lkml.org 
[lkml]   [2020]   [Sep]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 1/2] arm64: dts: qcom: sc7180: Provide pinconf for SPI to use GPIO for CS
From
Date
Quoting Douglas Anderson (2020-09-18 17:45:27)
> When the chip select line is controlled by the QUP, changing CS is a
> time consuming operation. We have to send a command over to the geni
> and wait for it to Ack us every time we want to change (both making it
> high and low). To send this command we have to make a choice in
> software when we want to control the chip select, we have to either:
> A) Wait for the Ack via interrupt which slows down all SPI transfers
> (and incurrs extra processing associated with interrupts).
> B) Sit in a loop and poll, waiting for the Ack.
>
> Neither A) nor B) is a great option.
>
> We can avoid all of this by realizing that, at least on some boards,
> there is no advantage of considering this line to be a geni line.
> While it's true that geni _can_ control the line, it's also true that
> the line can be a GPIO and there is no downside of viewing it that
> way. Setting a GPIO is a simple MMIO operation.
>
> This patch provides definitions so a board can easily select the GPIO
> mode.
>
> NOTE: apparently, it's possible to run the geni in "GSI" mode. In GSI
> the SPI port is allowed to be controlled by more than one user (like
> firmware and Linux) and also the port can operate sequences of
> operations in one go. In GSI mode it _would_ be invalid to look at
> the chip select as a GPIO because that would prevent other users from
> using it. In theory GSI mode would also avoid some overhead by
> allowing us to sequence the chip select better. However, I'll argue
> GSI is not relevant for all boards (and certainly not any boards
> supported by mainline today). Why?
> - Apparently to run a SPI chip in GSI mode you need to initialize it
> (in the bootloader) with a different firmware and then it will
> always run in GSI mode. Since there is no support for GSI mode in
> the current Linux driver, it must be that existing boards don't have
> firmware that's doing that. Note that the kernel device tree
> describes hardware but also firmware, so it is legitimate to make
> the assumption that we don't have GSI firmware in a given dts file.
> - Some boards with sc7180 have SPI connected to the Chrome OS EC or
> security chip (Cr50). The protocols for talking to cros_ec and cr50
> are extremely complex. Both drivers in Linux fully lock the bus
> across several distinct SPI transfers. While I am not an expert on
> GSI mode it feels highly unlikely to me that we'd ever be able to
> enable GSI mode for these devices.
>
> From a testing perspective, running "flashrom -p ec -r /tmp/foo.bin"
> in a loop after this patch shows almost no reduction in time, but the
> number of interrupts per command goes from 32357 down to 30611 (about
> a 5% reduction).
>
> Signed-off-by: Douglas Anderson <dianders@chromium.org>
> ---

Reviewed-by: Stephen Boyd <swboyd@chromium.org>

>
> Changes in v2:
> - Now just add the pinctrl; let a board use it.
>
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 96 ++++++++++++++++++++++++++++
> 1 file changed, 96 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 6678f1e8e395..0534122b9a3c 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -1595,6 +1595,18 @@ pinmux {
> };
> };
>
> + qup_spi0_cs_gpio: qup-spi0-cs-gpio {
> + pinmux {
> + pins = "gpio34", "gpio35",
> + "gpio36";
> + function = "qup00";
> + };
> + pinmux-cs {

Style nit: Add a newline between nodes?

> + pins = "gpio37";
> + function = "gpio";
> + };
> + };
> +
> qup_spi1_default: qup-spi1-default {
> pinmux {
> pins = "gpio0", "gpio1",

\
 
 \ /
  Last update: 2020-09-21 22:07    [W:0.052 / U:0.336 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site