lkml.org 
[lkml]   [2021]   [Oct]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 4/5] driver core: inhibit automatic driver binding on reserved devices
On Mon, Oct 25, 2021 at 10:54:21AM -0500, Patrick Williams wrote:
> On Mon, Oct 25, 2021 at 04:09:59PM +0200, Greg Kroah-Hartman wrote:
> > On Mon, Oct 25, 2021 at 09:02:40AM -0500, Patrick Williams wrote:
> > > On Mon, Oct 25, 2021 at 03:34:05PM +0200, Greg Kroah-Hartman wrote:
> > > > On Mon, Oct 25, 2021 at 08:20:05AM -0500, Patrick Williams wrote:
> > > > I think "it" is "something needs to be the moderator between the two
> > > > operating systems". What is the external entity that handles the
> > > > switching between the two?
> > >
> > > Ah, ok.
> > >
> > > Those usually end up being system / device specific. In the case of the BIOS
> > > flash, most designs I've seen use a SPI mux between the BMC and the host
> > > processor or IO hub (PCH on Xeons). The BMC has a GPIO to control the mux.
> > >
> > > As far as state, the BMC on start-up will go through a set of discovery code to
> > > figure out where it left the system prior to getting reset. That involves
> > > looking at the power subsystem and usually doing some kind of query to the host
> > > to see if it is alive. These queries are mostly system / host-processor design
> > > specific. I've seen anything from an IPMI/IPMB message alert from the BMC to
> > > the BIOS to ask "are you alive" to reading host processor state over JTAG to
> > > figure out if the processors are "making progress".
> >
> > But which processor is "in control" here over the hardware?
>
> The BMC. It owns the GPIO that controls the SPI mux.
>
> But, the BMC is responsible for doing all operations in a way that doesn't mess
> up the running host processor(s). Pulling away the SPI flash containing the
> BIOS code at an incorrect time might do that.
>
> > What method
> > is used to pass the device from one CPU to another from a logical point
> > of view?
>
> The state of the server as a whole is determined and maintained by the BMC. I'm
> simplifying here a bit but the operation "turn on the host processors" implies
> "the host processors will access the BIOS" so the BMC must ensure "SPI mux is
> switched towards the host" before "turn on the host processors".
>
> > Sounds like it is another driver that needs to handle all of
> > this, so why not have that be the one that adds/removes the devices
> > under control here?
>
> If what you're describing is moving all of the state control logic into the
> kernel, I don't think that is feasible. For some systems it would mean moving
> yet another entire IPMI stack into the kernel tree. On others it might be
> somewhat simpler, but it is still a good amount of code. We could probably
> write up more details on the scope of this.
>
> If what you're describing is a small driver, similar to the board support
> drivers that were used before the device tree, that instantiates subordinate
> devices it doesn't seem like an unreasonable alternative to DT overlays to me
> (for whatever my limited kernel contribution experience counts for).
>

Something has to be here doing the mediation between the two processors
and keeping things straight as to what processor is handling the
hardware when. I suggest you focus on that first...

Good luck!

greg k-h

\
 
 \ /
  Last update: 2021-10-25 20:37    [W:0.724 / U:0.864 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site