lkml.org 
[lkml]   [2021]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v11 1/4] HID: wacom_sys: Add support for flipping the data values
On Tue, Oct 19, 2021 at 3:42 AM Ping Cheng <pinglinux@gmail.com> wrote:
>
> Hi Alistair,
>
> On Sat, Oct 9, 2021, 4:44 AM Alistair Francis <alistair@alistair23.me> wrote:
>>
>> Add support to the Wacom HID device for flipping the values based on
>> device tree settings. This allows us to support devices where the panel
>> is installed in a different orientation, such as the reMarkable2.
>
>
> This device was designed for hid-generic driver, if it's not driven by wacom_i2c.c or an out of tree driver.
>
> wacom.ko doesn't support vid 0x2d1f devices.
>
> Nacked-by: Ping Cheng <Ping.Cheng@wacom.com>

Any ideas how to support the hardware then?

I can't use the wacom_i2c driver as the panel supports I2C HID. But I
can't use the I2C HID driver as I need the values flipped to support
the installed orientation.

Alistair

>
> Sorry about that,
> Ping
>
>> Signed-off-by: Alistair Francis <alistair@alistair23.me>
>> ---
>> .../bindings/input/hid-over-i2c.txt | 20 ++++++
>> drivers/hid/wacom_sys.c | 25 ++++++++
>> drivers/hid/wacom_wac.c | 61 +++++++++++++++++++
>> drivers/hid/wacom_wac.h | 13 ++++
>> 4 files changed, 119 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/input/hid-over-i2c.txt b/Documentation/devicetree/bindings/input/hid-over-i2c.txt
>> index c76bafaf98d2..16ebd7c46049 100644
>> --- a/Documentation/devicetree/bindings/input/hid-over-i2c.txt
>> +++ b/Documentation/devicetree/bindings/input/hid-over-i2c.txt
>> @@ -33,6 +33,26 @@ device-specific compatible properties, which should be used in addition to the
>> - post-power-on-delay-ms: time required by the device after enabling its regulators
>> or powering it on, before it is ready for communication.
>>
>> + flip-tilt-x:
>> + type: boolean
>> + description: Flip the tilt X values read from device
>> +
>> + flip-tilt-y:
>> + type: boolean
>> + description: Flip the tilt Y values read from device
>> +
>> + flip-pos-x:
>> + type: boolean
>> + description: Flip the X position values read from device
>> +
>> + flip-pos-y:
>> + type: boolean
>> + description: Flip the Y position values read from device
>> +
>> + flip-distance:
>> + type: boolean
>> + description: Flip the distance values read from device
>> +
>> Example:
>>
>> i2c-hid-dev@2c {
>> diff --git a/drivers/hid/wacom_sys.c b/drivers/hid/wacom_sys.c
>> index 93f49b766376..47d9590b10bd 100644
>> --- a/drivers/hid/wacom_sys.c
>> +++ b/drivers/hid/wacom_sys.c
>> @@ -10,6 +10,7 @@
>>
>> #include "wacom_wac.h"
>> #include "wacom.h"
>> +#include <linux/of.h>
>> #include <linux/input/mt.h>
>>
>> #define WAC_MSG_RETRIES 5
>> @@ -2730,6 +2731,28 @@ static void wacom_mode_change_work(struct work_struct *work)
>> return;
>> }
>>
>> +static void wacom_of_read(struct hid_device *hdev, struct wacom_wac *wacom_wac)
>> +{
>> + if (IS_ENABLED(CONFIG_OF)) {
>> + wacom_wac->flip_tilt_x = of_property_read_bool(hdev->dev.parent->of_node,
>> + "flip-tilt-x");
>> + wacom_wac->flip_tilt_y = of_property_read_bool(hdev->dev.parent->of_node,
>> + "flip-tilt-y");
>> + wacom_wac->flip_pos_x = of_property_read_bool(hdev->dev.parent->of_node,
>> + "flip-pos-x");
>> + wacom_wac->flip_pos_y = of_property_read_bool(hdev->dev.parent->of_node,
>> + "flip-pos-y");
>> + wacom_wac->flip_distance = of_property_read_bool(hdev->dev.parent->of_node,
>> + "flip-distance");
>> + } else {
>> + wacom_wac->flip_tilt_x = false;
>> + wacom_wac->flip_tilt_y = false;
>> + wacom_wac->flip_pos_x = false;
>> + wacom_wac->flip_pos_y = false;
>> + wacom_wac->flip_distance = false;
>> + }
>> +}
>> +
>> static int wacom_probe(struct hid_device *hdev,
>> const struct hid_device_id *id)
>> {
>> @@ -2797,6 +2820,8 @@ static int wacom_probe(struct hid_device *hdev,
>> error);
>> }
>>
>> + wacom_of_read(hdev, wacom_wac);
>> +
>> wacom_wac->probe_complete = true;
>> return 0;
>> }
>> diff --git a/drivers/hid/wacom_wac.c b/drivers/hid/wacom_wac.c
>> index 33a6908995b1..c01f683e23fa 100644
>> --- a/drivers/hid/wacom_wac.c
>> +++ b/drivers/hid/wacom_wac.c
>> @@ -3261,6 +3261,63 @@ static int wacom_status_irq(struct wacom_wac *wacom_wac, size_t len)
>> return 0;
>> }
>>
>> +static int wacom_of_irq(struct wacom_wac *wacom_wac, size_t len)
>> +{
>> + const struct wacom_features *features = &wacom_wac->features;
>> + unsigned char *data = wacom_wac->data;
>> + struct input_dev *input = wacom_wac->pen_input;
>> + unsigned int x, y, pressure;
>> + unsigned char tsw, f1, f2, ers;
>> + short tilt_x, tilt_y, distance;
>> +
>> + if (!IS_ENABLED(CONFIG_OF))
>> + return 0;
>> +
>> + tsw = data[1] & WACOM_TIP_SWITCH_bm;
>> + ers = data[1] & WACOM_ERASER_bm;
>> + f1 = data[1] & WACOM_BARREL_SWITCH_bm;
>> + f2 = data[1] & WACOM_BARREL_SWITCH_2_bm;
>> + x = le16_to_cpup((__le16 *)&data[2]);
>> + y = le16_to_cpup((__le16 *)&data[4]);
>> + pressure = le16_to_cpup((__le16 *)&data[6]);
>> +
>> + /* Signed */
>> + tilt_x = get_unaligned_le16(&data[9]);
>> + tilt_y = get_unaligned_le16(&data[11]);
>> +
>> + distance = get_unaligned_le16(&data[13]);
>> +
>> + /* keep touch state for pen events */
>> + if (!wacom_wac->shared->touch_down)
>> + wacom_wac->tool[0] = (data[1] & 0x0c) ?
>> + BTN_TOOL_RUBBER : BTN_TOOL_PEN;
>> +
>> + wacom_wac->shared->touch_down = data[1] & 0x20;
>> +
>> + // Flip the values based on properties from the device tree
>> +
>> + // Default to a negative value for distance as HID compliant Wacom
>> + // devices generally specify the hovering distance as negative.
>> + distance = wacom_wac->flip_distance ? distance : -distance;
>> + x = wacom_wac->flip_pos_x ? (features->x_max - x) : x;
>> + y = wacom_wac->flip_pos_y ? (features->y_max - y) : y;
>> + tilt_x = wacom_wac->flip_tilt_x ? -tilt_x : tilt_x;
>> + tilt_y = wacom_wac->flip_tilt_y ? -tilt_y : tilt_y;
>> +
>> + input_report_key(input, BTN_TOUCH, tsw || ers);
>> + input_report_key(input, wacom_wac->tool[0], wacom_wac->shared->touch_down);
>> + input_report_key(input, BTN_STYLUS, f1);
>> + input_report_key(input, BTN_STYLUS2, f2);
>> + input_report_abs(input, ABS_X, x);
>> + input_report_abs(input, ABS_Y, y);
>> + input_report_abs(input, ABS_PRESSURE, pressure);
>> + input_report_abs(input, ABS_DISTANCE, distance);
>> + input_report_abs(input, ABS_TILT_X, tilt_x);
>> + input_report_abs(input, ABS_TILT_Y, tilt_y);
>> +
>> + return 1;
>> +}
>> +
>> void wacom_wac_irq(struct wacom_wac *wacom_wac, size_t len)
>> {
>> bool sync;
>> @@ -3379,6 +3436,10 @@ void wacom_wac_irq(struct wacom_wac *wacom_wac, size_t len)
>> sync = wacom_remote_irq(wacom_wac, len);
>> break;
>>
>> + case HID_GENERIC:
>> + sync = wacom_of_irq(wacom_wac, len);
>> + break;
>> +
>> default:
>> sync = false;
>> break;
>> diff --git a/drivers/hid/wacom_wac.h b/drivers/hid/wacom_wac.h
>> index 8b2d4e5b2303..4dd5a56bf347 100644
>> --- a/drivers/hid/wacom_wac.h
>> +++ b/drivers/hid/wacom_wac.h
>> @@ -157,6 +157,14 @@
>> #define WACOM_HID_WT_Y (WACOM_HID_UP_WACOMTOUCH | 0x131)
>> #define WACOM_HID_WT_REPORT_VALID (WACOM_HID_UP_WACOMTOUCH | 0x1d0)
>>
>> +// Bitmasks (for data[3])
>> +#define WACOM_TIP_SWITCH_bm (1 << 0)
>> +#define WACOM_BARREL_SWITCH_bm (1 << 1)
>> +#define WACOM_ERASER_bm (1 << 2)
>> +#define WACOM_INVERT_bm (1 << 3)
>> +#define WACOM_BARREL_SWITCH_2_bm (1 << 4)
>> +#define WACOM_IN_RANGE_bm (1 << 5)
>> +
>> #define WACOM_BATTERY_USAGE(f) (((f)->hid == HID_DG_BATTERYSTRENGTH) || \
>> ((f)->hid == WACOM_HID_WD_BATTERY_CHARGING) || \
>> ((f)->hid == WACOM_HID_WD_BATTERY_LEVEL))
>> @@ -357,6 +365,11 @@ struct wacom_wac {
>> bool has_mode_change;
>> bool is_direct_mode;
>> bool is_invalid_bt_frame;
>> + bool flip_tilt_x;
>> + bool flip_tilt_y;
>> + bool flip_pos_x;
>> + bool flip_pos_y;
>> + bool flip_distance;
>> };
>>
>> #endif
>> --
>> 2.31.1
>>

\
 
 \ /
  Last update: 2021-10-18 23:56    [W:0.289 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site