lkml.org 
[lkml]   [2021]   [Oct]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 7/8] tty: serial: samsung_tty: Support runtime PM
Date
This allows idle UART devices to be suspended using the standard
runtime-PM framework. The logic is modeled after stm32-usart.

Signed-off-by: Hector Martin <marcan@marcan.st>
---
drivers/tty/serial/samsung_tty.c | 93 ++++++++++++++++++++------------
1 file changed, 59 insertions(+), 34 deletions(-)

diff --git a/drivers/tty/serial/samsung_tty.c b/drivers/tty/serial/samsung_tty.c
index e2f49863e9c2..8b6ca6ec71ca 100644
--- a/drivers/tty/serial/samsung_tty.c
+++ b/drivers/tty/serial/samsung_tty.c
@@ -40,6 +40,7 @@
#include <linux/clk.h>
#include <linux/cpufreq.h>
#include <linux/of.h>
+#include <linux/pm_runtime.h>
#include <asm/irq.h>

/* UART name and device definitions */
@@ -1381,31 +1382,49 @@ static void exynos_usi_init(struct uart_port *port)

/* power power management control */

-static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level,
- unsigned int old)
+static int __maybe_unused s3c24xx_serial_runtime_suspend(struct device *dev)
{
+ struct uart_port *port = dev_get_drvdata(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
int timeout = 10000;

- ourport->pm_level = level;
+ while (--timeout && !s3c24xx_serial_txempty_nofifo(port))
+ udelay(100);

- switch (level) {
- case 3:
- while (--timeout && !s3c24xx_serial_txempty_nofifo(port))
- udelay(100);
+ if (!IS_ERR(ourport->baudclk))
+ clk_disable_unprepare(ourport->baudclk);

- if (!IS_ERR(ourport->baudclk))
- clk_disable_unprepare(ourport->baudclk);
+ clk_disable_unprepare(ourport->clk);
+ return 0;
+};

- clk_disable_unprepare(ourport->clk);
- break;
+static int __maybe_unused s3c24xx_serial_runtime_resume(struct device *dev)
+{
+ struct uart_port *port = dev_get_drvdata(dev);
+ struct s3c24xx_uart_port *ourport = to_ourport(port);

- case 0:
- clk_prepare_enable(ourport->clk);
+ clk_prepare_enable(ourport->clk);

- if (!IS_ERR(ourport->baudclk))
- clk_prepare_enable(ourport->baudclk);
+ if (!IS_ERR(ourport->baudclk))
+ clk_prepare_enable(ourport->baudclk);
+ return 0;
+};

+static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level,
+ unsigned int old)
+{
+ struct s3c24xx_uart_port *ourport = to_ourport(port);
+
+ ourport->pm_level = level;
+
+ switch (level) {
+ case UART_PM_STATE_OFF:
+ pm_runtime_mark_last_busy(port->dev);
+ pm_runtime_put_sync(port->dev);
+ break;
+
+ case UART_PM_STATE_ON:
+ pm_runtime_get_sync(port->dev);
exynos_usi_init(port);
break;
default:
@@ -2282,18 +2301,15 @@ static int s3c24xx_serial_probe(struct platform_device *pdev)
}
}

+ pm_runtime_get_noresume(&pdev->dev);
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+
dev_dbg(&pdev->dev, "%s: adding port\n", __func__);
uart_add_one_port(&s3c24xx_uart_drv, &ourport->port);
platform_set_drvdata(pdev, &ourport->port);

- /*
- * Deactivate the clock enabled in s3c24xx_serial_init_port here,
- * so that a potential re-enablement through the pm-callback overlaps
- * and keeps the clock enabled in this case.
- */
- clk_disable_unprepare(ourport->clk);
- if (!IS_ERR(ourport->baudclk))
- clk_disable_unprepare(ourport->baudclk);
+ pm_runtime_put_sync(&pdev->dev);

ret = s3c24xx_serial_cpufreq_register(ourport);
if (ret < 0)
@@ -2307,10 +2323,21 @@ static int s3c24xx_serial_probe(struct platform_device *pdev)
static int s3c24xx_serial_remove(struct platform_device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
+ struct s3c24xx_uart_port *ourport = to_ourport(port);

if (port) {
+ pm_runtime_get_sync(&dev->dev);
+
s3c24xx_serial_cpufreq_deregister(to_ourport(port));
uart_remove_one_port(&s3c24xx_uart_drv, port);
+
+ clk_disable_unprepare(ourport->clk);
+ if (!IS_ERR(ourport->baudclk))
+ clk_disable_unprepare(ourport->baudclk);
+
+ pm_runtime_disable(&dev->dev);
+ pm_runtime_set_suspended(&dev->dev);
+ pm_runtime_put_noidle(&dev->dev);
}

uart_unregister_driver(&s3c24xx_uart_drv);
@@ -2319,8 +2346,8 @@ static int s3c24xx_serial_remove(struct platform_device *dev)
}

/* UART power management code */
-#ifdef CONFIG_PM_SLEEP
-static int s3c24xx_serial_suspend(struct device *dev)
+
+static int __maybe_unused s3c24xx_serial_suspend(struct device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);

@@ -2330,7 +2357,7 @@ static int s3c24xx_serial_suspend(struct device *dev)
return 0;
}

-static int s3c24xx_serial_resume(struct device *dev)
+static int __maybe_unused s3c24xx_serial_resume(struct device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
@@ -2350,7 +2377,7 @@ static int s3c24xx_serial_resume(struct device *dev)
return 0;
}

-static int s3c24xx_serial_resume_noirq(struct device *dev)
+static int __maybe_unused s3c24xx_serial_resume_noirq(struct device *dev)
{
struct uart_port *port = s3c24xx_dev_to_port(dev);
struct s3c24xx_uart_port *ourport = to_ourport(port);
@@ -2420,16 +2447,14 @@ static int s3c24xx_serial_resume_noirq(struct device *dev)
}

static const struct dev_pm_ops s3c24xx_serial_pm_ops = {
+#ifdef CONFIG_PM_SLEEP
.suspend = s3c24xx_serial_suspend,
.resume = s3c24xx_serial_resume,
.resume_noirq = s3c24xx_serial_resume_noirq,
+#endif
+ SET_RUNTIME_PM_OPS(s3c24xx_serial_runtime_suspend,
+ s3c24xx_serial_runtime_resume, NULL)
};
-#define SERIAL_SAMSUNG_PM_OPS (&s3c24xx_serial_pm_ops)
-
-#else /* !CONFIG_PM_SLEEP */
-
-#define SERIAL_SAMSUNG_PM_OPS NULL
-#endif /* CONFIG_PM_SLEEP */

/* Console code */

@@ -2924,7 +2949,7 @@ static struct platform_driver samsung_serial_driver = {
.id_table = s3c24xx_serial_driver_ids,
.driver = {
.name = "samsung-uart",
- .pm = SERIAL_SAMSUNG_PM_OPS,
+ .pm = &s3c24xx_serial_pm_ops,
.of_match_table = of_match_ptr(s3c24xx_uart_dt_match),
},
};
--
2.33.0
\
 
 \ /
  Last update: 2021-10-25 16:49    [W:0.091 / U:0.904 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site