lkml.org 
[lkml]   [2021]   [Oct]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 2/2] watchdog: Add Realtek Otto watchdog timer
Date
On 10/13/21 12:46 PM, Sander Vanheule wrote:
> On Wed, 2021-10-13 at 11:48 -0700, Guenter Roeck wrote:
>> On Wed, Oct 13, 2021 at 03:29:00PM +0200, Sander Vanheule wrote:
> [...]
>
>>>
>>> diff --git a/drivers/watchdog/realtek_otto_wdt.c b/drivers/watchdog/realtek_otto_wdt.c
>>> new file mode 100644
>>> index 000000000000..64c9cba6b0b1
>>> --- /dev/null
>>> +++ b/drivers/watchdog/realtek_otto_wdt.c
>>> @@ -0,0 +1,411 @@
>>> +// SPDX-License-Identifier: GPL-2.0-only
>>> +
>>> +/*
>>> + * Realtek Otto MIPS platform watchdog
>>> + *
>>> + * Watchdog timer that will reset the system after timeout, using the selected
>>> + * reset mode.
>>> + *
>>> + * Counter scaling and timeouts:
>>> + * - Base prescale of (2 << 25), providing tick duration T_0: 168ms @ 200MHz
>>> + * - PRESCALE: logarithmic prescaler adding a factor of {1, 2, 4, 8}
>>> + * - Phase 1: Times out after (PHASE1 + 1) × PRESCALE × T_0
>>> + *   Generates an interrupt, WDT cannot be stopped after phase 1
>>> + * - Phase 2: starts after phase 1, times out after (PHASE2 + 1) × PRESCALE × T_0
>>> + *   Resets the system according to RST_MODE
>>
>> Why is there a phase2 interrupt if phase2 resets the chip ?
>>
>
> The SoC's reset controller has an interrupt line for phase2, even though then it then the
> WDT also resets the system. I don't have any documentation about this peripheral; just
> some vendor code and there the phase2 interrupt isn't enabled. I mainly added it here for
> completeness.
>

It seems pointless to mandate an interrupt just for completeness.

> One thing to note is that after CPU or software reset (not SoC reset) the phase2 flag in
> OTTO_WDT_REG_INTR will be set. That's why I always clear it in otto_wdt_probe(), because
> otherwise enabling the interrupt line would trigger otto_wdt_phase2_isr(). On warm
> restarts this bit could be used to determine if there was a WDT timeout, but not if the
> WDT is configured for cold restarts (i.e. full SoC reset).
>
>>
> [...]
>>> +
>>> +       raw_spin_lock_irqsave(&ctrl->lock, flags);
>>> +       v = ioread32(ctrl->base + OTTO_WDT_REG_CTRL);
>>> +       v |= OTTO_WDT_CTRL_ENABLE;
>>> +       iowrite32(v, ctrl->base + OTTO_WDT_REG_CTRL);
>>> +       raw_spin_unlock_irqrestore(&ctrl->lock, flags);
>>
>> Is it really necessary to disable interrupts for those operations ?
>
> The ISR routines only use REG_INTR, which isn't modified anywhere else (outside of probing
> the device). I will replace these with raw_spin_{lock,unlock} throughout.
>

In that case you should not need any locks at all since the watchdog core ensures
that the device is opened only once (and thus only one entity can enable or disable
the watchdog).

> [...]
>>> +/*
>>> + * The timer asserts the PHASE1/PHASE2 IRQs when the number of ticks exceeds
>>> + * the value stored in those fields. This means the timer will run for at least
>>> + * one tick, so small values need to be clamped to correctly reflect the timeout.
>>> + */
>>> +static inline unsigned int div_round_ticks(unsigned int val, unsigned int
>>> tick_duration,
>>> +               unsigned int min_ticks)
>>> +{
>>> +       return max(min_ticks, DIV_ROUND_CLOSEST(val, tick_duration));
>>
>> Are you sure that DIV_ROUND_CLOSEST is appropriate in those calculations
>> (instead of DIV_ROUND_UP or DIV_ROUND_DOWN) ?
>>
> [...]
>
>>> +
>>> +       timeout_ms = total_ticks * tick_ms;
>>> +       ctrl->wdev.timeout = DIV_ROUND_CLOSEST(timeout_ms, 1000);
>>> +
>>
>> That means the actual timeout (and pretimeout) can be slightly larger
>> than the real timeout. Is this really what you want ?
>
> Is it a problem if the WDT times out later than specified by watchdog_device.(pre)timeout?
> I can see that premature timeouts would be an issue, but I don't suppose it's problematic
> if the WDT is pinged (slightly) sooner than actually required?
>

I am not concerned with early pings. However, if the timeout limit is set to a value
lardger than the real timeout (eg the real timeout is 25.6 seconds and the timeout
value is set to 26 seconds), the reset may occur a bit early. Granted, it doesn't
matter much, but most driver authors would ensure that the timeout is set to 25 seconds
(ie rounded down) in that situation.

> The coarsest ticks are 1342 ms, so it is not always possible to provide the requested
> (pre)timeout value, independent of the rounding scheme. Although I think it should be
> possible to replace timeout rounding by DIV_ROUND_UP (of total_ticks_ms), and pretimeout
> rounding by DIV_ROUND_DOWN (of phase2_ticks_ms), and keep stable timeouts when alternating
> between set_timeout/set_pretimeout.
>
>>
>>> +       pretimeout_ms = phase2_ticks * tick_ms;
>>> +       ctrl->wdev.pretimeout = DIV_ROUND_CLOSEST(pretimeout_ms, 1000);
>>> +
>>> +       return 0;
>>> +}
>>> +
>>> +static int otto_wdt_set_timeout(struct watchdog_device *wdev, unsigned int val)
>>> +{
>>> +       struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
>>> +       unsigned long flags;
>>> +       unsigned int ret;
>>> +
>>> +       if (watchdog_timeout_invalid(wdev, val))
>>> +               return -EINVAL;
>>
>> This is not supposed to happen because the calling code already performs
>> range checks.
>
> Right, I will drop the redundant check here and in set_pretimeout.
>
>>
> [...]
>>> +static int otto_wdt_restart(struct watchdog_device *wdev, unsigned long reboot_mode,
>>> +               void *data)
>>> +{
>>> +       struct otto_wdt_ctrl *ctrl = watchdog_get_drvdata(wdev);
>>> +       u32 reset_mode;
>>> +       u32 v;
>>> +
>>> +       devm_free_irq(ctrl->dev, ctrl->irq_phase1, ctrl);
>>> +
>>
>> Why is this needed (instead of, say, disabling the interrupt) ?
>
> Disabling the interrupt should actually be enough. I'll replace the devm_free_irq() with
> disable_irq(). Somehow I didn't find disable_irq(), even though that was what I was
> looking for...
>
> [...]
>>> +
>>> +       /*
>>> +        * Since pretimeout cannot be disabled, min_timeout is twice the
>>> +        * subsystem resolution. max_timeout is 44s at a bus clock of 200MHz.
>>> +        */
>>> +       ctrl->wdev.min_timeout = 2;
>>> +       max_tick_ms = otto_wdt_tick_ms(ctrl, OTTO_WDT_PRESCALE_MAX);
>>> +       ctrl->wdev.max_timeout =
>>> +               DIV_ROUND_CLOSEST(max_tick_ms * OTTO_WDT_TIMEOUT_TICKS_MAX, 1000);
>>
>> Any reason for using max_timeout instead of max_hw_heartbeat_ms ?
>
> I must have missed this when I was looking at watchdog_device. Makes sense to use
> max_hw_heartbeat_ms since that reflects the actual value more accurately.
>
>>
>
> Thanks for the feedback!
>
> Best,
> Sander
>

\
 
 \ /
  Last update: 2021-10-13 23:04    [W:0.065 / U:0.972 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site