lkml.org 
[lkml]   [2021]   [Nov]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v2 1/2] watchdog: Add watchdog driver for Sunplus SP7021
Date
Hi
Thanks for your review. I explain this in detail below the comment.

Best Regards,
Xiantao
> -----Original Message-----
> From: Guenter Roeck [mailto:groeck7@gmail.com] On Behalf Of Guenter Roeck
> Sent: Wednesday, November 24, 2021 10:25 PM
> To: xt.hu[胡先韬] <xt.hu@cqplus1.com>
> Cc: wim@linux-watchdog.org; p.zabel@pengutronix.de; linux-kernel@vger.kernel.org;
> linux-watchdog@vger.kernel.org; robh+dt@kernel.org; devicetree@vger.kernel.org; Wells Lu 呂芳騰
> <wells.lu@sunplus.com>; qinjian[覃健] <qinjian@cqplus1.com>
> Subject: Re: [PATCH v2 1/2] watchdog: Add watchdog driver for Sunplus SP7021
>
> On Wed, Nov 24, 2021 at 06:41:48PM +0800, Xiantao Hu wrote:
> > Sunplus SP7021 requires watchdog timer support.
> > Add watchdog driver to enable this.
> >
> > Signed-off-by: Xiantao Hu <xt.hu@cqplus1.com>
> > ---
> > +
> > + priv->base = devm_platform_ioremap_resource(pdev, 0);
> > + if (IS_ERR(priv->base))
> > + return PTR_ERR(priv->base);
> > +
> > + /* The registers accessed here shared by multiple drivers. */
> > + wdt_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>
> This is unusual. Why would other drivers access WDT_CTRL and WDT_CNT registers, and how is it
> ensured that the other drivers do not interfer with the accesses by this driver ?
>
> Normally such a resource would be shared through a parent driver with appropriate access functions to
> ensure that accesses are synchronized.
>

The register used by this driver consists of two parts. The first part which contains WDT_CTRL and WDT_CNT
registers is exclusive by watchdog.
In specially, the second part is belong to a multifunctional register group which control IP and bus. Refer to
register manual below:
-------------------------------------------------------------------------------------------------------------------------------------------------
MO1_STC_WDG_RST_EN 4 RW STC Watchdog Timeout Trigger System Reset Enable
0: STC watchdog 2 timeout will not trigger system reset(default)
1: STC watchdog 2 timeout will trigger system reset
MO1_RI_WDG_RST_EN 1 RW RBUS Watchdog Timeout Trigger System Reset Enable
0: RBUS watchdog timeout will not trigger system reset(default)
1: RBUS watchdog timeout will trigger system reset
MO1_TIMER_STAND_BY_EN 0 RW Timer Standby Mode Enable
0: Disable (default)
1: Enable Active high to enter timer standby mode,
default not in standby mode
-------------------------------------------------------------------------------------------------------------------------------------------------
You can see that in addition to the bits for watchdog there are bit fields for other modules.
I use this register bit4 and bit1. Default value is 0 that watchdog internal interrupt signal can't trigger system
and RBUS reset. I need set 1 when watchdog probe. Early I implement the operation in
arch/arm/mach-sunplus/sp7021.c and configure by macro. But in arch/arm64, directory mach-XXX is removed.
So I solve in this way. Any better way?

> Thanks,
> Guenter
\
 
 \ /
  Last update: 2021-11-25 03:46    [W:0.062 / U:5.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site