lkml.org 
[lkml]   [2021]   [Oct]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v1 12/16] pinctrl: starfive: Add pinctrl driver for StarFive SoCs
On Mon, 18 Oct 2021 at 17:48, Andy Shevchenko <andy.shevchenko@gmail.com> wrote:
> On Mon, Oct 18, 2021 at 6:35 PM Emil Renner Berthing <kernel@esmil.dk> wrote:
> > On Tue, 12 Oct 2021 at 19:03, Andy Shevchenko <andy.shevchenko@gmail.com> wrote:
> > > On Tue, Oct 12, 2021 at 4:43 PM Emil Renner Berthing <kernel@esmil.dk> wrote:
>
> When answering, cut down your message to the point, please! It's a bit
> annoying to remove overquoting...
>
> ...
>
> > > > + case PIN_CONFIG_BIAS_DISABLE:
> > >
> > > > + mask |= PAD_BIAS_MASK;
> > >
> > > Use it...
> > >
> > > > + value = (value & ~PAD_BIAS_MASK) | PAD_BIAS_DISABLE;
> > >
> > > ...here. Ditto for the similar cases in this function and elsewhere.
> >
> > I don't follow. How do you want me to use mask? If I did value =
> > (value & ~mask) | PAD_BIAS_DISABLE; then I'd wipe the previous
> > configuration. Eg. suppose the first config is the drive strength and
> > second disables bias. Then on the 2nd loop mask =
> > PAD_DRIVE_STRENGTH_MASK | PAD_BIAS_MASK and the drive strength value
> > would be wiped.
>
> Collect masks and new values in temporary variables and apply them
> once after the loop is done, no?

But that's exactly what the code does. It merges all the config
options into a single mask and value so we only need to do rmw on the
register once.

> ...
>
> > > > + ret = clk_prepare_enable(clk);
> > > > + if (ret) {
> > >
> > > > + reset_control_deassert(rst);
> > >
> > > Use devm_add_action_or_reset().
> >
> > I don't see how that is better.
>
> Pity. The rule of thumb is to either try to use devm_*() everywhere in
> the probe, or don't use it at all. Above is the more-or-less standard
> pattern where devn_add_action_or_reset() is being used in the entire
> kernel.
>
> > Then I'd first need to call that and
> > check for errors, but just on the line below enabling the clock the
> > reset line is deasserted anyway, so then the action isn't needed any
> > longer. So that 3 lines of code for devm_add_action_or_reset +
> > lingering unneeded action or code to remove it again vs. just the line
> > above.
>
> Then don't use devm_*() at all. What's the point?

I'm confused. So you wan't an unneeded action to linger because the
probe function temporarily asserts reset for 3 lines of code?

> ...
>
> > > > + sfp->gc.of_node = dev->of_node;
> > >
> > > Isn't GPIO library do this for you?
> >
> > If it does I can't find it.
>
> Heh... `man git grep`
> Hint: `git grep -n 'of_node = .*of_node' -- drivers/gpio/gpiolib*`

That's exactly what I did.

> --
> With Best Regards,
> Andy Shevchenko

\
 
 \ /
  Last update: 2021-10-18 17:57    [W:0.091 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site