lkml.org 
[lkml]   [2021]   [Oct]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 06/11] drm/msm/disp/dpu1: Don't use DSC with mode_3d
From
Date
On 25/10/2021 19:10, Vinod Koul wrote:
> On 25-10-21, 17:40, Dmitry Baryshkov wrote:
>> On 20/10/2021 09:57, Vinod Koul wrote:
>>> On 14-10-21, 16:50, Dmitry Baryshkov wrote:
>>>> On 14/10/2021 16:41, Dmitry Baryshkov wrote:
>>>>> On 07/10/2021 10:08, Vinod Koul wrote:
>
>>>>>> diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h
>>>>>> b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h
>>>>>> index 806c171e5df2..5dfac5994bd4 100644
>>>>>> --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h
>>>>>> +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_hw_ctl.h
>>>>>> @@ -39,6 +39,7 @@ struct dpu_hw_stage_cfg {
>>>>>>    * @mode_3d:               3d mux configuration
>>>>>>    * @merge_3d:              3d merge block used
>>>>>>    * @intf_mode_sel:         Interface mode, cmd / vid
>>>>>> + * @dsc:                   DSC BIT masks
>>>>>>    * @stream_sel:            Stream selection for multi-stream interfaces
>>>>>>    */
>>>>>>   struct dpu_hw_intf_cfg {
>>>>>> @@ -46,6 +47,7 @@ struct dpu_hw_intf_cfg {
>>>>>>       enum dpu_3d_blend_mode mode_3d;
>>>>>>       enum dpu_merge_3d merge_3d;
>>>>>>       enum dpu_ctl_mode_sel intf_mode_sel;
>>>>>> +    unsigned int dsc;
>>>>
>>>> I think this should be:
>>>> enum dpu_dsc dsc[MAX_DSCS];
>>>> unsigned int num_dsc;
>>>
>>> hmmm, how do we go about getting the num_dsc value here.
>>> dpu_encoder_phys does not know about that..
>>
>> dpu_encoder_get_topology() can decide whether to use DSC or not and then set
>> num_dsc. For now it will always set 2 if we are using DSC at all, but let's
>> keep the decision in a single place rather than having it scattered all over
>> the driver.
>
> Yes agree, but dpu_encoder_get_topology() is private to encoder. Am not
> sure how best to propagate the info into the hw_intf_cfg?

Let dpu_encoder_get_topology() set num_dscs to 2 and merge_3d to 0 if
the encoder has DSC information and to 0 otherwise. This will cover all
topologies that we care about for now.

Regarding getting the DSC config. Currently you use single priv->dsc
pointer, which works for the simple case of single DSI output, but will
break as soon as somebody has DSC DSI + DP config. Either we can
introduce the array of DSC configs, or we can add a DSI-specific
msm_dsi_get_dsc_config(), which will be later paired with the
corresponding displayport function.

--
With best wishes
Dmitry

\
 
 \ /
  Last update: 2021-10-25 20:34    [W:2.120 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site