lkml.org 
[lkml]   [2021]   [Nov]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [net-next PATCH 05/19] net: dsa: qca8k: move read switch id function in qca8k_setup
On Wed, Nov 17, 2021 at 10:04:37PM +0100, Ansuel Smith wrote:
> Move read_switch_id function in qca8k_setup in preparation for regmap
> conversion. Sw probe should NOT contain function that depends on reading
> from switch regs.

It shouldn't? Why? We have plenty of switch drivers that use regmap in
the probe function.

>
> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
> ---
> drivers/net/dsa/qca8k.c | 71 ++++++++++++++++++++---------------------
> 1 file changed, 35 insertions(+), 36 deletions(-)
>
> diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
> index 19331edf1fd4..be98d11b17ec 100644
> --- a/drivers/net/dsa/qca8k.c
> +++ b/drivers/net/dsa/qca8k.c
> @@ -1073,6 +1073,36 @@ qca8k_parse_port_config(struct qca8k_priv *priv)
> return 0;
> }
>
> +static int qca8k_read_switch_id(struct qca8k_priv *priv)
> +{
> + const struct qca8k_match_data *data;
> + u32 val;
> + u8 id;
> + int ret;
> +
> + /* get the switches ID from the compatible */
> + data = of_device_get_match_data(priv->dev);
> + if (!data)
> + return -ENODEV;
> +
> + ret = qca8k_read(priv, QCA8K_REG_MASK_CTRL, &val);
> + if (ret < 0)
> + return -ENODEV;
> +
> + id = QCA8K_MASK_CTRL_DEVICE_ID(val);
> + if (id != data->id) {
> + dev_err(priv->dev, "Switch id detected %x but expected %x", id, data->id);
> + return -ENODEV;
> + }
> +
> + priv->switch_id = id;
> +
> + /* Save revision to communicate to the internal PHY driver */
> + priv->switch_revision = QCA8K_MASK_CTRL_REV_ID(val);
> +
> + return 0;
> +}
> +
> static int
> qca8k_setup(struct dsa_switch *ds)
> {
> @@ -1080,6 +1110,11 @@ qca8k_setup(struct dsa_switch *ds)
> int cpu_port, ret, i;
> u32 mask;
>
> + /* Check the detected switch id */
> + ret = qca8k_read_switch_id(priv);
> + if (ret)
> + return ret;
> +
> cpu_port = qca8k_find_cpu_port(ds);
> if (cpu_port < 0) {
> dev_err(priv->dev, "No cpu port configured in both cpu port0 and port6");
> @@ -2023,41 +2058,10 @@ static const struct dsa_switch_ops qca8k_switch_ops = {
> .get_phy_flags = qca8k_get_phy_flags,
> };
>
> -static int qca8k_read_switch_id(struct qca8k_priv *priv)
> -{
> - const struct qca8k_match_data *data;
> - u32 val;
> - u8 id;
> - int ret;
> -
> - /* get the switches ID from the compatible */
> - data = of_device_get_match_data(priv->dev);
> - if (!data)
> - return -ENODEV;
> -
> - ret = qca8k_read(priv, QCA8K_REG_MASK_CTRL, &val);
> - if (ret < 0)
> - return -ENODEV;
> -
> - id = QCA8K_MASK_CTRL_DEVICE_ID(val);
> - if (id != data->id) {
> - dev_err(priv->dev, "Switch id detected %x but expected %x", id, data->id);
> - return -ENODEV;
> - }
> -
> - priv->switch_id = id;
> -
> - /* Save revision to communicate to the internal PHY driver */
> - priv->switch_revision = QCA8K_MASK_CTRL_REV_ID(val);
> -
> - return 0;
> -}
> -
> static int
> qca8k_sw_probe(struct mdio_device *mdiodev)
> {
> struct qca8k_priv *priv;
> - int ret;
>
> /* allocate the private data struct so that we can probe the switches
> * ID register
> @@ -2083,11 +2087,6 @@ qca8k_sw_probe(struct mdio_device *mdiodev)
> gpiod_set_value_cansleep(priv->reset_gpio, 0);
> }
>
> - /* Check the detected switch id */
> - ret = qca8k_read_switch_id(priv);
> - if (ret)
> - return ret;
> -
> priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL);
> if (!priv->ds)
> return -ENOMEM;
> --
> 2.32.0
>

\
 
 \ /
  Last update: 2021-11-19 02:03    [W:0.260 / U:0.848 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site