lkml.org 
[lkml]   [2021]   [Nov]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v3 6/6] KVM: selftests: test KVM_GUESTDBG_BLOCKIRQ
Date
Sean Christopherson <seanjc@google.com> writes:

> On Tue, Nov 02, 2021, Vitaly Kuznetsov wrote:
>> Sean Christopherson <seanjc@google.com> writes:
>> > I haven't verified on hardware, but my guess is that this code in vmx_vcpu_run()
>> >
>> > /* When single-stepping over STI and MOV SS, we must clear the
>> > * corresponding interruptibility bits in the guest state. Otherwise
>> > * vmentry fails as it then expects bit 14 (BS) in pending debug
>> > * exceptions being set, but that's not correct for the guest debugging
>> > * case. */
>> > if (vcpu->guest_debug & KVM_GUESTDBG_SINGLESTEP)
>> > vmx_set_interrupt_shadow(vcpu, 0);
>> >
>> > interacts badly with APICv=1. It will kill the STI shadow and cause the IRQ in
>> > vmcs.GUEST_RVI to be recognized when it (micro-)architecturally should not. My
>> > head is going in circles trying to sort out what would actually happen. Maybe
>> > comment out that and/or disable APICv to see if either one makes the test pass?
>> >
>>
>> Interestingly,
>>
>> loading 'kvm-intel' with 'enable_apicv=0' makes the test pass, however,
>> commenting out "vmx_set_interrupt_shadow()" as suggested gives a
>> different result (with enable_apicv=1):
>>
>> # ./x86_64/debug_regs
>> ==== Test Assertion Failure ====
>> x86_64/debug_regs.c:179: run->exit_reason == KVM_EXIT_DEBUG && run->debug.arch.exception == DB_VECTOR && run->debug.arch.pc == target_rip && run->debug.arch.dr6 == target_dr6
>> pid=16352 tid=16352 errno=0 - Success
>> 1 0x0000000000402b33: main at debug_regs.c:179 (discriminator 10)
>> 2 0x00007f36401bd554: ?? ??:0
>> 3 0x00000000004023a9: _start at ??:?
>> SINGLE_STEP[1]: exit 9 exception -2147483615 rip 0x1 (should be 0x4024d9) dr6 0xffff4ff0 (should be 0xffff4ff0)
>
> Exit 9 is KVM_EXIT_FAIL_ENTRY, which in this case VM-Entry likely failed due to
> invalid guest state because there was STI blocking with single-step enabled but
> no pending BS #DB:
>
> Bit 14 (BS) must be 1 if the TF flag (bit 8) in the RFLAGS field is 1 and the
> BTF flag (bit 1) in the IA32_DEBUGCTL field is 0.
>
> Which is precisely what that hack-a-fix avoids. There isn't really a clean
> solution for legacy single-step, AFAIK the only way to avoid this would be to
> switch KVM_GUESTDBG_SINGLESTEP to use MTF.
>
> But that mess is a red herring, the test fails with the same signature with APICv=1
> if the STI is replaced by PUSHF+BTS+POPFD (to avoid the STI shadow). We all missed
> this key detail from Vitaly's report:
>
> SINGLE_STEP[1]: exit 8 exception 1 rip 0x402a25 (should be 0x402a27) dr6 0xffff4ff0 (should be 0xffff4ff0)
> ^^^^^^
>
> Exit '8' is KVM_EXIT_SHUTDOWN, i.e. the arrival of the IRQ hosed the guest because
> the test doesn't invoke vm_init_descriptor_tables() to install event handlers.
> The "exception 1" shows up because the run page isn't sanitized by the test, i.e.
> it's stale data that happens to match.
>
> So I would fully expect this test to fail with AVIC=1. The problem is that
> KVM_GUESTDBG_BLOCKIRQ does absolutely nothing to handle APICv interrupts. And
> even if KVM does something to fudge that behavior in the emulated local APIC, the
> test will then fail miserably virtual IPIs (currently AVIC only).

FWIW, the test doesn't seem to fail on my AMD EPYC system even with "avic=1" ...

>
> I stand by my original comment that "Deviating this far from architectural behavior
> will end in tears at some point." Rather than try to "fix" APICv, I vote to instead
> either reject KVM_GUESTDBG_BLOCKIRQ if APICv=1, or log a debug message saying that
> KVM_GUESTDBG_BLOCKIRQ is ineffective with APICv=1.
>

--
Vitaly

\
 
 \ /
  Last update: 2021-11-02 17:43    [W:0.109 / U:1.440 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site