lkml.org 
[lkml]   [2020]   [Jul]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH V5 0/3] Internal voltage control for qcom SDHC
On Tue, 23 Jun 2020 at 15:35, Veerabhadrarao Badiganti
<vbadigan@codeaurora.org> wrote:
>
> On qcom SD host controllers voltage switching be done after the HW
> is ready for it. The HW informs its readiness through power irq.
> The voltage switching should happen only then.
>
> So added support to register voltage regulators from the msm driver
> and use them.
>
> This patchset was posted long back but not actively pursued
> https://lore.kernel.org/linux-arm-msm/1539004739-32060-1-git-send-email-vbadigan@codeaurora.org/
> So posting it as fresh patchset.
>
> Changes since V4:
> - Added clear comments on condtion which allows either to
> tunf off/on Vqmmc or to set load.
> - Added mmc_card_removable() to the condtion whcih checks
> if the card is eMMC or other card.
> - Rerturning error for unsupported voltagtes in
> sdhci_msm_start_signal_voltage_switch()
> - Moved setting ios.power_mode to mmc_alloc_host().
>
> Changes since V3:
> - Dropped reading of regulator load values from device tree.
> - Dropped documentaiton chagne.
> - Since only Vqmmc supply of eMMC would be kept On during suspend,
> setting load only for this regulator so that it can go to LPM.
> And since this Load reamins same, load value is hard-coded in the driver.
>
> Changes since V2:
> - Removed redundant log from sdhci_msm_set_vmmc.
> - Added the condition for skiping disabling of vqmmc for eMMC.
> - Updated logic such that, setting load for vqmmc only if
> it is kept ON.
> - Retained ack by Adrian for second patch.
> - Updated dt properties names as per Robs comments.
>
> Changes since V1:
> - Removed setting load for Vmmc regulator while turning it on/off.
> Instead setting the active load once during probe.
> - Simplified handlng of supplies for BUS_ON/OFF cases in shci_msm_handle_pwr_irq().
> - Moved common code out of switch case in sdhci_msm_start_signal_voltage_switch().
> - Updated variable name to sdhci_core_to_disable_vqmmc.
> - Updated pr_err logs to dev_err logs.
> Veerabhadrarao Badiganti (2):
> mmc: core: Set default power mode in mmc_alloc_host
> mmc: sdhci-msm: Use internal voltage control
>
> Vijay Viswanath (1):
> mmc: sdhci: Allow platform controlled voltage switching
>
> drivers/mmc/core/host.c | 1 +
> drivers/mmc/host/sdhci-msm.c | 206 +++++++++++++++++++++++++++++++++++++++++--
> drivers/mmc/host/sdhci.c | 32 ++++---
> drivers/mmc/host/sdhci.h | 1 +
> 4 files changed, 218 insertions(+), 22 deletions(-)
>

V5 applied for next (did some minor amendment to patch 2), thanks!

Kind regards
Uffe

\
 
 \ /
  Last update: 2020-07-06 16:51    [W:0.288 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site