lkml.org 
[lkml]   [2020]   [Jul]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    Subject[RFC PATCH v6 00/11] Integrity Policy Enforcement LSM (IPE)
    Date
    Overview:
    ------------------------------------

    IPE is a Linux Security Module which allows for a configurable
    policy to enforce integrity requirements on the whole system. It
    attempts to solve the issue of Code Integrity: that any code being
    executed (or files being read), are identical to the version that
    was built by a trusted source.

    The type of system for which IPE is designed for use is an embedded device
    with a specific purpose (e.g. network firewall device in a data center),
    where all software and configuration is built and provisioned by the owner.

    Specifically, a system which leverages IPE is not intended for general
    purpose computing and does not utilize any software or configuration
    built by a third party. An ideal system to leverage IPE has both mutable
    and immutable components, however, all binary executable code is immutable.

    The scope of IPE is constrained to the OS. It is assumed that platform
    firmware verifies the the kernel and optionally the root filesystem (e.g.
    via U-Boot verified boot). IPE then utilizes LSM hooks to enforce a
    flexible, kernel-resident integrity verification policy.

    IPE differs from other LSMs which provide integrity checking (for instance,
    IMA), as it has no dependency on the filesystem metadata itself. The
    attributes that IPE checks are deterministic properties that exist solely
    in the kernel. Additionally, IPE provides no additional mechanisms of
    verifying these files (e.g. IMA Signatures) - all of the attributes of
    verifying files are existing features within the kernel, such as dm-verity
    or fsverity.

    IPE provides a policy that allows owners of the system to easily specify
    integrity requirements and uses dm-verity signatures to simplify the
    authentication of allowed objects like authorized code and data.

    IPE supports two modes, permissive (similar to SELinux's permissive mode)
    and enforce. Permissive mode performs the same checks, and logs policy
    violations as enforce mode, but will not enforce the policy. This allows
    users to test policies before enforcing them.

    The default mode is enforce, and can be changed via the kernel commandline
    parameter `ipe.enforce=(0|1)`, or the securityfs node
    `/sys/kernel/security/ipe/enforce`. The ability to switch modes can be
    compiled out of the LSM via setting the config
    CONFIG_SECURITY_IPE_PERMISSIVE_SWITCH to N.

    IPE additionally supports success auditing. When enabled, all events
    that pass IPE policy and are not blocked will emit an audit event. This
    is disabled by default, and can be enabled via the kernel commandline
    `ipe.success_audit=(0|1)` or the securityfs node
    `/sys/kernel/security/ipe/success_audit`.

    Policies can be staged at runtime through securityfs and activated through
    sysfs. Please see the Deploying Policies section of this cover letter for
    more information.

    The IPE LSM is compiled under CONFIG_SECURITY_IPE.

    Policy:
    ------------------------------------

    IPE policy is designed to be both forward compatible and backwards
    compatible. There is one required line, at the top of the policy,
    indicating the policy name, and the policy version, for instance:

    policy_name="Ex Policy" policy_version=0.0.0

    The policy version indicates the current version of the policy (NOT the
    policy syntax version). This is used to prevent roll-back of policy to
    potentially insecure previous versions of the policy.

    The next portion of IPE policy, are rules. Rules are formed by key=value
    pairs, known as properties. IPE rules require two properties: "action",
    which determines what IPE does when it encounters a match against the
    policy, and "op", which determines when that rule should be evaluated.
    Thus, a minimal rule is:

    op=EXECUTE action=ALLOW

    This example will allow any execution. Additional properties are used to
    restrict attributes about the files being evaluated. These properties are
    intended to be deterministic attributes that are resident in the kernel.
    Available properties for IPE described in the properties section of this
    cover-letter, the repository available in Appendix A, and the kernel
    documentation page.

    Order does not matter for the rule's properties - they can be listed in
    any order, however it is encouraged to have the "op" property be first,
    and the "action" property be last, for readability.

    Additionally, rules are evaluated top-to-bottom. As a result, any
    revocation rules, or denies should be placed early in the file to ensure
    that these rules are evaluated before a rule with "action=ALLOW" is hit.

    Any unknown syntax in IPE policy will result in a fatal error to parse
    the policy. User mode can interrogate the kernel to understand what
    properties and the associated versions through the securityfs node,
    $securityfs/ipe/property_config, which will return a string of form:

    key1=version1
    key2=version2
    .
    .
    .
    keyN=versionN

    User-mode should correlate these versions with the supported values
    identified in the documentation to determine whether a policy should
    be accepted by the system.

    Additionally, a DEFAULT operation must be set for all understood
    operations within IPE. For policies to remain completely forwards
    compatible, it is recommended that users add a "DEFAULT action=ALLOW"
    and override the defaults on a per-operation basis.

    For more information about the policy syntax, please see Appendix A or
    the kernel documentation page.

    Early Usermode Protection:
    --------------------------

    IPE can be provided with a policy at startup to load and enforce.
    This is intended to be a minimal policy to get the system to a state
    where userland is setup and ready to receive commands, at which
    point a policy can be deployed via securityfs. This "boot policy" can be
    specified via the config, SECURITY_IPE_BOOT_POLICY, which accepts a path
    to a plain-text version of the IPE policy to apply. This policy will be
    compiled into the kernel. If not specified, IPE will be disabled until a
    policy is deployed and activated through the method above.

    Policy Examples:
    ------------------------------------

    Allow all:

    policy_name="Allow All" policy_version=0.0.0
    DEFAULT action=ALLOW

    Allow only initial superblock:

    policy_name="Allow All Initial SB" policy_version=0.0.0
    DEFAULT action=DENY

    op=EXECUTE boot_verified=TRUE action=ALLOW

    Allow any signed dm-verity volume and the initial superblock:

    policy_name="AllowSignedAndInitial" policy_version=0.0.0
    DEFAULT action=DENY

    op=EXECUTE boot_verified=TRUE action=ALLOW
    op=EXECUTE dmverity_signature=TRUE action=ALLOW

    Prohibit execution from a specific dm-verity volume:

    policy_name="AllowSignedAndInitial" policy_version=0.0.0
    DEFAULT action=DENY

    op=EXECUTE dmverity_roothash=401fcec5944823ae12f62726e8184407a5fa9599783f030dec146938 action=DENY
    op=EXECUTE boot_verified=TRUE action=ALLOW
    op=EXECUTE dmverity_signature=TRUE action=ALLOW

    Allow only a specific dm-verity volume:

    policy_name="AllowSignedAndInitial" policy_version=0.0.0
    DEFAULT action=DENY

    op=EXECUTE dmverity_roothash=401fcec5944823ae12f62726e8184407a5fa9599783f030dec146938 action=ALLOW

    Deploying Policies:
    -------------------

    Deploying policies is simple. First sign a plain text policy, with a
    certificate that is present in the SYSTEM_TRUSTED_KEYRING of your test
    machine. Through openssl, the signing can be done via:

    openssl smime -sign -in "$MY_POLICY" -signer "$MY_CERTIFICATE" \
    -inkey "$MY_PRIVATE_KEY" -binary -outform der -noattr -nodetach \
    -out "$MY_POLICY.p7s"

    Then, simply cat the file into the IPE's "new_policy" securityfs node:

    cat "$MY_POLICY.p7s" > /sys/kernel/security/ipe/new_policy

    The policy should now be present under the policies/ subdirectory, under
    its "policy_name" attribute.

    The policy is now present in the kernel and can be marked as active,
    via the sysctl "ipe.active_policy":

    echo -n 1 > "/sys/kernel/security/ipe/$MY_POLICY_NAME/active"

    This will now mark the policy as active and the system will be enforcing
    $MY_POLICY_NAME. At any point the policy can be updated on the provision
    that the policy version to be deployed is greater than or equal to the
    running version (to prevent roll-back attacks). This update can be done
    by redirecting the file into the policy's "raw" node, under the policies
    subdirectory:

    cat "$MY_UPDATED_POLICY.p7s" > \
    "/sys/kernel/security/ipe/policies/$MY_POLICY_NAME/raw"

    Additionally, policies can be deleted via the "del_policy" securityfs
    node. Simply write the name of the policy to be deleted to that node:

    echo -n 1 >
    "/sys/kernel/security/ipe/policies/$MY_POLICY_NAME/delete"

    There are two requirements to delete policies:

    1. The policy being deleted must not be the active policy.
    2. The policy being deleted must not be the boot policy.

    It's important to know above that the "echo" command will add a newline
    to the end of the input, and this will be considered as part of the
    filename. You can remove the newline via the -n parameter.

    NOTE: If a MAC LSM is enabled, the securityfs commands will require
    CAP_MAC_ADMIN. This is due to sysfs supporting fine-grained MAC
    attributes, while securityfs at the current moment does not.

    Properties:
    ------------------------------------

    This initial patchset introducing IPE adds three properties:
    'boot_verified', 'dmverity_signature' and 'dmverity_roothash'.

    boot_verified (CONFIG_IPE_BOOT_PROP):
    This property can be utilized for authorization of the first
    super-block that is mounted on the system, where IPE attempts
    to evaluate a file. Typically this is used for systems with
    an initramfs or other initial disk, where this is unmounted before
    the system becomes available, and is not covered by any other property.
    The format of this property is:

    boot_verified=(TRUE|FALSE)

    WARNING: This property will trust any disk where the first IPE
    evaluation occurs. If you do not have a startup disk that is
    unpacked and unmounted (like initramfs), then it will automatically
    trust the root filesystem and potentially overauthorize the entire
    disk.

    dmverity_roothash (CONFIG_IPE_DM_VERITY_ROOTHASH):
    This property can be utilized for authorization or revocation of
    specific dmverity volumes, identified via root hash. It has a
    dependency on the DM_VERITY module. The format of this property is:

    dmverity_roothash=<HashHexDigest>

    dmverity_signature (CONFIG_IPE_DM_VERITY_SIGNATURE):
    This property can be utilized for authorization of all dm-verity
    volumes that have a signed roothash that chains to the system
    trusted keyring. It has a dependency on the
    DM_VERITY_VERIFY_ROOTHASH_SIG config. The format of this property is:

    dmverity_signature=(TRUE|FALSE)

    Testing:
    ------------------------------------

    A test suite is available (Appendix B) for ease of use. For manual
    instructions:

    Enable IPE through the following Kconfigs:

    CONFIG_SECURITY_IPE=y
    CONFIG_SECURITY_IPE_BOOT_POLICY="../AllowAllInitialSB.pol"
    CONFIG_SECURITY_IPE_PERMISSIVE_SWITCH=y
    CONFIG_IPE_BOOT_PROP=y
    CONFIG_IPE_DM_VERITY_ROOTHASH=y
    CONFIG_IPE_DM_VERITY_SIGNATURE=y
    CONFIG_DM_VERITY=y
    CONFIG_DM_VERITY_VERIFY_ROOTHASH_SIG=y
    CONFIG_SYSTEM_TRUSTED_KEYRING=y
    CONFIG_SYSTEM_TRUSTED_KEYS="/path/to/my/cert/list.pem"

    Start a test system, that boots directly from the filesystem, without
    an initrd. I recommend testing in permissive mode until all tests
    pass, then switch to enforce to ensure behavior remains identical.

    boot_verified:

    If booted correctly, the filesystem mounted on / should be marked as
    boot_verified. Verify by turning on success auditing (sysctl
    ipe.success_audit=1), and run a binary. In the audit output,
    `prop_boot_verified` should be `TRUE`.

    To test denials, mount a temporary filesystem (mount -t tmpfs -o
    size=4M tmp tmp), and copy a binary (e.g. ls) to this new
    filesystem. Disable success auditing and attempt to run the file.
    The file should have an audit event, but be allowed to execute in
    permissive mode, and prop_boot_verified should be FALSE.

    dmverity_roothash:

    First, you must create a dm-verity volume. This can be done through
    squashfs-tools and veritysetup (provided by cryptsetup).

    Creating a squashfs volume:

    mksquashfs /path/to/directory/with/executable /path/to/output.squashfs

    Format the volume for use with dm-verity & save the root hash:

    output_rh=$(veritysetup format output.squashfs output.hashtree | \
    tee verity_out.txt | awk "/Root hash/" | \
    sed -E "s/Root hash:\s+//g")

    echo -n $output_rh > output.roothash

    Create a two policies, filling in the appropriate fields below:

    Policy 1:

    policy_name="roothash-denial" policy_version=0.0.0
    DEFAULT action=ALLOW
    op=EXECUTE dmverity_roothash=$output_rh action=DENY

    Policy 2:

    policy_name="roothash-allow" policy_version=0.0.0
    DEFAULT action=ALLOW
    DEFAULT op=EXECUTE action=DENY

    op=EXECUTE boot_verified=TRUE action=ALLOW
    op=EXECUTE dmverity_roothash=$output_rh action=ALLOW

    Deploy each policy, then mark the first, "roothash-denial" as active,
    per the "Deploying Policies" section of this cover letter. Mount the
    dm-verity volume:

    veritysetup open output.squashfs output.hashtree unverified \
    `cat output.roothash`

    mount /dev/mapper/unverified /my/mount/point

    Attempt to execute a binary in the mount point, and it should emit an
    audit event for a match against the rule:

    op=EXECUTE dmverity_roothash=$output_rh action=DENY

    To test the second policy, perform the same steps, but this time, enable
    success auditing before running the executable. The success audit event
    should be a match against this rule:

    op=EXECUTE dmverity_roothash=$output_rh action=ALLOW

    dmverity_signature:

    Follow the setup steps for dmverity_roothash. Sign the roothash via:

    openssl smime -sign -in "output.roothash" -signer "$MY_CERTIFICATE" \
    -inkey "$MY_PRIVATE_KEY" -binary -outform der -noattr \
    -out "output.p7s"

    Create a policy:

    policy_name="verified" policy_version=0.0.0
    DEFAULT action=DENY

    op=EXECUTE boot_verified=TRUE action=ALLOW
    op=EXECUTE dmverity_verified=TRUE action=ALLOW

    Deploy the policy, and mark as active, per the "Deploying Policies"
    section of this cover letter. Mount the dm-verity volume with
    verification:

    veritysetup open output.squashfs output.hashtree unverified \
    `cat output.roothash` --root-hash-signature=output.p7s

    mount /dev/mapper/unverified /my/mount/point

    NOTE: The --root-hash-signature option was introduced in veritysetup
    2.3.0

    Turn on success auditing and attempt to execute a binary in the mount
    point, and it should emit an audit event for a match against the rule:

    op=EXECUTE dmverity_verified=TRUE action=ALLOW

    To test denials, mount the dm-verity volume the same way as the
    "dmverity_roothash" section, and attempt to execute a binary. Failure
    should occur.

    Documentation:
    ------------------------------------

    Full documentation is available on github in IPE's master repository
    (Appendix A). This is intended to be an exhaustive source of documentation
    around IPE.

    Additionally, there is higher level documentation in the admin-guide.

    Technical diagrams are available here:

    http://microsoft.github.io/ipe/technical/diagrams/

    Known Gaps:
    ------------------------------------

    IPE has two known gaps:

    1. IPE cannot verify the integrity of anonymous executable memory, such as
    the trampolines created by gcc closures and libffi, or JIT'd code.
    Unfortunately, as this is dynamically generated code, there is no way for
    IPE to detect that this code has not been tampered with in transition
    from where it was built, to where it is running. As a result, IPE is
    incapable of tackling this problem for dynamically generated code.
    However, there is a patch series being prepared that addresses this
    problem for libffi and gcc closures by implemeting a safer kernel
    trampoline API.

    2. IPE cannot verify the integrity of interpreted languages' programs when
    these scripts invoked via `<interpreter> <file>`. This is because the way
    interpreters execute these files, the scripts themselves are not
    evaluated as executable code through one of IPE's hooks. Interpreters
    can be enlightened to the usage of IPE by trying to mmap a file into
    executable memory (+X), after opening the file and responding to the
    error code appropriately. This also applies to included files, or high
    value files, such as configuration files of critical system components.
    This specific gap is planned on being addressed within IPE. For more
    information on how we plan to address this gap, please see the Future
    Development section, below.

    Future Development:
    ------------------------------------

    Support for filtering signatures by specific certificates. In this case,
    our "dmverity_signature" (or a separate property) can be set to a
    specific certificate declared in IPE's policy, allowing for more
    controlled use-cases determine by a user's PKI structure.

    Support for integrity verification for general file reads. This addresses
    the script interpreter issue indicated in the "Known Gaps" section, as
    these script files are typically opened with O_RDONLY. We are evaluating
    whether to do this by comparing the original userland filepath passed into
    the open syscall, thereby allowing existing callers to take advantage
    without any code changes; the alternate design is to extend the new
    openat2(2) syscall, with an new flag, tentatively called "O_VERIFY". While
    the second option requires a code change for all the interpreters,
    frameworks and languages that wish to leverage it, it is a wholly cleaner
    implementation in the kernel. For interpreters specifically, the O_MAYEXEC
    patch series published by Mickaël Salaün[1] is a similar implementation
    to the O_VERIFY idea described above.

    Onboarding IPE's test suite to KernelCI. Currently we are developing a
    test suite in the same vein as SELinux's test suite. Once development
    of the test suite is complete, and provided IPE is accepted, we intend
    to onboard this test suite onto KernelCI.

    Hardened resistance against roll-back attacks. Currently there exists a
    window of opportunity between user-mode setup and the user-policy being
    deployed, where a prior user-policy can be loaded, that is potentially
    insecure. However, with a kernel update, you can revise the boot policy's
    version to be the same version as the latest policy, closing this window.
    In the future, I would like to close this window of opportunity without
    a kernel update, using some persistent storage mechanism.

    Open Issues:
    ------------

    For linux-audit/integrity folks:
    1. Introduction of new audit definitions in the kernel integrity range - is
    this preferred, as opposed to reusing definitions with existing IMA
    definitions?

    TODOs:
    ------

    linux-audit changes to support the new audit events.


    Appendix:
    ------------------------------------

    A. IPE Github Repository: https://github.com/microsoft/ipe
    Hosted Documentation: https://microsoft.github.io/ipe
    B. IPE Users' Guide: Documentation/admin-guide/LSM/ipe.rst
    C. IPE Test Suite: *TBA* (under development)

    References:
    ------------------------------------

    1. https://lore.kernel.org/linux-integrity/20200505153156.925111-1-mic@digikod.net/

    Changelog:
    ------------------------------------

    v1: Introduced

    v2:
    Split the second patch of the previous series into two.
    Minor corrections in the cover-letter and documentation
    comments regarding CAP_MAC_ADMIN checks in IPE.

    v3:
    Address various comments by Jann Horn. Highlights:
    Switch various audit allocators to GFP_KERNEL.
    Utilize rcu_access_pointer() in various locations.
    Strip out the caching system for properties
    Strip comments from headers
    Move functions around in patches
    Remove kernel command line parameters
    Reconcile the race condition on the delete node for policy by
    expanding the policy critical section.

    Address a few comments by Jonathan Corbet around the documentation
    pages for IPE.

    Fix an issue with the initialization of IPE policy with a "-0"
    version, caused by not initializing the hlist entries before
    freeing.

    v4:
    Address a concern around IPE's behavior with unknown syntax.
    Specifically, make any unknown syntax a fatal error instead of a
    warning, as suggested by Mickaël Salaün.
    Introduce a new securityfs node, $securityfs/ipe/property_config,
    which provides a listing of what properties are enabled by the
    kernel and their versions. This allows usermode to predict what
    policies should be allowed.
    Strip some comments from c files that I missed.
    Clarify some documentation comments around 'boot_verified'.
    While this currently does not functionally change the property
    itself, the distinction is important when IPE can enforce verified
    reads. Additionally, 'KERNEL_READ' was omitted from the documentation.
    This has been corrected.
    Change SecurityFS and SHA1 to a reverse dependency.
    Update the cover-letter with the updated behavior of unknown syntax.
    Remove all sysctls, making an equivalent function in securityfs.
    Rework the active/delete mechanism to be a node under the policy in
    $securityfs/ipe/policies.
    The kernel command line parameters ipe.enforce and ipe.success_audit
    have returned as this functionality is no longer exposed through
    sysfs.

    v5:
    Correct some grammatical errors reported by Randy Dunlap.
    Fix some warnings reported by kernel test bot.
    Change convention around security_bdev_setsecurity. -ENOSYS
    is now expected if an LSM does not implement a particular @name,
    as suggested by Casey Schaufler.
    Minor string corrections related to the move from sysfs to securityfs
    Correct a spelling of an #ifdef for the permissive argument.
    Add the kernel parameters re-added to the documentation.
    Fix a minor bug where the mode being audited on permissive switch
    was the original mode, not the mode being swapped to.
    Cleanup doc comments, fix some whitespace alignment issues.

    v6:
    Change if statement condition in security_bdev_setsecurity to be
    more concise, as suggested by Casey Schaufler and Al Viro
    Drop the 6th patch in the series, "dm-verity move signature check..."
    due to numerous issues, and it ultimately providing no real value.
    Fix the patch tree - the previous iteration appears to have been in a
    torn state (patches 8+9 were merged). This has since been corrected.

    Deven Bowers (11):
    scripts: add ipe tooling to generate boot policy
    security: add ipe lsm evaluation loop and audit system
    security: add ipe lsm policy parser and policy loading
    ipe: add property for trust of boot volume
    fs: add security blob and hooks for block_device
    dm-verity: add bdev_setsecurity hook for dm-verity signature
    ipe: add property for signed dmverity volumes
    dm-verity: add bdev_setsecurity hook for root-hash
    ipe: add property for dmverity roothash
    documentation: add ipe documentation
    cleanup: uapi/linux/audit.h

    Documentation/admin-guide/LSM/index.rst | 1 +
    Documentation/admin-guide/LSM/ipe.rst | 508 +++++++
    .../admin-guide/kernel-parameters.txt | 12 +
    MAINTAINERS | 8 +
    drivers/md/dm-verity-target.c | 10 +-
    drivers/md/dm-verity-verify-sig.c | 14 +-
    drivers/md/dm-verity-verify-sig.h | 10 +-
    fs/block_dev.c | 8 +
    include/linux/device-mapper.h | 3 +
    include/linux/fs.h | 1 +
    include/linux/lsm_hook_defs.h | 5 +
    include/linux/lsm_hooks.h | 12 +
    include/linux/security.h | 22 +
    include/uapi/linux/audit.h | 36 +-
    scripts/Makefile | 1 +
    scripts/ipe/Makefile | 2 +
    scripts/ipe/polgen/.gitignore | 1 +
    scripts/ipe/polgen/Makefile | 7 +
    scripts/ipe/polgen/polgen.c | 136 ++
    security/Kconfig | 12 +-
    security/Makefile | 2 +
    security/ipe/.gitignore | 2 +
    security/ipe/Kconfig | 48 +
    security/ipe/Makefile | 33 +
    security/ipe/ipe-audit.c | 303 ++++
    security/ipe/ipe-audit.h | 24 +
    security/ipe/ipe-blobs.c | 95 ++
    security/ipe/ipe-blobs.h | 18 +
    security/ipe/ipe-engine.c | 213 +++
    security/ipe/ipe-engine.h | 49 +
    security/ipe/ipe-hooks.c | 169 +++
    security/ipe/ipe-hooks.h | 70 +
    security/ipe/ipe-parse.c | 889 +++++++++++
    security/ipe/ipe-parse.h | 17 +
    security/ipe/ipe-pin.c | 93 ++
    security/ipe/ipe-pin.h | 36 +
    security/ipe/ipe-policy.c | 149 ++
    security/ipe/ipe-policy.h | 69 +
    security/ipe/ipe-prop-internal.h | 49 +
    security/ipe/ipe-property.c | 143 ++
    security/ipe/ipe-property.h | 100 ++
    security/ipe/ipe-secfs.c | 1309 +++++++++++++++++
    security/ipe/ipe-secfs.h | 14 +
    security/ipe/ipe.c | 115 ++
    security/ipe/ipe.h | 22 +
    security/ipe/properties/Kconfig | 36 +
    security/ipe/properties/Makefile | 13 +
    security/ipe/properties/boot-verified.c | 82 ++
    security/ipe/properties/dmverity-roothash.c | 153 ++
    security/ipe/properties/dmverity-signature.c | 82 ++
    security/ipe/properties/prop-entry.h | 38 +
    security/ipe/utility.h | 32 +
    security/security.c | 70 +
    53 files changed, 5316 insertions(+), 30 deletions(-)
    create mode 100644 Documentation/admin-guide/LSM/ipe.rst
    create mode 100644 scripts/ipe/Makefile
    create mode 100644 scripts/ipe/polgen/.gitignore
    create mode 100644 scripts/ipe/polgen/Makefile
    create mode 100644 scripts/ipe/polgen/polgen.c
    create mode 100644 security/ipe/.gitignore
    create mode 100644 security/ipe/Kconfig
    create mode 100644 security/ipe/Makefile
    create mode 100644 security/ipe/ipe-audit.c
    create mode 100644 security/ipe/ipe-audit.h
    create mode 100644 security/ipe/ipe-blobs.c
    create mode 100644 security/ipe/ipe-blobs.h
    create mode 100644 security/ipe/ipe-engine.c
    create mode 100644 security/ipe/ipe-engine.h
    create mode 100644 security/ipe/ipe-hooks.c
    create mode 100644 security/ipe/ipe-hooks.h
    create mode 100644 security/ipe/ipe-parse.c
    create mode 100644 security/ipe/ipe-parse.h
    create mode 100644 security/ipe/ipe-pin.c
    create mode 100644 security/ipe/ipe-pin.h
    create mode 100644 security/ipe/ipe-policy.c
    create mode 100644 security/ipe/ipe-policy.h
    create mode 100644 security/ipe/ipe-prop-internal.h
    create mode 100644 security/ipe/ipe-property.c
    create mode 100644 security/ipe/ipe-property.h
    create mode 100644 security/ipe/ipe-secfs.c
    create mode 100644 security/ipe/ipe-secfs.h
    create mode 100644 security/ipe/ipe.c
    create mode 100644 security/ipe/ipe.h
    create mode 100644 security/ipe/properties/Kconfig
    create mode 100644 security/ipe/properties/Makefile
    create mode 100644 security/ipe/properties/boot-verified.c
    create mode 100644 security/ipe/properties/dmverity-roothash.c
    create mode 100644 security/ipe/properties/dmverity-signature.c
    create mode 100644 security/ipe/properties/prop-entry.h
    create mode 100644 security/ipe/utility.h

    --
    2.27.0

    \
     
     \ /
      Last update: 2020-07-30 02:32    [W:3.728 / U:0.084 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site