lkml.org 
[lkml]   [2021]   [Nov]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v4 5/8] phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver
Date
Hi Tim and Richard

On Mon, 2021-11-01 at 10:13 -0700, Tim Harvey wrote:
> On Mon, Nov 1, 2021 at 1:19 AM Richard Zhu <hongxing.zhu@nxp.com> wrote:
> >
> > > -----Original Message-----
> > > From: Tim Harvey <tharvey@gateworks.com>
> > > Sent: Saturday, October 30, 2021 1:45 AM
> > > To: Richard Zhu <hongxing.zhu@nxp.com>; Marcel Ziswiler
> > > <marcel.ziswiler@toradex.com>
> > > Cc: kishon@ti.com; vkoul@kernel.org; robh@kernel.org;
> > > l.stach@pengutronix.de; shawnguo@kernel.org;
> > > galak@kernel.crashing.org; linux-phy@lists.infradead.org;
> > > linux-arm-kernel@lists.infradead.org; kernel@pengutronix.de;
> > > devicetree@vger.kernel.org; linux-kernel@vger.kernel.org; dl-linux-imx
> > > <linux-imx@nxp.com>
> > > Subject: Re: [PATCH v4 5/8] phy: freescale: pcie: Initialize the imx8 pcie
> > > standalone phy driver
> > >
> > > On Fri, Oct 29, 2021 at 1:45 AM Richard Zhu <hongxing.zhu@nxp.com>
> > > wrote:
> > > >
> > > >
> > > > > -----Original Message-----
> > > > > From: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > > > > Sent: Friday, October 29, 2021 4:13 PM
> > > > > To: kishon@ti.com; vkoul@kernel.org; robh@kernel.org;
> > > > > l.stach@pengutronix.de; shawnguo@kernel.org;
> > > tharvey@gateworks.com;
> > > > > galak@kernel.crashing.org; Richard Zhu <hongxing.zhu@nxp.com>
> > > > > Cc: linux-phy@lists.infradead.org;
> > > > > linux-arm-kernel@lists.infradead.org;
> > > > > kernel@pengutronix.de; devicetree@vger.kernel.org;
> > > > > linux-kernel@vger.kernel.org; dl-linux-imx <linux-imx@nxp.com>
> > > > > Subject: Re: [PATCH v4 5/8] phy: freescale: pcie: Initialize the
> > > > > imx8 pcie standalone phy driver
> > > > >
> > > > > On Thu, 2021-10-28 at 15:27 +0800, Richard Zhu wrote:
> > > > > > Add the standalone i.MX8 PCIe PHY driver.
> > > > > >
> > > > > > Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
> > > > > > Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
> > > > >
> > > > > Unfortunately, this version no longer works for our
> > > > > IMX8_PCIE_REFCLK_PAD_OUTPUT use-case. Further comments in-
> > > lined
> > > > > below.
> > > > >
> > > > [Richard Zhu] Sorry to hear about that. Then, it seems that this bit
> > > > should be  set anyway.
> > > > It's hard to understand this bit refer to the RM document. Sigh ☹.
> > > > Would set the AUX_EN bit later.
> > > >
> > > > > > ---
> > > > > >  drivers/phy/freescale/Kconfig              |   9 +
> > > > > >  drivers/phy/freescale/Makefile             |   1 +
> > > > > >  drivers/phy/freescale/phy-fsl-imx8m-pcie.c | 234
> > > > > > +++++++++++++++++++++
> > > > > >  3 files changed, 244 insertions(+)  create mode 100644
> > > > > > drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > > > > >
> > > > > > diff --git a/drivers/phy/freescale/Kconfig
> > > > > > b/drivers/phy/freescale/Kconfig index 320630ffe3cd..de9ee7020f76
> > > > > > 100644
> > > > > > --- a/drivers/phy/freescale/Kconfig
> > > > > > +++ b/drivers/phy/freescale/Kconfig
> > > > > > @@ -14,3 +14,12 @@ config PHY_MIXEL_MIPI_DPHY
> > > > > >         help
> > > > > >           Enable this to add support for the Mixel DSI PHY as
> > > > > found
> > > > > >           on NXP's i.MX8 family of SOCs.
> > > > > > +
> > > > > > +config PHY_FSL_IMX8M_PCIE
> > > > > > +       tristate "Freescale i.MX8 PCIE PHY"
> > > > >
> > > > > Above description is missing the M as in i.MX 8M.
> > > > [Richard Zhu] Okay, would be added later.
> > > > Thanks.
> > > >
> > > > >
> > > > > > +       depends on OF && HAS_IOMEM
> > > > > > +       select GENERIC_PHY
> > > > > > +       default ARCH_MXC && ARM64
> > > > > > +       help
> > > > > > +         Enable this to add support for the PCIE PHY as found on
> > > > > > +         i.MX8M family of SOCs.
> > > > > > diff --git a/drivers/phy/freescale/Makefile
> > > > > > b/drivers/phy/freescale/Makefile index
> > > 1d02e3869b45..55d07c742ab0
> > > > > > 100644
> > > > > > --- a/drivers/phy/freescale/Makefile
> > > > > > +++ b/drivers/phy/freescale/Makefile
> > > > > > @@ -1,3 +1,4 @@
> > > > > >  # SPDX-License-Identifier: GPL-2.0-only
> > > > > >  obj-$(CONFIG_PHY_FSL_IMX8MQ_USB)       +=
> > > > > phy-fsl-imx8mq-usb.o
> > > > > >  obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY)      +=
> > > > > phy-fsl-imx8-mipi-dphy.o
> > > > > > +obj-$(CONFIG_PHY_FSL_IMX8M_PCIE)       +=
> > > > > phy-fsl-imx8m-pcie.o
> > > > > > diff --git a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > > > > > b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > > > > > new file mode 100644
> > > > > > index 000000000000..4b4402eaddcc
> > > > > > --- /dev/null
> > > > > > +++ b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> > > > > > @@ -0,0 +1,234 @@
> > > > > > +// SPDX-License-Identifier: GPL-2.0+
> > > > > > +/*
> > > > > > + * Copyright 2021 NXP
> > > > > > + */
> > > > > > +
> > > > > > +#include <linux/clk.h>
> > > > > > +#include <linux/io.h>
> > > > > > +#include <linux/iopoll.h>
> > > > > > +#include <linux/delay.h>
> > > > > > +#include <linux/mfd/syscon.h>
> > > > > > +#include <linux/mfd/syscon/imx7-iomuxc-gpr.h>
> > > > > > +#include <linux/module.h>
> > > > > > +#include <linux/phy/phy.h>
> > > > > > +#include <linux/platform_device.h> #include <linux/regmap.h>
> > > > > > +#include <linux/reset.h> #include
> > > > > > +<dt-bindings/phy/phy-imx8-pcie.h>
> > > > > > +
> > > > > > +#define IMX8MM_PCIE_PHY_CMN_REG061     0x184 #define
> > > > > > +ANA_PLL_CLK_OUT_TO_EXT_IO_EN  BIT(0) #define
> > > > > > +IMX8MM_PCIE_PHY_CMN_REG062     0x188 #define
> > > > > > +ANA_PLL_CLK_OUT_TO_EXT_IO_SEL BIT(3) #define
> > > > > > +IMX8MM_PCIE_PHY_CMN_REG063     0x18C #define
> > > > > > +AUX_PLL_REFCLK_SEL_SYS_PLL    GENMASK(7, 6) #define
> > > > > > +IMX8MM_PCIE_PHY_CMN_REG064     0x190
> > > > > #define  ANA_AUX_RX_TX_SEL_TX
> > > > > > +BIT(7)
> > > > > #define  ANA_AUX_RX_TERM_GND_EN                BIT(3)
> > > > > #define
> > > > > > +ANA_AUX_TX_TERM               BIT(2) #define
> > > > > > +IMX8MM_PCIE_PHY_CMN_REG065     0x194
> > > > > #define  ANA_AUX_RX_TERM
> > > > > > +(BIT(7) | BIT(4))
> > > > > #define  ANA_AUX_TX_LVL
> > > > > > +GENMASK(3, 0) #define
> > > > > IMX8MM_PCIE_PHY_CMN_REG75      0x1D4 #define
> > > > > > +PCIE_PHY_CMN_REG75_PLL_DONE   0x3 #define
> > > > > PCIE_PHY_TRSV_REG5
> > > > > > +0x414 #define  PCIE_PHY_TRSV_REG5_GEN1_DEEMP 0x2D
> > > #define
> > > > > > +PCIE_PHY_TRSV_REG6             0x418 #define
> > > > > > +PCIE_PHY_TRSV_REG6_GEN2_DEEMP 0xF
> > > > > > +
> > > > > > +#define IMX8MM_GPR_PCIE_REF_CLK_SEL    GENMASK(25, 24)
> > > > > #define
> > > > > > +IMX8MM_GPR_PCIE_REF_CLK_PLL
> > > > > > +FIELD_PREP(IMX8MM_GPR_PCIE_REF_CLK_SEL, 0x3) #define
> > > > > > +IMX8MM_GPR_PCIE_REF_CLK_EXT
> > > > > > +FIELD_PREP(IMX8MM_GPR_PCIE_REF_CLK_SEL, 0x2) #define
> > > > > > +IMX8MM_GPR_PCIE_AUX_EN         BIT(19) #define
> > > > > > +IMX8MM_GPR_PCIE_CMN_RST                BIT(18)
> > > > > #define
> > > > > > +IMX8MM_GPR_PCIE_POWER_OFF      BIT(17) #define
> > > > > IMX8MM_GPR_PCIE_SSC_EN
> > > > > > +BIT(16) #define
> > > > > IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE        BIT(9)
> > > > > > +
> > > > > > +struct imx8_pcie_phy {
> > > > > > +       void __iomem            *base;
> > > > > > +       struct clk              *clk;
> > > > > > +       struct phy              *phy;
> > > > > > +       struct regmap           *iomuxc_gpr;
> > > > > > +       struct reset_control    *reset;
> > > > > > +       u32                     refclk_pad_mode;
> > > > > > +       u32                     tx_deemph_gen1;
> > > > > > +       u32                     tx_deemph_gen2;
> > > > > > +       bool                    clkreq_unused; };
> > > > > > +
> > > > > > +static int imx8_pcie_phy_init(struct phy *phy) {
> > > > > > +       int ret;
> > > > > > +       u32 val, pad_mode;
> > > > > > +       struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > > > > > +
> > > > > > +       reset_control_assert(imx8_phy->reset);
> > > > > > +
> > > > > > +       pad_mode = imx8_phy->refclk_pad_mode;
> > > > > > +       /* Set AUX_EN_OVERRIDE 1'b0, when the CLKREQ# isn't
> > > > > hooked */
> > > > > > +       regmap_update_bits(imx8_phy->iomuxc_gpr,
> > > > > IOMUXC_GPR14,
> > > > > >
> > > > > +                          IMX8MM_GPR_PCIE_AUX_EN_
> > > > > OVERRIDE,
> > > > > > +                          imx8_phy->clkreq_unused ?
> > > > > > +                          0 :
> > > > > IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE);
> > > > > > +       regmap_update_bits(imx8_phy->iomuxc_gpr,
> > > > > IOMUXC_GPR14,
> > > > > > +                          IMX8MM_GPR_PCIE_AUX_EN,
> > > > > > +                          pad_mode ==
> > > > > IMX8_PCIE_REFCLK_PAD_INPUT ?
> > > > > > +                          IMX8MM_GPR_PCIE_AUX_EN :
> > > > > 0);
> > > > >
> > > > > V3 had IMX8MM_GPR_PCIE_AUX_EN always enabled. Turns out V4
> > > stopped
> > > > > working for our output use-case as it only enables it for the input
> > > > > use-case. If I enable this one always it starts working again.
> > > > [Richard Zhu] See my comment above.
> > > > Sorry to bring the regression on your board.
> > > >
> > >
> > > Marcel,
> > >
> > > Your board does not use an external clk, but does it hook up CLKREQ#
> > > from the socket to either I2C4_SCL or UART4_RXD and pin muxed as
> > > such?
> > >
> > > For my board that uses an external clk and does not connect CLKREQ# to
> > > the IMX8MM I need to disable that bit. As Richard says we have invalid
> > > documentation for these bits unfortunately which is not helping.
> > >
> > > Richard, when we do figure out proper documentation for these bits I
> > > suggest you also add a comment block right above their #defines in the
> > > phy driver with the correct documentation to avoid future confusion.
> > > NXP has had so many mistakes in the various IMX8M RM's and I fear they
> > > will never get fixed.
> > [Richard Zhu] Hi Tim:
> > I took look at the validation codes, and found that the AUX_EN is always
> >  set to be 1b'1. Whatever the reference clock mode is selected.
> > I'm sending a query email to design team, but I'm not sure I can get response
> > in time.
> > Can you help to take a double tests at your board when AUX_EN(bit19 of GPR14)
> > is set to be 1b'1 firstly?
> > Thanks in advanced.
> >
>
> Richard and Marcel,
>
> I apologize, my mistake I was referring to GPR14 bit 9 and not bit19
> in my testing above.
>
> I tested leaving bit 9 set and this still works on my boards with ext
> clk and no CLKREQ# as well as imx8mm-evk with ext clk and CLKREQ#.
>
> So the change on top of your v4 would be:
>
> diff --git a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> index 4b4402eaddcc..003f575b36f0 100644
> --- a/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> +++ b/drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> @@ -73,8 +73,7 @@ static int imx8_pcie_phy_init(struct phy *phy)
>                            0 : IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE);
>         regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
>                            IMX8MM_GPR_PCIE_AUX_EN,
> -                          pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT ?
> -                          IMX8MM_GPR_PCIE_AUX_EN : 0);
> +                          IMX8MM_GPR_PCIE_AUX_EN);
>         regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
>                            IMX8MM_GPR_PCIE_POWER_OFF, 0);
>         regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
>
> Marcel, does this look right for your board?

Yes, that is exactly how I run it now. Thanks!

> Best regards,
>
> Tim

Cheers

Marcel
\
 
 \ /
  Last update: 2021-11-02 00:53    [W:0.133 / U:1.308 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site