lkml.org 
[lkml]   [2021]   [Jan]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    Date
    From
    Subject[PATCH v3 1/2] arm64: dts: sdm845: add oneplus6/6t devices
    Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based
    on the sdm845-mtp DT with the following functionality:

    * Touch
    * Display
    * GPU
    * Wlan and Bluetooth
    * USB peripheral mode
    * Remoteproc

    Signed-off-by: Caleb Connolly <caleb@connolly.tech>
    ---
    Changes since v1
    * Remove unused pinctrl nodes
    * Properly model touchscreen vio supply GPIO
    * Improve comments
    * Remove bq27541 battery as it doesn't work

    Changes since v2
    * Specify clock frequency of touchscreen i2c
    * Remove tri-state-key nodes until a better solution can be found
    * Cleaned up pinctrl nodes
    * Remove unused regulators
    * Improve formatting
    * Address Bjorn's comments
    * Remove unused regulators
    ---
    arch/arm64/boot/dts/qcom/Makefile | 2 +
    .../boot/dts/qcom/sdm845-oneplus-common.dtsi | 621 ++++++++++++++++++
    .../dts/qcom/sdm845-oneplus-enchilada.dts | 19 +
    .../boot/dts/qcom/sdm845-oneplus-fajita.dts | 23 +
    4 files changed, 665 insertions(+)
    create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
    create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts
    create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts

    diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
    index 5113fac80b7a..19f18af3ecff 100644
    --- a/arch/arm64/boot/dts/qcom/Makefile
    +++ b/arch/arm64/boot/dts/qcom/Makefile
    @@ -44,6 +44,8 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb
    dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb
    dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb
    dtb-$(CONFIG_ARCH_QCOM) += sdm845-xiaomi-beryllium.dtb
    +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb
    +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb
    dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
    dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb
    dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
    diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
    new file mode 100644
    index 000000000000..9efa38c9f1c2
    --- /dev/null
    +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
    @@ -0,0 +1,621 @@
    +// SPDX-License-Identifier: GPL-2.0
    +/*
    + * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source
    + *
    + * Copyright (c) 2020, The Linux Foundation. All rights reserved.
    + */
    +
    +/dts-v1/;
    +
    +#include <dt-bindings/gpio/gpio.h>
    +#include <dt-bindings/input/linux-event-codes.h>
    +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
    +
    +#include "sdm845.dtsi"
    +#include "pm8998.dtsi"
    +#include "pmi8998.dtsi"
    +
    +/delete-node/ &rmtfs_mem;
    +
    +/ {
    +
    + aliases {
    + hsuart0 = &uart6;
    + };
    +
    + reserved-memory {
    + /*
    + * The rmtfs memory region in downstream is 'dynamically allocated'
    + * but given the same address every time. Hard code it as this address is
    + * where the modem firmware expects it to be.
    + */
    + rmtfs_mem: memory@f5b01000 {
    + compatible = "qcom,rmtfs-mem";
    + reg = <0 0xf5b01000 0 0x200000>;
    + no-map;
    +
    + qcom,client-id = <1>;
    + qcom,vmid = <15>;
    + };
    +
    + /*
    + * It seems like reserving the old rmtfs_mem region is also needed to prevent
    + * random crashes which are most likely modem related, more testing needed.
    + */
    + removed_region: memory@88f00000 {
    + no-map;
    + reg = <0 0x88f00000 0 0x200000>;
    + };
    +
    + ramoops: ramoops@ac300000 {
    + compatible = "ramoops";
    + reg = <0 0xac300000 0 0x400000>;
    + record-size = <0x40000>;
    + console-size = <0x40000>;
    + ftrace-size = <0x40000>;
    + pmsg-size = <0x200000>;
    + devinfo-size = <0x1000>;
    + ecc-size = <16>;
    + };
    + };
    +
    + vph_pwr: vph-pwr-regulator {
    + compatible = "regulator-fixed";
    + regulator-name = "vph_pwr";
    + regulator-min-microvolt = <3700000>;
    + regulator-max-microvolt = <3700000>;
    + };
    +
    + /*
    + * Apparently RPMh does not provide support for PM8998 S4 because it
    + * is always-on; model it as a fixed regulator.
    + */
    + vreg_s4a_1p8: pm8998-smps4 {
    + compatible = "regulator-fixed";
    + regulator-name = "vreg_s4a_1p8";
    +
    + regulator-min-microvolt = <1800000>;
    + regulator-max-microvolt = <1800000>;
    +
    + regulator-always-on;
    + regulator-boot-on;
    +
    + vin-supply = <&vph_pwr>;
    + };
    +
    + /*
    + * The touchscreen regulator seems to be controlled somehow by a gpio.
    + * Model it as a fixed regulator and keep it on. Without schematics we
    + * don't know how this is actually wired up...
    + */
    + ts_1p8_supply: ts-1p8-regulator {
    + compatible = "regulator-fixed";
    + regulator-name = "ts_1p8_supply";
    +
    + regulator-min-microvolt = <1800000>;
    + regulator-max-microvolt = <1800000>;
    +
    + gpio = <&tlmm 88 0>;
    + enable-active-high;
    + regulator-boot-on;
    + };
    +
    + gpio-keys {
    + compatible = "gpio-keys";
    + label = "Volume keys";
    + autorepeat;
    +
    + pinctrl-names = "default";
    + pinctrl-0 = <&volume_down_gpio &volume_up_gpio>;
    +
    + vol-down {
    + label = "Volume down";
    + linux,code = <KEY_VOLUMEDOWN>;
    + gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
    + debounce-interval = <15>;
    + };
    +
    + vol-up {
    + label = "Volume up";
    + linux,code = <KEY_VOLUMEUP>;
    + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
    + debounce-interval = <15>;
    + };
    + };
    +};
    +
    +&apps_rsc {
    + pm8998-rpmh-regulators {
    + compatible = "qcom,pm8998-rpmh-regulators";
    + qcom,pmic-id = "a";
    +
    + vdd-s1-supply = <&vph_pwr>;
    + vdd-s2-supply = <&vph_pwr>;
    + vdd-s3-supply = <&vph_pwr>;
    + vdd-s4-supply = <&vph_pwr>;
    + vdd-s5-supply = <&vph_pwr>;
    + vdd-s6-supply = <&vph_pwr>;
    + vdd-s7-supply = <&vph_pwr>;
    + vdd-s8-supply = <&vph_pwr>;
    + vdd-s9-supply = <&vph_pwr>;
    + vdd-s10-supply = <&vph_pwr>;
    + vdd-s11-supply = <&vph_pwr>;
    + vdd-s12-supply = <&vph_pwr>;
    + vdd-s13-supply = <&vph_pwr>;
    + vdd-l1-l27-supply = <&vreg_s7a_1p025>;
    + vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
    + vdd-l3-l11-supply = <&vreg_s7a_1p025>;
    + vdd-l4-l5-supply = <&vreg_s7a_1p025>;
    + vdd-l6-supply = <&vph_pwr>;
    + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
    + vdd-l9-supply = <&vreg_bob>;
    + vdd-l10-l23-l25-supply = <&vreg_bob>;
    + vdd-l13-l19-l21-supply = <&vreg_bob>;
    + vdd-l16-l28-supply = <&vreg_bob>;
    + vdd-l18-l22-supply = <&vreg_bob>;
    + vdd-l20-l24-supply = <&vreg_bob>;
    + vdd-l26-supply = <&vreg_s3a_1p35>;
    + vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
    +
    + vreg_s3a_1p35: smps3 {
    + regulator-min-microvolt = <1352000>;
    + regulator-max-microvolt = <1352000>;
    + };
    +
    + vreg_s5a_2p04: smps5 {
    + regulator-min-microvolt = <1904000>;
    + regulator-max-microvolt = <2040000>;
    + };
    +
    + vreg_s7a_1p025: smps7 {
    + regulator-min-microvolt = <900000>;
    + regulator-max-microvolt = <1028000>;
    + };
    +
    + vdda_mipi_dsi0_pll:
    + vdda_qlink_lv:
    + vdda_ufs1_core:
    + vdda_usb1_ss_core:
    + vreg_l1a_0p875: ldo1 {
    + regulator-min-microvolt = <880000>;
    + regulator-max-microvolt = <880000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + };
    +
    + vreg_l2a_1p2: ldo2 {
    + regulator-min-microvolt = <1200000>;
    + regulator-max-microvolt = <1200000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + regulator-always-on;
    + };
    +
    + vreg_l5a_0p8: ldo5 {
    + regulator-min-microvolt = <800000>;
    + regulator-max-microvolt = <800000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + };
    +
    + vreg_l7a_1p8: ldo7 {
    + regulator-min-microvolt = <1800000>;
    + regulator-max-microvolt = <1800000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + };
    +
    + vdda_qusb_hs0_1p8:
    + vreg_l12a_1p8: ldo12 {
    + regulator-min-microvolt = <1800000>;
    + regulator-max-microvolt = <1800000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + };
    +
    + vreg_l14a_1p88: ldo14 {
    + regulator-min-microvolt = <1800000>;
    + regulator-max-microvolt = <1800000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + regulator-always-on;
    + };
    +
    + vreg_l17a_1p3: ldo17 {
    + regulator-min-microvolt = <1304000>;
    + regulator-max-microvolt = <1304000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + };
    +
    + vreg_l20a_2p95: ldo20 {
    + regulator-min-microvolt = <2704000>;
    + regulator-max-microvolt = <2960000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + };
    +
    + vdda_qusb_hs0_3p1:
    + vreg_l24a_3p075: ldo24 {
    + regulator-min-microvolt = <3088000>;
    + regulator-max-microvolt = <3088000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + };
    +
    + vreg_l25a_3p3: ldo25 {
    + regulator-min-microvolt = <3300000>;
    + regulator-max-microvolt = <3312000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + };
    + vdda_mipi_dsi0_1p2:
    + vdda_ufs1_1p2:
    + vreg_l26a_1p2: ldo26 {
    + regulator-min-microvolt = <1200000>;
    + regulator-max-microvolt = <1200000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + };
    +
    + vreg_l28a_3p0: ldo28 {
    + regulator-min-microvolt = <2856000>;
    + regulator-max-microvolt = <3008000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
    + };
    + };
    +
    + pmi8998-rpmh-regulators {
    + compatible = "qcom,pmi8998-rpmh-regulators";
    + qcom,pmic-id = "b";
    +
    + vdd-bob-supply = <&vph_pwr>;
    +
    + vreg_bob: bob {
    + regulator-min-microvolt = <3312000>;
    + regulator-max-microvolt = <3600000>;
    + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
    + regulator-allow-bypass;
    + };
    + };
    +
    + pm8005-rpmh-regulators {
    + compatible = "qcom,pm8005-rpmh-regulators";
    + qcom,pmic-id = "c";
    +
    + vdd-s1-supply = <&vph_pwr>;
    + vdd-s2-supply = <&vph_pwr>;
    + vdd-s3-supply = <&vph_pwr>;
    + vdd-s4-supply = <&vph_pwr>;
    +
    + vreg_s3c_0p6: smps3 {
    + regulator-min-microvolt = <600000>;
    + regulator-max-microvolt = <600000>;
    + };
    + };
    +};
    +
    +&adsp_pas {
    + status = "okay";
    + firmware-name = "qcom/sdm845/oneplus6/adsp.mbn";
    +};
    +
    +&cdsp_pas {
    + status = "okay";
    + firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn";
    +};
    +
    +&dsi0 {
    + status = "okay";
    + vdda-supply = <&vdda_mipi_dsi0_1p2>;
    +
    + #address-cells = <1>;
    + #size-cells = <0>;
    +
    + /*
    + * Both devices use different panels but all other properties
    + * are common. Compatible line is declared in device dts.
    + */
    + display_panel: panel@0 {
    + status = "disabled";
    +
    + #address-cells = <1>;
    + #size-cells = <0>;
    + reg = <0>;
    +
    + vddio-supply = <&vreg_l14a_1p88>;
    +
    + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
    +
    + pinctrl-names = "default";
    + pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>;
    +
    + port {
    + panel_in: endpoint {
    + remote-endpoint = <&dsi0_out>;
    + };
    + };
    + };
    +};
    +
    +&dsi0_out {
    + remote-endpoint = <&panel_in>;
    + data-lanes = <0 1 2 3>;
    +};
    +
    +&dsi0_phy {
    + status = "okay";
    + vdds-supply = <&vdda_mipi_dsi0_pll>;
    +};
    +
    +&gcc {
    + protected-clocks = <GCC_QSPI_CORE_CLK>,
    + <GCC_QSPI_CORE_CLK_SRC>,
    + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
    + <GCC_LPASS_Q6_AXI_CLK>,
    + <GCC_LPASS_SWAY_CLK>;
    +};
    +
    +&gpu {
    + zap-shader {
    + memory-region = <&gpu_mem>;
    + firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn";
    + };
    +};
    +
    +&i2c12 {
    + status = "okay";
    + clock-frequency = <400000>;
    +
    + synaptics-rmi4-i2c@20 {
    + compatible = "syna,rmi4-i2c";
    + reg = <0x20>;
    + #address-cells = <1>;
    + #size-cells = <0>;
    + interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
    +
    + pinctrl-names = "default";
    + pinctrl-0 = <&ts_default_pins>;
    +
    + vdd-supply = <&vreg_l28a_3p0>;
    + vio-supply = <&ts_1p8_supply>;
    +
    + syna,reset-delay-ms = <200>;
    + syna,startup-delay-ms = <200>;
    +
    + rmi4-f01@1 {
    + reg = <0x01>;
    + syna,nosleep-mode = <1>;
    + };
    +
    + rmi4-f12@12 {
    + reg = <0x12>;
    + touchscreen-x-mm = <68>;
    + touchscreen-y-mm = <144>;
    + syna,sensor-type = <1>;
    + syna,rezero-wait-ms = <200>;
    + };
    + };
    +};
    +
    +&mdss {
    + status = "okay";
    +};
    +
    +&mdss_mdp {
    + status = "okay";
    +};
    +
    +/* Modem/wifi*/
    +&mss_pil {
    + status = "okay";
    + firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn";
    +};
    +
    +&pm8998_gpio {
    + volume_down_gpio: pm8998_gpio5 {
    + pinconf {
    + pins = "gpio5";
    + function = "normal";
    + input-enable;
    + bias-pull-up;
    + qcom,drive-strength = <0>;
    + };
    + };
    +
    + volume_up_gpio: pm8998_gpio6 {
    + pinconf {
    + pins = "gpio6";
    + function = "normal";
    + input-enable;
    + bias-pull-up;
    + qcom,drive-strength = <0>;
    + };
    + };
    +};
    +
    +&qupv3_id_1 {
    + status = "okay";
    +};
    +
    +&qupv3_id_0 {
    + status = "okay";
    +};
    +
    +&qup_i2c12_default {
    + mux {
    + pins = "gpio49", "gpio50";
    + function = "qup12";
    + drive-strength = <2>;
    + bias-disable;
    + };
    +};
    +
    +&qup_i2c10_default {
    + pinconf {
    + pins = "gpio55", "gpio56";
    + drive-strength = <2>;
    + bias-disable;
    + };
    +};
    +
    +&qup_uart9_default {
    + pinconf-tx {
    + pins = "gpio4";
    + drive-strength = <2>;
    + bias-disable;
    + };
    +
    + pinconf-rx {
    + pins = "gpio5";
    + drive-strength = <2>;
    + bias-pull-up;
    + };
    +};
    +
    +// Prevent garbage data on bluetooth UART lines
    +&qup_uart6_default {
    + pinmux {
    + pins = "gpio45", "gpio46", "gpio47", "gpio48";
    + function = "qup6";
    + };
    +
    + cts {
    + pins = "gpio45";
    + bias-pull-down;
    + };
    +
    + rts-tx {
    + pins = "gpio46", "gpio47";
    + drive-strength = <2>;
    + bias-disable;
    + };
    +
    + rx {
    + pins = "gpio48";
    + bias-pull-up;
    + };
    +};
    +
    +&uart6 {
    + status = "okay";
    +
    + bluetooth {
    + compatible = "qcom,wcn3990-bt";
    +
    + /*
    + * This path is relative to the qca/
    + * subdir under lib/firmware.
    + */
    + firmware-name = "oneplus6/crnv21.bin";
    +
    + vddio-supply = <&vreg_s4a_1p8>;
    + vddxo-supply = <&vreg_l7a_1p8>;
    + vddrf-supply = <&vreg_l17a_1p3>;
    + vddch0-supply = <&vreg_l25a_3p3>;
    + max-speed = <3200000>;
    + };
    +};
    +
    +&ufs_mem_hc {
    + status = "okay";
    +
    + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
    +
    + vcc-supply = <&vreg_l20a_2p95>;
    + vcc-max-microamp = <600000>;
    +};
    +
    +&ufs_mem_phy {
    + status = "okay";
    +
    + vdda-phy-supply = <&vdda_ufs1_core>;
    + vdda-pll-supply = <&vdda_ufs1_1p2>;
    +};
    +
    +&usb_1 {
    + status = "okay";
    +
    + /*
    + * disable USB3 clock requirement as the device only supports
    + * USB2.
    + */
    + qcom,select-utmi-as-pipe-clk;
    +};
    +
    +&usb_1_dwc3 {
    + /*
    + * We don't have the capability to switch modes yet.
    + */
    + dr_mode = "peripheral";
    +
    + /* fastest mode for USB 2 */
    + maximum-speed = "high-speed";
    +
    + /* Remove USB3 phy as it's unused on this device. */
    + phys = <&usb_1_hsphy>;
    + phy-names = "usb2-phy";
    +};
    +
    +&usb_1_hsphy {
    + status = "okay";
    +
    + vdd-supply = <&vdda_usb1_ss_core>;
    + vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
    + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
    +
    + qcom,imp-res-offset-value = <8>;
    + qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
    + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
    + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
    +};
    +
    +&tlmm {
    + gpio-reserved-ranges = <0 4>, <81 4>;
    +
    + tri_state_key_default: tri_state_key_default {
    + mux {
    + pins = "gpio40", "gpio42", "gpio26";
    + function = "gpio";
    + drive-strength = <2>;
    + bias-disable;
    + };
    + };
    +
    + ts_default_pins: ts-int {
    + mux {
    + pins = "gpio99", "gpio125";
    + function = "gpio";
    + drive-strength = <16>;
    + bias-pull-up;
    + };
    + };
    +
    + panel_reset_pins: panel-reset {
    + mux {
    + pins = "gpio6", "gpio25", "gpio26";
    + function = "gpio";
    + drive-strength = <8>;
    + bias-disable = <0>;
    + };
    + };
    +
    + panel_te_pin: panel-te {
    + mux {
    + pins = "gpio10";
    + function = "mdp_vsync";
    + drive-strength = <2>;
    + bias-disable;
    + input-enable;
    + };
    + };
    +
    + panel_esd_pin: panel-esd {
    + mux {
    + pins = "gpio30";
    + function = "gpio";
    + drive-strength = <2>;
    + bias-pull-down;
    + input-enable;
    + };
    + };
    +};
    +
    +&wifi {
    + status = "okay";
    + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
    + vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
    + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
    + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
    +
    + qcom,snoc-host-cap-8bit-quirk;
    +};
    \ No newline at end of file
    diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts
    new file mode 100644
    index 000000000000..72842c887617
    --- /dev/null
    +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts
    @@ -0,0 +1,19 @@
    +// SPDX-License-Identifier: GPL-2.0
    +/*
    + * SDM845 OnePlus 6 (enchilada) device tree.
    + *
    + * Copyright (c) 2020, The Linux Foundation. All rights reserved.
    + */
    +
    +#include "sdm845-oneplus-common.dtsi"
    +
    +/ {
    + model = "OnePlus 6";
    + compatible = "oneplus,enchilada", "qcom,sdm845";
    +};
    +
    +&display_panel {
    + status = "okay";
    +
    + compatible = "samsung,sofef00";
    +};
    diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts
    new file mode 100644
    index 000000000000..969b36dc9e2c
    --- /dev/null
    +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts
    @@ -0,0 +1,23 @@
    +// SPDX-License-Identifier: GPL-2.0
    +/*
    + * SDM845 OnePlus 6T (fajita) device tree.
    + *
    + * Copyright (c) 2020, The Linux Foundation. All rights reserved.
    + */
    +
    +#include "sdm845-oneplus-common.dtsi"
    +
    +/ {
    + model = "OnePlus 6T";
    + compatible = "oneplus,fajita", "qcom,sdm845";
    +};
    +
    +&display_panel {
    + status = "okay";
    +
    + compatible = "samsung,s6e3fc2x01";
    +};
    +
    +&rmi4_f12 {
    + touchscreen-y-mm = <148>;
    +};
    --
    2.29.2

    \
     
     \ /
      Last update: 2021-01-14 19:56    [W:4.176 / U:0.168 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site