lkml.org 
[lkml]   [2020]   [Jul]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH] arm64: dts: sun50i-pinephone: add led flash
Date
Hi Maxime,

On Mittwoch, 29. Juli 2020 14:34:44 CEST Maxime Ripard wrote:
> Hi!
>
> On Sat, Jul 25, 2020 at 01:08:12PM +0200, Luca Weiss wrote:
> > All revisions of the PinePhone have an SGM3140 LED flash. The gpios were
> > swapped on v1.0 of the board but this was fixed in later revisions.
> >
> > Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> > ---
> >
> > .../boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts | 5 +++++
> > .../boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts | 5 +++++
> > .../boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts | 5 +++++
> > .../boot/dts/allwinner/sun50i-a64-pinephone.dtsi | 11 +++++++++++
> > 4 files changed, 26 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts
> > b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts index
> > 0c42272106afa..b579b03d4e026 100644
> > --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts
> > @@ -9,3 +9,8 @@ / {
> >
> > model = "Pine64 PinePhone Developer Batch (1.0)";
> > compatible = "pine64,pinephone-1.0", "allwinner,sun50i-a64";
> >
> > };
> >
> > +
> > +&sgm3140 {
> > + flash-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
> > + enable-gpios = <&pio 2 3 GPIO_ACTIVE_HIGH>; /* PC3 */
> > +};
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
> > b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts index
> > 3e99a87e9ce52..8552587aac248 100644
> > --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
> > @@ -28,3 +28,8 @@ &backlight {
> >
> > num-interpolated-steps = <50>;
> > default-brightness-level = <400>;
> >
> > };
> >
> > +
> > +&sgm3140 {
> > + flash-gpios = <&pio 2 3 GPIO_ACTIVE_HIGH>; /* PC3 */
> > + enable-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
> > +};
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts
> > b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts index
> > a9f5b670c9b82..ec77715ba4a2a 100644
> > --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts
> > @@ -38,3 +38,8 @@ &lis3mdl {
> >
> > interrupt-parent = <&pio>;
> > interrupts = <1 1 IRQ_TYPE_EDGE_RISING>; /* PB1 */
> >
> > };
> >
> > +
> > +&sgm3140 {
> > + flash-gpios = <&pio 2 3 GPIO_ACTIVE_HIGH>; /* PC3 */
> > + enable-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
> > +};
> > diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
> > b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi index
> > 25150aba749dc..e0bc1bcc1c1f3 100644
> > --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
> > +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
> > @@ -60,6 +60,17 @@ vibrator {
> >
> > enable-gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
> > vcc-supply = <&reg_dcdc1>;
> >
> > };
> >
> > +
> > + sgm3140: led-controller {
>
> The nodes should be ordered by node-name here

Will update the patch, forgot about that.

> > + compatible = "sgmicro,sgm3140";
> > + vin-supply = <&reg_dcdc1>;
> > +
> > + sgm3140_flash: led {
>
> What do you need the label for?

The label will be used for connecting the flash to the rear camera (which
hasn't been upstreamed yet) using:

flash-leds = <&sgm3140_flash>;

Hope that clears it up.

>
> Thanks!
> Maxime

Regards
Luca


\
 
 \ /
  Last update: 2020-07-29 18:24    [W:3.357 / U:0.004 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site