lkml.org 
[lkml]   [2021]   [Nov]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/4] arm64: dts: qcom: sc7280-crd: Add Touchscreen and touchpad support
On Tue, Nov 23, 2021 at 12:30:13PM +0530, Rajendra Nayak wrote:
> From: Kshitiz Godara <kgodara@codeaurora.org>
>
> Add Touchscreen and touchpad hid-over-i2c node

to which board(s)?

> Signed-off-by: Kshitiz Godara <kgodara@codeaurora.org>
> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
> ---
> arch/arm64/boot/dts/qcom/sc7280-crd.dts | 63 +++++++++++++++++++++++++++++++++
> 1 file changed, 63 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> index 8c2aee6..bef3037 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
> @@ -23,6 +23,47 @@
> };
> };
>
> +ap_tp_i2c: &i2c0 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + trackpad: trackpad@15 {
> + compatible = "hid-over-i2c";
> + reg = <0x15>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&tp_int_odl>;
> +
> + interrupt-parent = <&tlmm>;
> + interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
> +
> + post-power-on-delay-ms = <20>;
> + hid-descr-addr = <0x0001>;
> + vdd-supply = <&vreg_l18b_1p8>;
> +
> + wakeup-source;
> + };
> +};
> +
> +ap_ts_pen_1v8: &i2c13 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + ap_ts: touchscreen@5c {
> + compatible = "hid-over-i2c";
> + reg = <0x5C>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
> +
> + interrupt-parent = <&tlmm>;
> + interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
> +
> + post-power-on-delay-ms = <500>;
> + hid-descr-addr = <0x0000>;
> +
> + vdd-supply = <&vreg_l19b_1p8>;
> + };
> +};
> +
> &nvme_pwren {
> pins = "gpio51";
> };
> @@ -30,3 +71,25 @@
> &nvme_3v3_regulator {
> gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
> };
> +
> +&tlmm {
> + tp_int_odl: tp-int-odl {
> + pins = "gpio7";
> + function = "gpio";
> + input-enable;

Not sure about this one, is the explicit 'input-enable' actually needed here?

> + bias-disable;
> + };
> +
> + ts_int_l: ts-int-l {
> + pins = "gpio55";
> + function = "gpio";
> + bias-pull-up;
> + };
> +
> + ts_reset_l: ts-reset-l {
> + pins = "gpio54";
> + function = "gpio";
> + bias-disable;
> + drive-strength = <2>;

As per my comment on "[3/4] arm64: dts: qcom: sc7280: Define EC and H1 nodes" it
seems setting the drive strength to 2 isn't necessary, since that's the default.

\
 
 \ /
  Last update: 2021-11-23 18:59    [W:0.154 / U:1.388 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site