lkml.org 
[lkml]   [2021]   [Nov]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] Bluetooth: virtio_bt: fix device removal
On Thu, Nov 25, 2021 at 10:58:56PM +0100, Marcel Holtmann wrote:
> Hi Michael,
>
> >>>>> Device removal is clearly out of virtio spec: it attempts to remove
> >>>>> unused buffers from a VQ before invoking device reset. To fix, make
> >>>>> open/close NOPs and do all cleanup/setup in probe/remove.
> >>>>
> >>>> so the virtbt_{open,close} as NOP is not really what a driver is suppose
> >>>> to be doing. These are transport enable/disable callbacks from the BT
> >>>> Core towards the driver. It maps to a device being enabled/disabled by
> >>>> something like bluetoothd for example. So if disabled, I expect that no
> >>>> resources/queues are in use.
> >>>>
> >>>> Maybe I misunderstand the virtio spec in that regard, but I would like
> >>>> to keep this fundamental concept of a Bluetooth driver. It does work
> >>>> with all other transports like USB, SDIO, UART etc.
> >>>>
> >>>>> The cost here is a single skb wasted on an unused bt device - which
> >>>>> seems modest.
> >>>>
> >>>> There should be no buffer used if the device is powered off. We also don’t
> >>>> have any USB URBs in-flight if the transport is not active.
> >>>>
> >>>>> NB: with this fix in place driver still suffers from a race condition if
> >>>>> an interrupt triggers while device is being reset. Work on a fix for
> >>>>> that issue is in progress.
> >>>>
> >>>> In the virtbt_close() callback we should deactivate all interrupts.
> >>>>
> >>>
> >>> If you want to do that then device has to be reset on close,
> >>> and fully reinitialized on open.
> >>> Can you work on a patch like that?
> >>> Given I don't have the device such a rework is probably more
> >>> than I can undertake.
> >>
> >> so you mean move virtio_find_vqs() into virtbt_open() and del_vqs() into
> >> virtbt_close()?
> >
> > And reset before del_vqs.
> >
> >> Or is there are way to set up the queues without starting them?
> >>
> >> However I am failing to understand your initial concern, we do reset()
> >> before del_vqs() in virtbt_remove(). Should we be doing something different
> >> in virtbt_close() other than virtqueue_detach_unused_buf(). Why would I
> >> keep buffers attached if they are not used.
> >>
> >
> > They are not used at that point but until device is reset can use them.
> > Also, if you then proceed to open without a reset, and kick,
> > device will start by processing the original buffers, crashing
> > or corrupting memory.
>
> so the only valid usage is like this:
>
> vdev->config->reset(vdev);
>
> while ((.. = virtqueue_detach_unused_buf(vq))) {
> }
>
> vdev->config->del_vqs(vdev);
>
> If I make virtbt_{open,close} a NOP, then I keep adding an extra SKB to inbuf on
> every power cycle (ifup/ifdown).

So make sure you don't :)

> How does netdev handle this?
>
> Regards
>
> Marcel

For net, open adds buffers to vq. close does not free them up -
they stay in the vq until device is removed.

--
MST

\
 
 \ /
  Last update: 2021-11-26 02:05    [W:0.277 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site