Messages in this thread | | | Subject | Re: [PATCH v4 00/20] Enable Qualcomm Crypto Engine on sm8250 | From | Thara Gopinath <> | Date | Wed, 20 Oct 2021 10:03:24 -0400 |
| |
On 10/13/21 6:55 AM, Bhupesh Sharma wrote: > Sorry for a delayed v4, but I have been caught up with some other > patches.
Hi Bhupesh,
If possible, please consider splitting this series into 2. One with changes required to support crypto driver on sm8250 and other with the generic fixes / fixing the dt-bindings et all. It would be easier to review as well
-- Warm Regards Thara (She/Her/Hers)
> > Changes since v3: > ================= > - v3 can be seen here: https://lore.kernel.org/linux-arm-msm/20210519143700.27392-1-bhupesh.sharma@linaro.org/ > - Dropped a couple of patches from v3, on basis of the review comments: > ~ [PATCH 13/17] crypto: qce: core: Make clocks optional > ~ [PATCH 15/17] crypto: qce: Convert the device found dev_dbg() to dev_info() > - Addressed review comments from Thara, Rob and Stephan Gerhold. > - Collect Reviewed-by from Rob and Thara on some of the patches from the > v3 patchset. > > Changes since v2: > ================= > - v2 can be seen here: https://lore.kernel.org/dmaengine/20210505213731.538612-1-bhupesh.sharma@linaro.org/ > - Drop a couple of patches from v1, which tried to address the defered > probing of qce driver in case bam dma driver is not yet probed. > Replace it instead with a single (simpler) patch [PATCH 16/17]. > - Convert bam dma and qce crypto dt-bindings to YAML. > - Addressed review comments from Thara, Bjorn, Vinod and Rob. > > Changes since v1: > ================= > - v1 can be seen here: https://lore.kernel.org/linux-arm-msm/20210310052503.3618486-1-bhupesh.sharma@linaro.org/ > - v1 did not work well as reported earlier by Dmitry, so v2 contains the following > changes/fixes: > ~ Enable the interconnect path b/w BAM DMA and main memory first > before trying to access the BAM DMA registers. > ~ Enable the interconnect path b/w qce crytpo and main memory first > before trying to access the qce crypto registers. > ~ Make sure to document the required and optional properties for both > BAM DMA and qce crypto drivers. > ~ Add a few debug related print messages in case the qce crypto driver > passes or fails to probe. > ~ Convert the qce crypto driver probe to a defered one in case the BAM DMA > or the interconnect driver(s) (needed on specific Qualcomm parts) are not > yet probed. > > Qualcomm crypto engine is also available on sm8250 SoC. > It supports hardware accelerated algorithms for encryption > and authentication. It also provides support for aes, des, 3des > encryption algorithms and sha1, sha256, hmac(sha1), hmac(sha256) > authentication algorithms. > > Tested the enabled crypto algorithms with cryptsetup test utilities > on sm8250-mtp and RB5 board (see [1]) and also with crypto self-tests, > including the fuzz tests (CONFIG_CRYPTO_MANAGER_EXTRA_TESTS=y). > > Note that this series is rebased on a SMMU related fix from Arnd applied > on either linus's tip of linux-next's tip (see [2]), without which > the sm8250 based boards fail to boot with the latest tip. > > [1]. https://linux.die.net/man/8/cryptsetup > [2]. https://lore.kernel.org/linux-arm-kernel/CAA8EJpoD4Th1tdwYQLnZur2oA0xX0LojSrNFLyJqdi6+rnB3YQ@mail.gmail.com/T/ > > Cc: Thara Gopinath <thara.gopinath@linaro.org> > Cc: Bjorn Andersson <bjorn.andersson@linaro.org> > Cc: Rob Herring <robh+dt@kernel.org> > > Bhupesh Sharma (17): > arm64/dts: qcom: Fix 'dma' & 'qcom,controlled-remotely' nodes in dts > arm64/dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' > property > arm64/dts: qcom: ipq6018: Remove unused 'iface_clk' property from > dma-controller node > dt-bindings: qcom-bam: Convert binding to YAML > dt-bindings: qcom-bam: Add 'interconnects' & 'interconnect-names' to > optional properties > dt-bindings: qcom-bam: Add 'iommus' to optional properties > dt-bindings: qcom-qce: Convert bindings to yaml > dt-bindings: qcom-qce: Add 'interconnects' and move 'clocks' to > optional properties > dt-bindings: qcom-qce: Add 'iommus' to optional properties > arm64/dts: qcom: sdm845: Use RPMH_CE_CLK macro directly > dt-bindings: crypto : Add new compatible strings for qcom-qce > arm64/dts: qcom: Use new compatibles for crypto nodes > crypto: qce: Add new compatibles for qce crypto driver > crypto: qce: Print a failure msg in case probe() fails > crypto: qce: Defer probing if BAM dma channel is not yet initialized > crypto: qce: Add 'sm8250-qce' compatible string check > arm64/dts: qcom: sm8250: Add dt entries to support crypto engine. > > Thara Gopinath (3): > dma: qcom: bam_dma: Add support to initialize interconnect path > crypto: qce: core: Add support to initialize interconnect path > crypto: qce: core: Make clocks optional > > .../devicetree/bindings/crypto/qcom-qce.yaml | 90 +++++++++++++++ > .../devicetree/bindings/dma/qcom_bam_dma.txt | 50 -------- > .../devicetree/bindings/dma/qcom_bam_dma.yaml | 107 ++++++++++++++++++ > arch/arm64/boot/dts/qcom/ipq6018.dtsi | 10 +- > arch/arm64/boot/dts/qcom/ipq8074.dtsi | 4 +- > arch/arm64/boot/dts/qcom/msm8996.dtsi | 4 +- > arch/arm64/boot/dts/qcom/msm8998.dtsi | 2 +- > arch/arm64/boot/dts/qcom/sdm845.dtsi | 10 +- > arch/arm64/boot/dts/qcom/sm8250.dtsi | 28 +++++ > drivers/crypto/qce/core.c | 66 +++++++---- > drivers/crypto/qce/core.h | 1 + > drivers/dma/qcom/bam_dma.c | 16 ++- > 12 files changed, 302 insertions(+), 86 deletions(-) > create mode 100644 Documentation/devicetree/bindings/crypto/qcom-qce.yaml > delete mode 100644 Documentation/devicetree/bindings/dma/qcom_bam_dma.txt > create mode 100644 Documentation/devicetree/bindings/dma/qcom_bam_dma.yaml >
| |