lkml.org 
[lkml]   [2021]   [Oct]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 1/2] mmc: core: adjust polling interval for CMD1
On Fri, 22 Oct 2021 at 08:39, Huijin Park <huijin.park@samsung.com> wrote:
>
> In mmc_send_op_cond(), loops are continuously performed at the same
> interval of 10 ms. However the behaviour is not good for some eMMC
> which can be out from a busy state earlier than 10 ms if normal.
>
> Therefore, this patch adjusts the waiting interval time. The interval
> time starts at 1 ms, but doubles until the range reaches 10 ms for
> each loop.
>
> The reason for adjusting the interval time is that it is important
> to reduce the eMMC initialization time, especially in devices that
> use eMMC as rootfs.
>
> Test log(eMMC:KLM8G1GETF-B041):
>
> before: 12 ms (0.439407 - 0.427186)
> [0.419407] mmc0: starting CMD0 arg 00000000 flags 000000c0
> [0.422652] mmc0: starting CMD1 arg 00000000 flags 000000e1
> [0.424270] mmc0: starting CMD0 arg 00000000 flags 000000c0
> [0.427186] mmc0: starting CMD1 arg 40000080 flags 000000e1<-start
> [0.439407] mmc0: starting CMD1 arg 40000080 flags 000000e1<-finish
> [0.439721] mmc0: starting CMD2 arg 00000000 flags 00000007
>
> after: 4 ms (0.431725 - 0.427352)
> [0.419575] mmc0: starting CMD0 arg 00000000 flags 000000c0
> [0.422819] mmc0: starting CMD1 arg 00000000 flags 000000e1
> [0.424435] mmc0: starting CMD0 arg 00000000 flags 000000c0
> [0.427352] mmc0: starting CMD1 arg 40000080 flags 000000e1<-start
> [0.428913] mmc0: starting CMD1 arg 40000080 flags 000000e1
> [0.431725] mmc0: starting CMD1 arg 40000080 flags 000000e1<-finish
> [0.432038] mmc0: starting CMD2 arg 00000000 flags 00000007
>
> Signed-off-by: Huijin Park <huijin.park@samsung.com>
>
> diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c
> index 0c54858e89c0..61b4ffdc89ce 100644
> --- a/drivers/mmc/core/mmc_ops.c
> +++ b/drivers/mmc/core/mmc_ops.c
> @@ -177,6 +177,7 @@ int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr)
> {
> struct mmc_command cmd = {};
> int i, err = 0;
> + int interval = 1, interval_max = 10;
>
> cmd.opcode = MMC_SEND_OP_COND;
> cmd.arg = mmc_host_is_spi(host) ? 0 : ocr;
> @@ -198,7 +199,9 @@ int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr)
>
> err = -ETIMEDOUT;
>
> - mmc_delay(10);
> + mmc_delay(interval);
> + if (interval < interval_max)
> + interval = min(interval * 2, interval_max);

It looks like we should be able to replace the above polling loop with
__mmc_poll_for_busy(). We would need a callback function and a
callback data, specific for CMD1, but that looks far better to me, if
we can get that to work.

Would you mind having a look?

>
> /*
> * According to eMMC specification v5.1 section 6.4.3, we

Kind regards
Uffe

\
 
 \ /
  Last update: 2021-10-26 18:56    [W:0.050 / U:0.472 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site