lkml.org 
[lkml]   [2020]   [Aug]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v7 06/13] pwm: add support for sl28cpld PWM controller
On Fri, Aug 07, 2020 at 09:28:31AM +0200, Michael Walle wrote:
> Hi Uwe, Hi Lee,
>
> Am 2020-08-06 10:40, schrieb Uwe Kleine-König:
> > On Mon, Aug 03, 2020 at 11:35:52AM +0200, Michael Walle wrote:
> > > diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
> > > index 7dbcf6973d33..a0d50d70c3b9 100644
> > > --- a/drivers/pwm/Kconfig
> > > +++ b/drivers/pwm/Kconfig
> > > @@ -428,6 +428,16 @@ config PWM_SIFIVE
> > > To compile this driver as a module, choose M here: the module
> > > will be called pwm-sifive.
> > >
> > > +config PWM_SL28CPLD
> > > + tristate "Kontron sl28cpld PWM support"
> > > + select MFD_SIMPLE_MFD_I2C
> >
> > Is it sensible to present this option to everyone? Maybe
> >
> > depends on SOME_SYMBOL_ONLY_TRUE_ON_SL28CPLD || COMPILE_TEST
>
> Because there is now no real MFD driver anymore, there is also
> no symbol for that. The closest would be ARCH_ARM64 but I don't
> think that is a good idea.
>
> Lee, what do you think about adding a symbol to the MFD, which
> selects MFD_SIMPLE_MFD_I2C but doesn't enable any C modules?
>
> I.e.
> config MFD_SL28CPLD
> tristate "Kontron sl28cpld"
> select MFD_SIMPLE_MFD_I2C
> help
> Say yes here to add support for the Kontron sl28cpld board
> management controller.
>
> Then all the other device driver could depend on the MFD_SL28CPLD
> symbol.
>
> [..]
>
> > > +static void sl28cpld_pwm_get_state(struct pwm_chip *chip,
> > > + struct pwm_device *pwm,
> > > + struct pwm_state *state)
> > > +{
> > > + struct sl28cpld_pwm *priv = dev_get_drvdata(chip->dev);
> > > + unsigned int reg;
> > > + int prescaler;
> > > +
> > > + sl28cpld_pwm_read(priv, SL28CPLD_PWM_CTRL, &reg);
> > > +
> > > + state->enabled = reg & SL28CPLD_PWM_CTRL_ENABLE;
> > > +
> > > + prescaler = FIELD_GET(SL28CPLD_PWM_CTRL_PRESCALER_MASK, reg);
> > > + state->period = SL28CPLD_PWM_PERIOD(prescaler);
> > > +
> > > + sl28cpld_pwm_read(priv, SL28CPLD_PWM_CYCLE, &reg);
> > > + state->duty_cycle = SL28CPLD_PWM_TO_DUTY_CYCLE(reg);
> >
> > Should reg be masked to SL28CPLD_PWM_CYCLE_MAX, or is it guaranteed that
> > the upper bits are zero?
>
> Mh, the hardware guarantees that bit7 is zero. So masking with
> SL28CPLD_PWM_CYCLE_MAX won't buy us much. But what I could think
> could go wrong is this: someone set the prescaler to != 0 and the
> duty cycle to a value greater than the max value for this particular
> prescaler mode. For the above calculations this would result in a
> duty_cycle greater than the period, if I'm not mistaken.
>
> The behavior of the hardware is undefined in that case (at the moment
> it will be always on, I guess). So this isn't a valid setting.
> Nevertheless it might happen. So what about the following:
>
> state->duty_cycle = min(state->duty_cycle, state->period);

If you care about this: This can also happen (at least shortly) in
sl28cpld_pwm_apply() as you write SL28CPLD_PWM_CTRL before
SL28CPLD_PWM_CYCLE there.

I wonder if we want to sanitize the values returned from driver's
.get_state in the core; or scream loud (maybe only if PWM_DEBUG is on).

Something like:

if (state->enabled && state->duty_cycle > state->period) {
if (IS_ENABLED(CONFIG_PWM_DEBUG))
dev_warn(chip->dev, ".get_state() returned invalid setting.\n");

state->duty_cycle = state->period;
}

Do we want to catch state->period = 0, too? Do we interpret this as
disabled?

Best regards
Uwe

--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | https://www.pengutronix.de/ |
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2020-08-07 09:46    [W:0.081 / U:0.508 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site