lkml.org 
[lkml]   [2021]   [Oct]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 09/16] reset: starfive-jh7100: Add StarFive JH7100 reset driver
On Fri, 22 Oct 2021 at 17:25, Andy Shevchenko <andy.shevchenko@gmail.com> wrote:
> On Fri, Oct 22, 2021 at 5:56 PM Emil Renner Berthing <kernel@esmil.dk> wrote:
> > On Fri, 22 Oct 2021 at 16:50, Andy Shevchenko <andy.shevchenko@gmail.com> wrote:
> > > On Fri, Oct 22, 2021 at 5:25 PM Emil Renner Berthing <kernel@esmil.dk> wrote:
> > > > On Fri, 22 Oct 2021 at 15:39, Andy Shevchenko <andy.shevchenko@gmail.com> wrote:
> > > > > On Fri, Oct 22, 2021 at 4:35 PM Emil Renner Berthing <kernel@esmil.dk> wrote:
> > > > > > On Fri, 22 Oct 2021 at 14:56, Andy Shevchenko <andy.shevchenko@gmail.com> wrote:
> > > > > > > On Thu, Oct 21, 2021 at 8:43 PM Emil Renner Berthing <kernel@esmil.dk> wrote:
>
> ...
>
> > > > > > > Why all these ugly % 32 against constants?
> > > > > >
> > > > > > Because the JH7100_RST_ values goes higher than 31. There is a
> > > > > > BIT_MASK macro, but that does % BITS_PER_LONG and this is a 64bit
> > > > > > machine.
> > > > >
> > > > > And? It's exactly what you have to use!
> > > >
> > > > So you want me to use an unsigned long array or DECLARE_BITMAP and
> > > > juggle two different index and bit offsets?
> > >
> > > What are the offsets of those status registers?
> > > AFAICS they are sequential 4 32-bit registers.
> >
> > That's right, but we're on a 64bit machine, so DECLARE_BITMAP will
> > give us an unsigned long array that doesn't match that.
>
> I didn't get it, sorry.
> You will have a bitmap array which you will split to 32-bit values.
> What you will probably need is to move xgpio_get_value32() and void
> xgpio_set_value32() to the one of bitmap related headers (look for
> bitmap_get_value8() and friends).
>
> > > So bitmap is exactly what is suitable here, you are right!
> > > See gpio-xilinx and gpio-pca953x on how to use bitmaps in the GPIO drivers.
> >
> > None of them has a pre-initialized const DECLARE_BITMAP, so they don't
> > have to deal with the 4 vs. 2 commas problem.
>
> I believe it's well possible to refactor this to look much better with
> bitmaps (as it represents the hardware very well).

Right, but how exactly? This works on on 64bit, but not with 32bit COMPILE_TEST:

static const DECLARE_BITMAP(jh7100_reset_asserted, JH7100_RSTN_END) = {
/* STATUS0 register */
BIT_MASK(JH7100_RST_U74) |
BIT_MASK(JH7100_RST_VP6_DRESET) |
BIT_MASK(JH7100_RST_VP6_BRESET) |
/* STATUS1 register */
BIT_MASK(JH7100_RST_HIFI4_DRESET) |
BIT_MASK(JH7100_RST_HIFI4_BRESET),
/* STATUS2 register */
BIT_MASK(JH7100_RST_E24) |
/* STATUS3 register */
0,
};


> > > > Also is there a macro for handling that we'd then need 4 commas on
> > > > 32bit COMPILE_TEST and 2 commas on 64bit?
> > > > If you have some other way in mind you'll have to be a lot more explicit again.
> > > >
> > > > The point of the jh7100_reset_asserted array is that it exactly
> > > > mirrors the values of the status registers when the lines are
> > > > asserted. Maybe writing it like this would be more explicit:
> > > >
> > > > static const u32 jh7100_reset_asserted[4] = {
> > > > /* STATUS0 register */
> > > > BIT(JH7100_RST_U74 % 32) |
> > > > BIT(JH7100_RST_VP6_DRESET % 32) |
> > > > BIT(JH7100_RST_VP6_BRESET % 32),
> > > > /* STATUS1 register */
> > > > BIT(JH7100_RST_HIFI4_DRESET % 32) |
> > > > BIT(JH7100_RST_HIFI4_BRESET % 32),
> > > > /* STATUS2 register */
> > > > BIT(JH7100_RST_E24 % 32),
> > > > /* STATUS3 register */
> > > > 0,
> > > > };
>
> --
> With Best Regards,
> Andy Shevchenko

\
 
 \ /
  Last update: 2021-10-22 17:40    [W:1.071 / U:0.152 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site