lkml.org 
[lkml]   [2021]   [Nov]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v2] PCI: apple: Follow the PCIe specifications when resetting the port
On Mon, 22 Nov 2021 21:50:48 +0000,
Mark Kettenis <mark.kettenis@xs4all.nl> wrote:
>
> > Date: Mon, 22 Nov 2021 14:43:37 +0000
> > From: Marc Zyngier <maz@kernel.org>
> >
> > On Mon, 22 Nov 2021 12:03:47 +0000,
> > Pali Rohár <pali@kernel.org> wrote:
> > >
> > > On Monday 22 November 2021 10:41:56 Marc Zyngier wrote:
> > > > While the Apple PCIe driver works correctly when directly booted
> > > > from the firmware, it fails to initialise when the kernel is booted
> > > > from a bootloader using PCIe such as u-boot.
> > > >
> > > > That's beacuse we're missing a proper reset of the port (we only
> > > > clear the reset, but never assert it).
> > > >
> > > > The PCIe spec requirements are two-fold:
> > > >
> > > > - #PERST must be asserted before setting up the clocks, and
> > > > stay asserted for at least 100us (Tperst-clk).
> > > >
> > > > - Once #PERST is deasserted, the OS must wait for at least 100ms
> > > > "from the end of a Conventional Reset" before we can start talking
> > > > to the devices
> > > >
> > > > Implementing this results in a booting system.
> > > >
> > > > Fixes: 1e33888fbe44 ("PCI: apple: Add initial hardware bring-up")
> > > > Signed-off-by: Marc Zyngier <maz@kernel.org>
> > > > Cc: Alyssa Rosenzweig <alyssa@rosenzweig.io>
> > > > Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
> > > > Cc: Bjorn Helgaas <bhelgaas@google.com>
> > > > Cc: Pali Rohár <pali@kernel.org>
> > >
> > > Looks good, but see comment below.
> > >
> > > Acked-by: Pali Rohár <pali@kernel.org>
> >
> > Thanks for that.
> >
> > >
> > > > ---
> > > > drivers/pci/controller/pcie-apple.c | 10 ++++++++++
> > > > 1 file changed, 10 insertions(+)
> > > >
> > > > diff --git a/drivers/pci/controller/pcie-apple.c b/drivers/pci/controller/pcie-apple.c
> > > > index 1bf4d75b61be..957960a733c4 100644
> > > > --- a/drivers/pci/controller/pcie-apple.c
> > > > +++ b/drivers/pci/controller/pcie-apple.c
> > > > @@ -539,13 +539,23 @@ static int apple_pcie_setup_port(struct apple_pcie *pcie,
> > > >
> > > > rmw_set(PORT_APPCLK_EN, port->base + PORT_APPCLK);
> > > >
> > > > + /* Engage #PERST before setting up the clock */
> > > > + gpiod_set_value(reset, 0);
> > > > +
> > > > ret = apple_pcie_setup_refclk(pcie, port);
> > > > if (ret < 0)
> > > > return ret;
> > > >
> > > > + /* The minimal Tperst-clk value is 100us (PCIe CMS r2.0, 2.6.2) */
> > > > + usleep_range(100, 200);
> > > > +
> > > > + /* Deassert #PERST */
> > > > rmw_set(PORT_PERST_OFF, port->base + PORT_PERST);
> > > > gpiod_set_value(reset, 1);
> > >
> > > + Luca
> > >
> > > Just one comment. PERST# (PCIe Reset) is active-low signal. De-asserting
> > > means to really set value to 1.
> > >
> > > But there was a discussion that de-asserting should be done by call:
> > > gpiod_set_value(reset, 0);
> > >
> > > https://lore.kernel.org/linux-pci/51be082a-ff10-8a19-5648-f279aabcac51@lucaceresoli.net/
> > >
> > > Could we make this new pcie-apple.c driver to use gpiod_set_value(reset, 0)
> > > for de-asserting, like in other drivers?
> >
> > I guess it depends whether you care about the assertion or the signal
> > itself. I think we may have a bug in the way the GPIOs are handled at
> > the moment, as it makes no difference whether I register the GPIO are
> > active high or active low...
>
> That's unfortunate. But maybe that's an opportunity to fix the
> devicetree to use GPIO_ACTIVE_LOW for these GPIOs?

Indeed. The following hack does the right thing, and I can then
reverse the polarity of the reset in the Linux driver. Of course, it
breaks u-boot at the same time (and I suspect OpenBSD would be equally
affected).

So if we are going down that road, we may need a flag day where all
the moving parts change. I don't really mind not being able to boot
older kernels, but this goes beyond Linux at this point.

Thanks,

M.

diff --git a/arch/arm64/boot/dts/apple/t8103.dtsi b/arch/arm64/boot/dts/apple/t8103.dtsi
index d2e9afde3729..cad1ab920304 100644
--- a/arch/arm64/boot/dts/apple/t8103.dtsi
+++ b/arch/arm64/boot/dts/apple/t8103.dtsi
@@ -10,6 +10,7 @@
#include <dt-bindings/interrupt-controller/apple-aic.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/apple.h>
+#include <dt-bindings/gpio/gpio.h>

/ {
compatible = "apple,t8103", "apple,arm-platform";
@@ -293,7 +294,7 @@ pcie0: pcie@690000000 {
port00: pci@0,0 {
device_type = "pci";
reg = <0x0 0x0 0x0 0x0 0x0>;
- reset-gpios = <&pinctrl_ap 152 0>;
+ reset-gpios = <&pinctrl_ap 152 GPIO_ACTIVE_LOW>;
max-link-speed = <2>;

#address-cells = <3>;
@@ -313,7 +314,7 @@ port00: pci@0,0 {
port01: pci@1,0 {
device_type = "pci";
reg = <0x800 0x0 0x0 0x0 0x0>;
- reset-gpios = <&pinctrl_ap 153 0>;
+ reset-gpios = <&pinctrl_ap 153 GPIO_ACTIVE_LOW>;
max-link-speed = <2>;

#address-cells = <3>;
@@ -333,7 +334,7 @@ port01: pci@1,0 {
port02: pci@2,0 {
device_type = "pci";
reg = <0x1000 0x0 0x0 0x0 0x0>;
- reset-gpios = <&pinctrl_ap 33 0>;
+ reset-gpios = <&pinctrl_ap 33 GPIO_ACTIVE_LOW>;
max-link-speed = <1>;

#address-cells = <3>;
--
Without deviation from the norm, progress is not possible.

\
 
 \ /
  Last update: 2021-11-23 13:25    [W:0.627 / U:0.536 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site