This really should be stored in d->chip_data.

OK.

>
> > + int pin = d->hwirq;
> > + unsigned int index = pin / 32;
> > + unsigned int shift = pin % 32;
> > + unsigned long flags;
> > + u32 val;
> > +
> > + priv->pin_to_irq[pin] = d->irq;
>
> This makes no sense. This is only reinventing the very notion of an
> irq domain, which is to lookup the Linux interrupt based on a context
> and a signal number.

The uniqueness of this driver is that it has two irq domains. This
little lookup table is created to avoid resolving mapping on each of
these domains, which is less efficient. But you think this is really
nonsense, I can change.

>
> > +
> > + spin_lock_irqsave(&priv->lock, flags);
>
> This must be a raw spinlock.

OK.

>
> > +
> > + val = qcom_mpm_read(priv, MPM_REG_ENABLE, index);
> > + if (en)
> > + val |= 1 << shift;
> > + else
> > + val &= ~(1 << shift);
>
> Use BIT(shift).

OK.

>
> > + qcom_mpm_write(priv, MPM_REG_ENABLE, index, val);
> > +
> > + spin_unlock_irqrestore(&priv->lock, flags);
> > +}
> > +
> > +static void qcom_mpm_mask(struct irq_data *d)
> > +{
> > + qcom_mpm_enable_irq(d, false);
> > +
> > + if (d->parent_data)
> > + irq_chip_mask_parent(d);
> > +}
> > +
> > +static void qcom_mpm_unmask(struct irq_data *d)
> > +{
> > + qcom_mpm_enable_irq(d, true);
> > +
> > + if (d->parent_data)
> > + irq_chip_unmask_parent(d);
> > +}
> > +
> > +static inline void
> > +mpm_set_type(struct qcom_mpm_priv *priv, bool set, unsigned int reg,
> > + unsigned int index, unsigned int shift)
> > +{
> > + u32 val;
> > +
> > + val = qcom_mpm_read(priv, reg, index);
> > + if (set)
> > + val |= 1 << shift;
> > + else
> > + val &= ~(1 << shift);
> > + qcom_mpm_write(priv, reg, index, val);
> > +}
> > +
> > +static int qcom_mpm_set_type(struct irq_data *d, unsigned int type)
> > +{
> > + struct qcom_mpm_priv *priv = d->domain->host_data;
> > + int pin = d->hwirq;
> > + unsigned int index = pin / 32;
> > + unsigned int shift = pin % 32;
> > + unsigned long flags;
> > +
> > + spin_lock_irqsave(&priv->lock, flags);
> > +
> > + mpm_set_type(priv, (type & IRQ_TYPE_EDGE_RISING) ? 1 : 0,
>
> You have a bool type as the second parameter. Why the convoluted ?:
> operator?

Will change to !!(type & IRQ_TYPE_EDGE_RISING).

>
> > + MPM_REG_RISING_EDGE, index, shift);
> > + mpm_set_type(priv, (type & IRQ_TYPE_EDGE_FALLING) ? 1 : 0,
> > + MPM_REG_FALLING_EDGE, index, shift);
> > + mpm_set_type(priv, (type & IRQ_TYPE_LEVEL_HIGH) ? 1 : 0,
> > + MPM_REG_POLARITY, index, shift);
>
> Why does this mean for an edge interrupt?

Edge polarity is configured above on MPM_REG_RISING_EDGE and
MPM_REG_FALLING_EDGE. So I guess MPM_REG_POLARITY doesn't have an
impact on edge interrupt. I do not have any document or information
other than downstream code to be sure though.

>
> > +
> > + spin_unlock_irqrestore(&priv->lock, flags);
> > +
> > + if (!d->parent_data)
> > + return 0;
> > +
> > + if (type & IRQ_TYPE_EDGE_BOTH)
> > + type = IRQ_TYPE_EDGE_RISING;
> > +
> > + if (type & IRQ_TYPE_LEVEL_MASK)
> > + type = IRQ_TYPE_LEVEL_HIGH;
> > +
> > + return irq_chip_set_type_parent(d, type);
> > +}
> > +
> > +static struct irq_chip qcom_mpm_chip = {
> > + .name = "mpm",
> > + .irq_eoi = irq_chip_eoi_parent,
> > + .irq_mask = qcom_mpm_mask,
> > + .irq_disable = qcom_mpm_mask,
>
> No. If disable is really mask, then you only need mask.

OK.

>
> > + .irq_unmask = qcom_mpm_unmask,
> > + .irq_retrigger = irq_chip_retrigger_hierarchy,
> > + .irq_set_type = qcom_mpm_set_type,
> > + .flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE,
> > + .irq_set_affinity = irq_chip_set_affinity_parent,
>
> nit: please align the members vertically.

Sure.

>
> > +};
> > +
> > +static irq_hw_number_t get_parent_hwirq(struct qcom_mpm_priv *priv, int pin)
> > +{
> > + const struct mpm_pin *gic_pins = priv->data->gic_pins;
> > + int i;
> > +
> > + for (i = 0; gic_pins[i].pin >= 0; i++) {
> > + int p = gic_pins[i].pin;
> > +
> > + if (p < 0)
> > + break;
> > +
> > + if (p == pin)
> > + return gic_pins[i].hwirq;
> > + }
> > +
> > + return MPM_NO_PARENT_IRQ;
> > +}
> > +
> > +static int
> > +qcom_mpm_translate(struct irq_domain *domain, struct irq_fwspec *fwspec,
> > + unsigned long *hwirq, unsigned int *type)
> > +{
> > + if (is_of_node(fwspec->fwnode)) {
> > + if (fwspec->param_count != 2)
> > + return -EINVAL;
> > +
> > + *hwirq = fwspec->param[0];
> > + *type = fwspec->param[1] & IRQ_TYPE_SENSE_MASK;
> > + return 0;
> > + }
> > +
> > + return -EINVAL;
> > +}
>
> This is a copy of irq_domain_translate_twocell().

OK.

>
> > +
> > +static int qcom_mpm_gic_alloc(struct irq_domain *domain, unsigned int virq,
> > + unsigned int nr_irqs, void *data)
> > +{
> > + struct qcom_mpm_priv *priv = domain->host_data;
> > + struct irq_fwspec *fwspec = data;
> > + struct irq_fwspec parent_fwspec;
> > + irq_hw_number_t parent_hwirq;
> > + irq_hw_number_t hwirq;
> > + unsigned int type;
> > + int ret;
> > +
> > + ret = qcom_mpm_translate(domain, fwspec, &hwirq, &type);
> > + if (ret)
> > + return ret;
> > +
> > + ret = irq_domain_set_hwirq_and_chip(domain, virq, hwirq,
> > + &qcom_mpm_chip, NULL);
> > + if (ret)
> > + return ret;
> > +
> > + parent_hwirq = get_parent_hwirq(priv, hwirq);
> > + if (parent_hwirq == MPM_NO_PARENT_IRQ)
> > + return irq_domain_disconnect_hierarchy(domain->parent, virq);
> > +
> > + if (type & IRQ_TYPE_EDGE_BOTH)
> > + type = IRQ_TYPE_EDGE_RISING;
> > +
> > + if (type & IRQ_TYPE_LEVEL_MASK)
> > + type = IRQ_TYPE_LEVEL_HIGH;
> > +
> > + parent_fwspec.fwnode = domain->parent->fwnode;
> > + parent_fwspec.param_count = 3;
> > + parent_fwspec.param[0] = 0;
> > + parent_fwspec.param[1] = parent_hwirq;
> > + parent_fwspec.param[2] = type;
> > +
> > + return irq_domain_alloc_irqs_parent(domain, virq, nr_irqs,
> > + &parent_fwspec);
> > +}
> > +
> > +static const struct irq_domain_ops qcom_mpm_gic_ops = {
> > + .alloc = qcom_mpm_gic_alloc,
> > + .free = irq_domain_free_irqs_common,
> > + .translate = qcom_mpm_translate,
>
> Same nit as above.
>
> > +};
> > +
> > +static int qcom_mpm_gpio_alloc(struct irq_domain *domain, unsigned int virq,
> > + unsigned int nr_irqs, void *data)
> > +{
> > + struct irq_fwspec *fwspec = data;
> > + unsigned int type = IRQ_TYPE_NONE;
> > + irq_hw_number_t hwirq;
> > + int ret;
> > +
> > + ret = qcom_mpm_translate(domain, fwspec, &hwirq, &type);
> > + if (ret)
> > + return ret;
> > +
> > + return irq_domain_set_hwirq_and_chip(domain, virq, hwirq,
> > + &qcom_mpm_chip, NULL);
> > +}
> > +
> > +static int qcom_mpm_gpio_domain_select(struct irq_domain *domain,
> > + struct irq_fwspec *fwspec,
> > + enum irq_domain_bus_token bus_token)
> > +{
> > + return bus_token == DOMAIN_BUS_WAKEUP;
> > +}
> > +
> > +static const struct irq_domain_ops qcom_mpm_gpio_ops = {
> > + .select = qcom_mpm_gpio_domain_select,
> > + .alloc = qcom_mpm_gpio_alloc,
> > + .free = irq_domain_free_irqs_common,
> > + .translate = qcom_mpm_translate,
> > +};
> > +
> > +/* Triggered by RPM when system resumes from deep sleep */
> > +static irqreturn_t qcom_mpm_handler(int irq, void *dev_id)
> > +{
> > + struct qcom_mpm_priv *priv = dev_id;
> > + unsigned long enable, pending;
> > + int i, j;
> > +
> > + for (i = 0; i < priv->reg_stride; i++) {
> > + enable = qcom_mpm_read(priv, MPM_REG_ENABLE, i);
> > + pending = qcom_mpm_read(priv, MPM_REG_STATUS, i);
> > + pending &= enable;
> > +
> > + for_each_set_bit(j, &pending, 32) {
> > + unsigned int pin = 32 * i + j;
> > + int irq = priv->pin_to_irq[pin];
> > + struct irq_desc *desc = irq ? irq_to_desc(irq) : NULL;
>
> How can this be 0 if you have masked out the disabled interrupts?

OK.

>
> > +
> > + if (desc && !irqd_is_level_type(&desc->irq_data))
> > + irq_set_irqchip_state(irq,
> > + IRQCHIP_STATE_PENDING, true);
> > +
> > + }
> > + }
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int qcom_mpm_probe(struct platform_device *pdev)
> > +{
> > + struct irq_domain *parent_domain, *mpm_gic_domain, *mpm_gpio_domain;
> > + struct device *dev = &pdev->dev;
> > + struct device_node *np = dev->of_node;
> > + struct device_node *parent = of_irq_find_parent(np);
> > + struct qcom_mpm_priv *priv;
> > + unsigned int pin_num;
> > + int irq;
> > + int ret;
> > +
> > + /* See comments in platform_irqchip_probe() */
> > + if (parent && !irq_find_matching_host(parent, DOMAIN_BUS_ANY))
> > + return -EPROBE_DEFER;
>
> So why aren't you using that infrastructure?

Because I need to populate .pm of platform_driver and use match data to
pass mpm_data.

>
> > +
> > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> > + if (!priv)
> > + return -ENOMEM;
> > +
> > + priv->data = of_device_get_match_data(dev);
> > + if (!priv->data)
> > + return -ENODEV;
> > +
> > + pin_num = priv->data->pin_num;
> > + priv->pin_to_irq = devm_kcalloc(dev, pin_num, sizeof(*priv->pin_to_irq),
> > + GFP_KERNEL);
> > + if (!priv)
> > + return -ENOMEM;
> > +
> > + priv->reg_stride = DIV_ROUND_UP(pin_num, 32);
> > + spin_lock_init(&priv->lock);
> > +
> > + priv->base = devm_platform_ioremap_resource(pdev, 0);
> > + if (!priv->base)
> > + return PTR_ERR(priv->base);
> > +
> > + irq = platform_get_irq(pdev, 0);
> > + if (irq < 0)
> > + return irq;
> > +
> > + parent_domain = irq_find_host(parent);
> > + if (!parent_domain) {
> > + dev_err(dev, "failed to find MPM parent domain\n");
> > + return -ENXIO;
> > + }
> > +
> > + mpm_gic_domain = irq_domain_create_hierarchy(parent_domain, 0, pin_num,
> > + of_node_to_fwnode(np), &qcom_mpm_gic_ops, priv);
> > + if (!mpm_gic_domain) {
> > + dev_err(dev, "failed to create GIC domain\n");
>
> The message is pretty misleading.

OK, will add MPM_ prefix.

>
> > + return -ENOMEM;
> > + }
> > +
> > + mpm_gpio_domain = irq_domain_create_linear(of_node_to_fwnode(np),
> > + pin_num, &qcom_mpm_gpio_ops, priv);
> > + if (!mpm_gpio_domain) {
> > + dev_err(dev, "failed to create GPIO domain\n");
> > + goto remove_gic_domain;
> > + }
> > +
> > + irq_domain_update_bus_token(mpm_gpio_domain, DOMAIN_BUS_WAKEUP);
> > +
> > + priv->mbox_client.dev = dev;
> > + priv->mbox_chan = mbox_request_channel(&priv->mbox_client, 0);
> > + if (IS_ERR(priv->mbox_chan)) {
> > + ret = PTR_ERR(priv->mbox_chan);
> > + dev_err(dev, "failed to acquire IPC channel: %d\n", ret);
> > + goto remove_gpio_domain;
>
> Why don't you request this first, before all the allocations?

Then I will need to call mbox_free_channel() for any allocation failures
afterward.

>
> > + }
> > +
> > + ret = devm_request_irq(dev, irq, qcom_mpm_handler,
> > + IRQF_TRIGGER_RISING | IRQF_NO_SUSPEND,
> > + "qcom_mpm", priv);
> > + if (ret) {
> > + dev_err(dev, "failed to request irq: %d\n", ret);
> > + goto free_mbox;
> > + }
> > +
> > + dev_set_drvdata(dev, priv);
> > +
> > + return 0;
> > +
> > +free_mbox:
> > + mbox_free_channel(priv->mbox_chan);
> > +remove_gpio_domain:
> > + irq_domain_remove(mpm_gpio_domain);
> > +remove_gic_domain:
> > + irq_domain_remove(mpm_gic_domain);
> > + return ret;
> > +}
> > +
> > +static int __maybe_unused qcom_mpm_suspend_late(struct device *dev)
> > +{
> > + struct qcom_mpm_priv *priv = dev_get_drvdata(dev);
> > + int i, ret;
> > +
> > + for (i = 0; i < priv->reg_stride; i++)
> > + qcom_mpm_write(priv, MPM_REG_STATUS, i, 0);
> > +
> > + /* Notify RPM to write vMPM into HW */
> > + ret = mbox_send_message(priv->mbox_chan, NULL);
> > + if (ret < 0)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +
> > +static int __maybe_unused qcom_mpm_resume_early(struct device *dev)
> > +{
> > + /* Nothing to do for now */
> > + return 0;
> > +}
> > +
> > +static const struct dev_pm_ops qcom_mpm_pm_ops = {
> > + SET_LATE_SYSTEM_SLEEP_PM_OPS(qcom_mpm_suspend_late,
> > + qcom_mpm_resume_early)
> > +};
> > +
> > +/* Taken from downstream qcom-mpm-scuba.c with hwirq number minus 32 */
>
> So is that a full description? Or are we only hoping that this is good
> enough?

I will improve this documentation.

Thanks for your time, Marc!

Shawn

>
> > +const struct mpm_pin qcm2290_gic_pins[] = {
> > + { 2, 275 }, /* tsens0_tsens_upper_lower_int */
> > + { 5, 296 }, /* lpass_irq_out_sdc */
> > + { 12, 422 }, /* b3_lfps_rxterm_irq */
> > + { 24, 79 }, /* bi_px_lpi_1_aoss_mx */
> > + { 86, 183 }, /* mpm_wake,spmi_m */
> > + { 90, 260 }, /* eud_p0_dpse_int_mx */
> > + { 91, 260 }, /* eud_p0_dmse_int_mx */
> > + { -1 },
> > +};
> > +
> > +const struct mpm_data qcm2290_data = {
> > + .pin_num = 96,
> > + .gic_pins = qcm2290_gic_pins,
> > +};
> > +
> > +static const struct of_device_id qcom_mpm_match_table[] = {
> > + { .compatible = "qcom,qcm2290-mpm", &qcm2290_data, },
> > + { },
> > +};
> > +
> > +static struct platform_driver qcom_mpm_driver = {
> > + .driver = {
> > + .name = "qcom_mpm",
> > + .owner = THIS_MODULE,
> > + .of_match_table = qcom_mpm_match_table,
> > + .pm = &qcom_mpm_pm_ops,
> > + .suppress_bind_attrs = true,
> > + },
> > + .probe = qcom_mpm_probe,
> > +};
> > +builtin_platform_driver(qcom_mpm_driver)
> > +
> > +MODULE_DESCRIPTION("Qualcomm Technologies, Inc. MSM Power Manager");
> > +MODULE_LICENSE("GPL v2");

\
 
 \ /
  Last update: 2021-11-29 16:12    [W:0.114 / U:0.848 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site