lkml.org 
[lkml]   [2020]   [Aug]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2] media: rcar-vin: Add support to select data pins for YCbCr422-8bit input
Hi Niklas,

On Mon, Aug 3, 2020 at 8:28 PM Niklas <niklas.soderlund@ragnatech.se> wrote:
>
> Hi Lad,
>
> On 2020-08-03 20:17:54 +0100, Lad, Prabhakar wrote:
> > Hi Niklas,
> >
> > Thank you for the review.
> >
> > On Mon, Aug 3, 2020 at 7:06 PM Niklas <niklas.soderlund@ragnatech.se> wrote:
> > >
> > > Hi Lad,
> > >
> > > Thanks for your work.
> > >
> > > On 2020-08-03 17:02:53 +0100, Lad Prabhakar wrote:
> > > > Select the data pins for YCbCr422-8bit input format depending on
> > > > bus_width and data_shift passed as part of DT.
> > > >
> > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > > > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> > > > ---
> > > > Changes for v2:
> > > > * Dropped DT binding documentation patch
> > > > * Select the data pins depending on bus-width and data-shift
> > >
> > > I like this v2 much better then v1, nice work!
> > >
> > > >
> > > > v1 -
> > > > https://patchwork.kernel.org/project/linux-renesas-soc/list/?series=323799
> > > > ---
> > > > drivers/media/platform/rcar-vin/rcar-core.c | 5 +++++
> > > > drivers/media/platform/rcar-vin/rcar-dma.c | 7 +++++++
> > > > drivers/media/platform/rcar-vin/rcar-vin.h | 5 +++++
> > > > 3 files changed, 17 insertions(+)
> > > >
> > > > diff --git a/drivers/media/platform/rcar-vin/rcar-core.c b/drivers/media/platform/rcar-vin/rcar-core.c
> > > > index 7440c8965d27..55005d86928d 100644
> > > > --- a/drivers/media/platform/rcar-vin/rcar-core.c
> > > > +++ b/drivers/media/platform/rcar-vin/rcar-core.c
> > > > @@ -624,6 +624,11 @@ static int rvin_parallel_parse_v4l2(struct device *dev,
> > > > vin->parallel = rvpe;
> > > > vin->parallel->mbus_type = vep->bus_type;
> > > >
> > > > + /* select VInDATA[15:8] pins for YCbCr422-8bit format */
> > > > + if (vep->bus.parallel.bus_width == BUS_WIDTH_8 &&
> > > > + vep->bus.parallel.data_shift == DATA_SHIFT_8)
> > > > + vin->parallel->ycbcr_8b_g = true;
> > > > +
> > >
> > > I would store the bus_width and bus_shift values in the struct
> > > rvin_parallel_entity and evaluate them in place rater then create a flag
> > > for this specific use-case..
> > >
> > Ok will do that.
> >
> > > Also according to the documentation is the check correct? Do we not wish
> > > to use the new mode when bus_width == 16 and bus_shift == 8. The check
> > > you have here seems to describe a 8 lane bus where 0 lanes are used.
> > >
> > bus-width is the actual data lines used, so bus_width == 16 and
> > bus_shift == 8 would mean use lines 23:8, so just check for bus_width
> > == 8 and bus_shift == 8 should be sufficient.
>
> As you and Geert points out I was wrong, they should indeed both be 8.
>
> >
> > > I think you should also verify that bus_shift is either 0 or 8 as that
> > > is all the driver supports.
> > >
> > Not sure if thats correct.In that case this patch wont make sense, I
> > believed we agreed upon we determine the YDS depending on both
> > bus-width and bus-shift.
>
> I'm sorry I think I lost you :-) The driver is not capable of supporting
> bus_width = 8 and bus_shift = 2 right? Maybe we are talking about
> different things.
>
> What I tried to say (updated with the knowledge of that bus_width should
> indeed be 8 and not 16) was that would it make sens to with bus_width=8
> allow for a bus_shift value other then 0 or 8? What for example would
> the driver do if the value was 2?
>
I think this should be possible but I am not sure how this will work.
For example on iWave G21D-Q7 platform with 16-bit wired bus say we
connect a 8-bit camera as below:

bus-width = 8 and bus-shift = 2
VI1_G0_B -> Not connected
VI1_G1_B -> Not connected
VI1_G2_B_16 -> Connected
VI1_G3_B -> Connected
VI1_G4_B -> Connected
VI1_G5_B -> Connected
VI1_G6_B -> Connected
VI1_G7_B -> Connected
VI1_DATA7_B/VI1_B7_B_16 -> Connected
VI1_DATA6_B/VI1_B6_B_16 -> Connected
VI1_DATA5_B/VI1_B5_B_16 -> Not connected
VI1_DATA4_B/VI1_B4_B_16 -> Not connected
VI1_DATA3_B/VI1_B3_B_16 -> Not connected
VI1_DATA2_B/VI1_B2_B_16 -> Not connected
VI1_DATA1_B/VI1_B1_B_16 -> Not connected
VI1_DATA0_B/VI1_B0_B_16 -> Not connected

So in this case for 8-bit YCbCr422 format should YDS be set I am not
sure. Or is this not a valid case at all ?

Cheers,
Prabhakar

> >
> > On iWave G21D-Q7 for VI2 interface VI2_G* pins are connected to SoC
> > and for VIN3 interface Vi3_DATA* pins are connected. So in this case
> > the capture only works for VIN2 only if YDS bit is set for 8-bit 422,
> > and for VIN3 capture only works if YDS is 0
> >
> > &vin2 {
> > status = "okay";
> > pinctrl-0 = <&vin2_pins>;
> > pinctrl-names = "default";
> >
> > port {
> > #address-cells = <1>;
> > #size-cells = <0>;
> >
> > vin2ep: endpoint {
> > remote-endpoint = <&ov7725_2>;
> > bus-width = <8>;
> > data-shift = <8>;
> > };
> > };
> > };
> >
> > &vin3 {
> > status = "okay";
> > pinctrl-0 = <&vin3_pins>;
> > pinctrl-names = "default";
> >
> > port {
> > #address-cells = <1>;
> > #size-cells = <0>;
> >
> > vin3ep: endpoint {
> > remote-endpoint = <&ov7725_3>;
> > bus-width = <8>;
> > };
> > };
> > };
> >
> >
> > > > switch (vin->parallel->mbus_type) {
> > > > case V4L2_MBUS_PARALLEL:
> > > > vin_dbg(vin, "Found PARALLEL media bus\n");
> > > > diff --git a/drivers/media/platform/rcar-vin/rcar-dma.c b/drivers/media/platform/rcar-vin/rcar-dma.c
> > > > index 1a30cd036371..5db483877d65 100644
> > > > --- a/drivers/media/platform/rcar-vin/rcar-dma.c
> > > > +++ b/drivers/media/platform/rcar-vin/rcar-dma.c
> > > > @@ -127,6 +127,8 @@
> > > > #define VNDMR2_FTEV (1 << 17)
> > > > #define VNDMR2_VLV(n) ((n & 0xf) << 12)
> > > >
> > > > +#define VNDMR2_YDS BIT(22)
> > >
> > > This should be grouped with the other VNDMR2_* macros and not on its
> > > own. Also it should be sorted so it should be inserted between
> > > VNDMR2_CES and VNDMR2_FTEV.
> > >
> > > Also I know BIT() is a nice macro but the rest of the driver uses (1 <<
> > > 22), please do the same for this one.
> > >
> > Sure will take care of it.
> >
> > > > +
> > > > /* Video n CSI2 Interface Mode Register (Gen3) */
> > > > #define VNCSI_IFMD_DES1 (1 << 26)
> > > > #define VNCSI_IFMD_DES0 (1 << 25)
> > > > @@ -698,6 +700,11 @@ static int rvin_setup(struct rvin_dev *vin)
> > > > /* Data Enable Polarity Select */
> > > > if (vin->parallel->mbus_flags & V4L2_MBUS_DATA_ENABLE_LOW)
> > > > dmr2 |= VNDMR2_CES;
> > > > +
> > > > + if (vin->parallel->ycbcr_8b_g && vin->mbus_code == MEDIA_BUS_FMT_UYVY8_2X8)
> > > > + dmr2 |= VNDMR2_YDS;
> > > > + else
> > > > + dmr2 &= ~VNDMR2_YDS;
> > >
> > > dmr2 is already unitized and YDS is cleared, no need to clear it again
> > > if you don't wish to set it. Taking this and the comments above into
> > > account this would become something like (not tested),
> > >
> > Agreed.
> >
> > > switch (vin->mbus_code) {
> > > case MEDIA_BUS_FMT_UYVY8_2X8:
> > > if (vin->parallel->bus_width == 16 && vin->parallel->bus_shift == 8)
> > > dmr2 |= VNDMR2_YDS;
> > > break;
> > > default:
> > > break;
> > > }
> > >
> > > > }
> > > >
> > > > /*
> > > > diff --git a/drivers/media/platform/rcar-vin/rcar-vin.h b/drivers/media/platform/rcar-vin/rcar-vin.h
> > > > index c19d077ce1cb..3126fee9a89b 100644
> > > > --- a/drivers/media/platform/rcar-vin/rcar-vin.h
> > > > +++ b/drivers/media/platform/rcar-vin/rcar-vin.h
> > > > @@ -87,6 +87,9 @@ struct rvin_video_format {
> > > > u8 bpp;
> > > > };
> > > >
> > > > +#define BUS_WIDTH_8 8
> > > > +#define DATA_SHIFT_8 8
> > >
> > > As pointed out by Geert, not so useful, use 8 in the code :-)
> > >
> > Agreed will drop it.
> >
> > Cheers,
> > Prabhakar
>
> --
> Regards,
> Niklas Söderlund

\
 
 \ /
  Last update: 2020-08-04 10:06    [W:0.057 / U:1.436 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site