lkml.org 
[lkml]   [2021]   [Jan]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v9 2/3] Input: Add Novatek NT36xxx touchscreen driver
Il giorno lun 7 dic 2020 alle ore 07:43 Dmitry Torokhov
<dmitry.torokhov@gmail.com> ha scritto:
>
> Hi AngeloGioacchino,
>
> On Wed, Oct 28, 2020 at 11:13:01PM +0100, kholk11@gmail.com wrote:
> > +/**
> > + * nt36xxx_set_page - Set page number for read/write
> > + * @ts: Main driver structure
> > + *
> > + * Return: Always zero for success, negative number for error
> > + */
> > +static int nt36xxx_set_page(struct nt36xxx_i2c *ts, u32 pageaddr)
> > +{
> > + u32 data = cpu_to_be32(pageaddr) >> 8;
> > + int ret;
> > +
> > + ret = regmap_noinc_write(ts->fw_regmap, NT36XXX_CMD_SET_PAGE,
> > + &data, sizeof(data));
> > + if (ret)
> > + return ret;
> > +
> > + usleep_range(100, 200);
> > + return ret;
> > +}
>
> Regmap is supposed to handle paged access for you as long as you set it
> up for paged access. Why do you need custom page handling here?
>
> Thanks.
>
> --
> Dmitry

Regmap's page handling is using regmap_update_bits, hence calling a
regmap_read for each page switch and this is not always possible on
this MCU: especially, but not only, in the CRC reboot case, calling
a regmap_read before the page-switch will result in invalid data.

Hacking through the invalid data, we would still be able to set the
page at this point, but then in the reset-idle sequence handling the
CRC failure, we are setting page again: keeping in mind that this is
a i2c connected MCU, calling a regmap_read while sending the "special"
reset sequence is not in the likes of this MCU SW design, as it is
expecting a specific, precise command sequence.

If that happens, the MCU won't recognize the CRC reset-idle sequence
and will never recover from the error.

This can surely be solved by setting up a FLAT regcache and resetting
the register cache in (many) strategic places but, in my opinion,
that's going to be seriously messy, as I would have to do that in
basically every place - but the CRC reboot loop function, so we'd have
a register cache for *only* one special case in one function (which is
not even supposed to be ever called during regular functionality,
unless the MCU firmware panics somehow).

There is also another reason why I dislike using the paged access that
comes from the regmap API here: as you see, the event buffer address
is different for some ICs (probably for MCU FW differences) and this
would require me to dynamically set the regmap_range_cfg structure in
the probe function, then casting it to a const and setting it into the
regmap_config before registering regmap (which, by the way, is another
const struct).

Ah, also, as you can see the set_page function is doing:
u32 data = cpu_to_be32(pageaddr) >> 8;
clearly, using the regmap page switching, I would have to change the
pages definitions *and* the nt36xxx_mem_map at least partially (because
"win_page << range->selector_shift"), and all of these definitions,
right now, are representing the same addresses that are referenced into
the MCU firmware, other than being basically 1:1 with what the downstream
driver provides.
Changing them around would not only, in some way, "hide" precious infos
on a series of MCUs that are not publicly documented, but would also make
the eventual porting of new ICs/MCUs that would be compatible with this
driver harder for who knows what's going on and *way harder* for other
"casual" developers.

So, for the aforementioned reasons, all summed together, I chose to not
use the regmap paged access.

Yours,
-- Angelo

\
 
 \ /
  Last update: 2021-01-13 14:06    [W:1.086 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site