lkml.org 
[lkml]   [2020]   [Aug]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v1] usb: typec: tcpm: Fix TDA 2.2.1.1 and TDA 2.2.1.2 failures
From
Date
On 8/10/20 6:11 PM, Badhri Jagan Sridharan wrote:
>>From the spec:
> "7.1.5 Response to Hard Resets
> Hard Reset Signaling indicates a communication failure has occurred and
> the Source Shall stop driving VCONN, Shall remove Rp from the VCONN pin
> and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The USB connection
> May reset during a Hard Reset since the VBUS voltage will be less than
> vSafe5V for an extended period of time. After establishing the vSafe0V
> voltage condition on VBUS, the Source Shall wait tSrcRecover before
> re-applying VCONN and restoring VBUS to vSafe5V. A Source Shall conform
> to the VCONN timing as specified in [USB Type-C 1.3]."
>
> Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
> ---
> drivers/usb/typec/tcpm/tcpm.c | 16 +++++++++++++---
> 1 file changed, 13 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
> index 3ef37202ee37..e41c4e5d3c71 100644
> --- a/drivers/usb/typec/tcpm/tcpm.c
> +++ b/drivers/usb/typec/tcpm/tcpm.c
> @@ -3372,13 +3372,19 @@ static void run_state_machine(struct tcpm_port *port)
> tcpm_set_state(port, SNK_HARD_RESET_SINK_OFF, 0);
> break;
> case SRC_HARD_RESET_VBUS_OFF:
> - tcpm_set_vconn(port, true);
> + /*
> + * 7.1.5 Response to Hard Resets
> + * Hard Reset Signaling indicates a communication failure has occurred and the
> + * Source Shall stop driving VCONN, Shall remove Rp from the VCONN pin and Shall
> + * drive VBUS to vSafe0V as shown in Figure 7-9.
> + */
> + tcpm_set_vconn(port, false);
> tcpm_set_vbus(port, false);
> tcpm_set_roles(port, port->self_powered, TYPEC_SOURCE,
> tcpm_data_role_for_source(port));
> - tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);

I am a bit concerned about this. If I understand correctly, it means that
we won't turn VBUS back on unless a SRC_HARD_RESET_VBUS_OFF PD event is received.
Is that correct ? What happens if that event is never received ?

Thanks,
Guenter

> break;
> case SRC_HARD_RESET_VBUS_ON:
> + tcpm_set_vconn(port, true);
> tcpm_set_vbus(port, true);
> port->tcpc->set_pd_rx(port->tcpc, true);
> tcpm_set_attached_state(port, true);
> @@ -3944,7 +3950,11 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
> tcpm_set_state(port, SNK_HARD_RESET_WAIT_VBUS, 0);
> break;
> case SRC_HARD_RESET_VBUS_OFF:
> - tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, 0);
> + /*
> + * After establishing the vSafe0V voltage condition on VBUS, the Source Shall wait
> + * tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V.
> + */
> + tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);
> break;
> case HARD_RESET_SEND:
> break;
>

\
 
 \ /
  Last update: 2020-08-11 03:51    [W:0.053 / U:1.332 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site