lkml.org 
[lkml]   [2020]   [Jul]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [RFC PATCH] usb: dwc3: fix maximum_speed check for usb2.0-only core
From
Date
On Fri, 2020-07-24 at 03:32 +0000, Thinh Nguyen wrote:
> Hi,
>
> Thinh Nguyen wrote:
> > Hi,
> >
> > Chunfeng Yun wrote:
> >> The maximum_speed will be USB_SPEED_SUPER_PLUS, but the
> >> maximum_speed check for usb2.0-only core doesn't consider it,
> >> so fix it, and move the ckeck into dwc3_check_params().
> >>
> >> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> >> ---
> >> Note:
> >>
> >> When I look at the code, find that this may be a problem, but no
> >> platform to test it.
> >> ---
> >> drivers/usb/dwc3/core.c | 14 +++++++-------
> >> 1 file changed, 7 insertions(+), 7 deletions(-)
> >>
> >> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> >> index 25c686a7..ffd5ab3 100644
> >> --- a/drivers/usb/dwc3/core.c
> >> +++ b/drivers/usb/dwc3/core.c
> >> @@ -930,13 +930,6 @@ static int dwc3_core_init(struct dwc3 *dwc)
> >> */
> >> dwc3_writel(dwc->regs, DWC3_GUID, LINUX_VERSION_CODE);
> >>
> >> - /* Handle USB2.0-only core configuration */
> >> - if (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) ==
> >> - DWC3_GHWPARAMS3_SSPHY_IFC_DIS) {
> >> - if (dwc->maximum_speed == USB_SPEED_SUPER)
> >> - dwc->maximum_speed = USB_SPEED_HIGH;
> >> - }
> >> -
> >> ret = dwc3_phy_setup(dwc);
> >> if (ret)
> >> goto err0;
> >> @@ -1426,6 +1419,13 @@ static void dwc3_check_params(struct dwc3 *dwc)
> >>
> >> break;
> >> }
> >> +
> >> + /* Handle USB2.0-only core configuration */
> >> + if (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) ==
> >> + DWC3_GHWPARAMS3_SSPHY_IFC_DIS) {
> >> + if (dwc->maximum_speed > USB_SPEED_HIGH)
> >> + dwc->maximum_speed = USB_SPEED_HIGH;
> >> + }
> >> }
> >>
> >> static int dwc3_probe(struct platform_device *pdev)
> > Actually, the dwc->maximum_speed captures the maximum speed device
> > property value. It maybe be set based on the phy's capability if there's
> > no property specifying it (i.e. maximum_speed is USB_SPEED_UNKNOWN).
> >
> > So, this code should be removed. The fix should be in the check of
> > dwc3_check_params(). If maximum_speed = USB_SPEED_UNKNOWN and the phy's
> > capability is only up to highspeed, then set the maximum_speed to
> > highspeed only.
Sorry for the late reply, my outlook lose your email.
> >
>
> Are you going into update and resend this patch?
I don't know how to check "the phy's capability is only up to highspeed"

> If not I can create one
> and add your "Reported-by"
Ok, thanks

>
> BR,
> Thinh

\
 
 \ /
  Last update: 2020-07-24 10:30    [W:0.102 / U:0.264 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site