lkml.org 
[lkml]   [2021]   [Nov]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[net-next PATCH] net: dsa: qca8k: make sure PAD0 MAC06 exchange is disabled
Date
Some device set MAC06 exchange in the bootloader. This cause some
problem as we don't support this strange mode and we just set the port6
as the primary CPU port. With MAC06 exchange, PAD0 reg configure port6
instead of port0. Add an extra check and explicitly disable MAC06 exchange
to correctly configure the port PAD config.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
---
drivers/net/dsa/qca8k.c | 8 ++++++++
drivers/net/dsa/qca8k.h | 1 +
2 files changed, 9 insertions(+)

Some comments here:
Resetting the switch using the sw reg doesn't reset the port PAD
configuration. I was thinking if it would be better to clear all the
pad configuration but considering that the entire reg is set by phylink
mac config, I think it's not necessary as the PAD related to the port will
be reset anyway with the new values. Have a dirty configuration on PAD6
doesn't cause any problem as we have that port disabled and it would be
reset and configured anyway if defined.

diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
index ea7f12778922..a429c9750add 100644
--- a/drivers/net/dsa/qca8k.c
+++ b/drivers/net/dsa/qca8k.c
@@ -1109,6 +1109,14 @@ qca8k_setup(struct dsa_switch *ds)
if (ret)
return ret;

+ /* Make sure MAC06 is disabled */
+ ret = qca8k_reg_clear(priv, QCA8K_REG_PORT0_PAD_CTRL,
+ QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN);
+ if (ret) {
+ dev_err(priv->dev, "failed disabling MAC06 exchange");
+ return ret;
+ }
+
/* Enable CPU Port */
ret = qca8k_reg_set(priv, QCA8K_REG_GLOBAL_FW_CTRL0,
QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN);
diff --git a/drivers/net/dsa/qca8k.h b/drivers/net/dsa/qca8k.h
index e10571a398c9..128b8cf85e08 100644
--- a/drivers/net/dsa/qca8k.h
+++ b/drivers/net/dsa/qca8k.h
@@ -34,6 +34,7 @@
#define QCA8K_MASK_CTRL_DEVICE_ID_MASK GENMASK(15, 8)
#define QCA8K_MASK_CTRL_DEVICE_ID(x) ((x) >> 8)
#define QCA8K_REG_PORT0_PAD_CTRL 0x004
+#define QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN BIT(31)
#define QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE BIT(19)
#define QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE BIT(18)
#define QCA8K_REG_PORT5_PAD_CTRL 0x008
--
2.32.0
\
 
 \ /
  Last update: 2021-11-02 18:57    [W:0.053 / U:0.120 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site