lkml.org 
[lkml]   [2020]   [Sep]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 2/2] arm64: dts: ti: k3-j7200-common-proc-board: Add support for eMMC and SD card
Date
Add support for the eMMC and SD card connected on the common
processor board

sdhci0 is connected to an eMMC while sdhci1 is connected to the
micro SD slot.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
---
.../dts/ti/k3-j7200-common-proc-board.dts | 28 +++++++++++++++++++
1 file changed, 28 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 03c8817e8745..794241ba74cb 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -28,6 +28,19 @@
J721E_IOPAD(0xe0, PIN_INPUT_PULLUP, 3) /* (T3) EXT_REFCLK1.I2C1_SDA */
>;
};
+
+ main_mmc1_pins_default: main-mmc1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x104, PIN_INPUT, 0) /* (M20) MMC1_CMD */
+ J721E_IOPAD(0x100, PIN_INPUT, 0) /* (P21) MMC1_CLK */
+ J721E_IOPAD(0xfc, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+ J721E_IOPAD(0xf8, PIN_INPUT, 0) /* (M19) MMC1_DAT0 */
+ J721E_IOPAD(0xf4, PIN_INPUT, 0) /* (N21) MMC1_DAT1 */
+ J721E_IOPAD(0xf0, PIN_INPUT, 0) /* (N20) MMC1_DAT2 */
+ J721E_IOPAD(0xec, PIN_INPUT, 0) /* (N19) MMC1_DAT3 */
+ J721E_IOPAD(0xe4, PIN_INPUT, 8) /* (V1) TIMER_IO0.MMC1_SDCD */
+ >;
+ };
};

&wkup_uart0 {
@@ -112,3 +125,18 @@
#gpio-cells = <2>;
};
};
+
+&main_sdhci0 {
+ /* eMMC */
+ non-removable;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&main_sdhci1 {
+ /* SD card */
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ pinctrl-names = "default";
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
--
2.17.1
\
 
 \ /
  Last update: 2020-09-24 13:27    [W:0.069 / U:0.208 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site