lkml.org 
[lkml]   [2021]   [Oct]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] Make top/rear speaker, mute and micmute leds work on HP x360 14-ea000 laptops that use Realtek 245 codec
On Fri, 29 Oct 2021 17:43:13 +0200,
Jonathan Clarke wrote:
>
> BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210633
> Signed-off-by: Jonathan Clarke <jonathan.a.clarke@gmail.com>

Could you give more descriptions? The patch isn't trivial at all, and
it needs more explanations.

> ---
> sound/pci/hda/patch_realtek.c | 46 +++++++++++++++++++++++++++++++++++
> 1 file changed, 46 insertions(+)
>
> diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c
> index 22d27b12c..e3c6d17ea 100644
> --- a/sound/pci/hda/patch_realtek.c
> +++ b/sound/pci/hda/patch_realtek.c
> @@ -4409,6 +4409,13 @@ static void alc245_fixup_hp_x360_amp(struct hda_codec *codec,
> case HDA_FIXUP_ACT_PRE_PROBE:
> spec->gpio_mask |= 0x01;
> spec->gpio_dir |= 0x01;
> +
> + /* use only amp at 0x02 for bottom(front) speaker,
> + * otherwise it is set to use 0x02,0x03,0x06 and when used in conjunction
> + * with top(rear) speaker 0x14, gets locked at full volume */
> + static const hda_nid_t conn1[] = { 0x02 };
> + snd_hda_override_conn_list(codec, 0x17, ARRAY_SIZE(conn1), conn1);
> +
> break;
> case HDA_FIXUP_ACT_INIT:
> /* need to toggle GPIO to enable the amp */
> @@ -4503,6 +4510,26 @@ static void alc236_fixup_hp_mute_led_coefbit(struct hda_codec *codec,
> }
> }
>
> +static void alc245_fixup_hp_x360_mute_leds(struct hda_codec *codec,
> + const struct hda_fixup *fix, int action)
> +{
> + struct alc_spec *spec = codec->spec;
> + if (action == HDA_FIXUP_ACT_PRE_PROBE) {
> + /* mic mute is set via gpio 0x04 */
> + spec->micmute_led_polarity = 1;
> + codec->power_filter = led_power_filter;
> + alc_fixup_hp_gpio_led(codec, action, 0x00, 0x04);
> +
> + /* output mute is set via SET_COEF_INDEX,SET_PROC_COEF */
> + spec->mute_led_polarity = 0;
> + spec->mute_led_coef.idx = 0x0b;
> + spec->mute_led_coef.mask = 0xffff;
> + spec->mute_led_coef.on = 0xa02f;
> + spec->mute_led_coef.off = 0x7774;
> + snd_hda_gen_add_mute_led_cdev(codec, coef_mute_led_set);

I guess this COEF isn't only about mute-LED but actually does mute the
output? IIRC, the bit 0x08 corresponds to the LED. If so, it's
better to split. Basically this snd_hda_gen_add_mute_led_cdev() and
mute_led_coef stuff are only for the mute LED control. e.g. you can
change the mute LED independently via sysfs.


thanks,

Takashi

\
 
 \ /
  Last update: 2021-10-30 12:01    [W:0.100 / U:0.548 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site