lkml.org 
[lkml]   [2020]   [Jul]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4/4] MIPS: ingenic: Hardcode mem size for qi,lb60 board
Date
Old Device Tree for the qi,lb60 (aka. Ben Nanonote) did not have a
'memory' node. The kernel would then read the memory controller
registers to know how much RAM was available.

Since every other supported board has had a 'memory' node from the
beginning, we can just hardcode a RAM size of 32 MiB when running with
an old Device Tree without the 'memory' node.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
arch/mips/jz4740/setup.c | 37 ++++++++-----------------------------
1 file changed, 8 insertions(+), 29 deletions(-)

diff --git a/arch/mips/jz4740/setup.c b/arch/mips/jz4740/setup.c
index d73c9b722bf3..51d906325ce6 100644
--- a/arch/mips/jz4740/setup.c
+++ b/arch/mips/jz4740/setup.c
@@ -14,6 +14,7 @@
#include <linux/of_clk.h>
#include <linux/of_fdt.h>
#include <linux/pm.h>
+#include <linux/sizes.h>
#include <linux/suspend.h>

#include <asm/bootinfo.h>
@@ -22,31 +23,6 @@
#include <asm/reboot.h>
#include <asm/time.h>

-#define JZ4740_EMC_BASE_ADDR 0x13010000
-
-#define JZ4740_EMC_SDRAM_CTRL 0x80
-
-static void __init jz4740_detect_mem(void)
-{
- void __iomem *jz_emc_base;
- u32 ctrl, bus, bank, rows, cols;
- phys_addr_t size;
-
- jz_emc_base = ioremap(JZ4740_EMC_BASE_ADDR, 0x100);
- ctrl = readl(jz_emc_base + JZ4740_EMC_SDRAM_CTRL);
- bus = 2 - ((ctrl >> 31) & 1);
- bank = 1 + ((ctrl >> 19) & 1);
- cols = 8 + ((ctrl >> 26) & 7);
- rows = 11 + ((ctrl >> 20) & 3);
- printk(KERN_DEBUG
- "SDRAM preconfigured: bus:%u bank:%u rows:%u cols:%u\n",
- bus, bank, rows, cols);
- iounmap(jz_emc_base);
-
- size = 1 << (bus + bank + cols + rows);
- add_memory_region(0, size, BOOT_MEM_RAM);
-}
-
static unsigned long __init get_board_mach_type(const void *fdt)
{
if (!fdt_node_check_compatible(fdt, 0, "ingenic,x2000"))
@@ -68,13 +44,16 @@ static unsigned long __init get_board_mach_type(const void *fdt)
void __init plat_mem_setup(void)
{
void *dtb = (void *)fw_passed_dtb;
- int offset;

__dt_setup_arch(dtb);

- offset = fdt_path_offset(dtb, "/memory");
- if (offset < 0)
- jz4740_detect_mem();
+ /*
+ * Old devicetree files for the qi,lb60 board did not have a /memory
+ * node. Hardcode the memory info here.
+ */
+ if (!fdt_node_check_compatible(dtb, 0, "qi,lb60") &&
+ fdt_path_offset(dtb, "/memory") < 0)
+ early_init_dt_add_memory_arch(0, SZ_32M);

mips_machtype = get_board_mach_type(dtb);
}
--
2.27.0
\
 
 \ /
  Last update: 2020-07-30 18:13    [W:2.083 / U:1.336 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site