lkml.org 
[lkml]   [2021]   [Oct]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 11/14] mtd: spinand: Perform Power-on-Reset on the flash in mtd_suspend()
Date
A soft reset using FFh command doesn't erase the flash's configuration
and doesn't reset the SPI IO mode also. This can result in the flash
being in a different SPI IO mode, e.g. Octal DTR, when resuming from
sleep. This could put the flash in an unrecognized SPI IO mode, making
it unusable.

Perform a Power-on-Reset (PoR), if available in the flash, when
performing mtd_suspend(). This would set the flash to clean
state for reinitialization during resume and would also ensure that it
is in standard SPI IO mode (1S-1S-1S) before the resume begins.

Signed-off-by: Apurva Nandan <a-nandan@ti.com>
---
drivers/mtd/nand/spi/core.c | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)

diff --git a/drivers/mtd/nand/spi/core.c b/drivers/mtd/nand/spi/core.c
index 9b570570ee81..60408531979a 100644
--- a/drivers/mtd/nand/spi/core.c
+++ b/drivers/mtd/nand/spi/core.c
@@ -1316,6 +1316,11 @@ static void spinand_mtd_resume(struct mtd_info *mtd)
int ret;

spinand->reg_proto = SPINAND_SINGLE_STR;
+ /*
+ * PoR Reset (if available by the manufacturer) is performed at the suspend
+ * time. Hence, those flashes remain in power-on-state at this point, in a
+ * standard SPI IO mode. So, now the core unanimously performs a soft reset.
+ */
ret = spinand_reset_op(spinand);
if (ret)
return;
@@ -1327,6 +1332,21 @@ static void spinand_mtd_resume(struct mtd_info *mtd)
spinand_ecc_enable(spinand, false);
}

+static int spinand_mtd_suspend(struct mtd_info *mtd)
+{
+ struct spinand_device *spinand = mtd_to_spinand(mtd);
+ int ret;
+
+ if (!(spinand->flags & SPINAND_HAS_POR_CMD_BIT))
+ return 0;
+
+ ret = spinand_power_on_rst_op(spinand);
+ if (ret)
+ dev_err(&spinand->spimem->spi->dev, "suspend() failed\n");
+
+ return ret;
+}
+
static int spinand_init(struct spinand_device *spinand)
{
struct device *dev = &spinand->spimem->spi->dev;
@@ -1399,6 +1419,7 @@ static int spinand_init(struct spinand_device *spinand)
mtd->_erase = spinand_mtd_erase;
mtd->_max_bad_blocks = nanddev_mtd_max_bad_blocks;
mtd->_resume = spinand_mtd_resume;
+ mtd->_suspend = spinand_mtd_suspend;

if (nand->ecc.engine) {
ret = mtd_ooblayout_count_freebytes(mtd);
--
2.25.1
\
 
 \ /
  Last update: 2021-10-11 23:41    [W:0.094 / U:0.248 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site