lkml.org 
[lkml]   [2021]   [Nov]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 3/3] drm/bridge: parade-ps8640: Perform full poweroff if poweron fails
From
Date


On 02.11.21 11:36, AngeloGioacchino Del Regno wrote:
> In function ps8640_bridge_poweron(), in case of a failure not relative
> to the regulators enablement, the code was disabling the regulators but
> the gpio changes that happened during the poweron sequence were not
> being reverted back to a clean poweroff state.
>
> Since it is expected that, when we enter ps8640_bridge_poweron(), the
> powerdown and reset GPIOs are both in active state exactly as they were
> left in the poweroff function before, we can simply call function
> __ps8640_bridge_poweroff() in the failure case, reverting every change
> that was done during the power on sequence.
>
> Of course it was chosen to call the poweroff function instead of adding
> code to revert the GPIO changes to the poweron one to avoid duplicating
> code, as we would be doing exactly what the poweroff function does.
>
> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Reviewed-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>

> ---
> drivers/gpu/drm/bridge/parade-ps8640.c | 11 +++++------
> 1 file changed, 5 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/parade-ps8640.c b/drivers/gpu/drm/bridge/parade-ps8640.c
> index 41f5d511d516..ef1b51d8b676 100644
> --- a/drivers/gpu/drm/bridge/parade-ps8640.c
> +++ b/drivers/gpu/drm/bridge/parade-ps8640.c
> @@ -344,7 +344,7 @@ static int ps8640_bridge_poweron(struct ps8640 *ps_bridge)
>
> if (ret < 0) {
> DRM_ERROR("failed read PAGE2_GPIO_H: %d\n", ret);
> - goto err_regulators_disable;
> + goto err_poweroff;
> }
>
> msleep(50);
> @@ -360,23 +360,22 @@ static int ps8640_bridge_poweron(struct ps8640 *ps_bridge)
> ret = regmap_update_bits(map, PAGE2_MCS_EN, MCS_EN, 0);
> if (ret < 0) {
> DRM_ERROR("failed write PAGE2_MCS_EN: %d\n", ret);
> - goto err_regulators_disable;
> + goto err_poweroff;
> }
>
> /* Switch access edp panel's edid through i2c */
> ret = regmap_write(map, PAGE2_I2C_BYPASS, I2C_BYPASS_EN);
> if (ret < 0) {
> DRM_ERROR("failed write PAGE2_I2C_BYPASS: %d\n", ret);
> - goto err_regulators_disable;
> + goto err_poweroff;
> }
>
> ps_bridge->powered = true;
>
> return 0;
>
> -err_regulators_disable:
> - regulator_bulk_disable(ARRAY_SIZE(ps_bridge->supplies),
> - ps_bridge->supplies);
> +err_poweroff:
> + __ps8640_bridge_poweroff(ps_bridge);
>
> return ret;
> }
>

\
 
 \ /
  Last update: 2021-11-10 13:49    [W:0.059 / U:0.456 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site