lkml.org 
[lkml]   [2020]   [Jul]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] arm64: dts: sc7180: Add wakeup support over UART RX
Hi Matthias,

On 2020-04-27 22:26, Matthias Kaehlcke wrote:
> Hi,
>
> On Mon, Apr 27, 2020 at 11:57:24AM +0530, satya priya wrote:
>> Add the necessary pinctrl and interrupts to make UART
>> wakeup capable.
>>
>> Signed-off-by: satya priya <skakit@codeaurora.org>
>> ---
>> arch/arm64/boot/dts/qcom/sc7180.dtsi | 7 +++++--
>> 1 file changed, 5 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi
>> b/arch/arm64/boot/dts/qcom/sc7180.dtsi
>> index 4216b57..3a49603 100644
>> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
>> @@ -637,9 +637,12 @@
>> reg = <0 0x0088c000 0 0x4000>;
>> clock-names = "se";
>> clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
>> - pinctrl-names = "default";
>> + pinctrl-names = "default", "sleep";
>> pinctrl-0 = <&qup_uart3_default>;
>> - interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
>> + pinctrl-1 = <&qup_uart3_default>;
>
> Why is the 'sleep' configuration needed if it's the same as 'default'?

Sleep configuration is needed to make sure correct pinctrl setting is
done for RX.
When we register wakeup interrupt, function select is changed to 0 or
GPIO, and after that when state on is called, down the line it is
checking the current state, if it's same as previous state(default), it
won't do any thing and returns 0. Thus the pinctrl setting for RX
remains with "GPIO" function select causing transfer failures.

int pinctrl_select_state(struct pinctrl *p, struct pinctrl_state *state)
{
if (p->state == state)
return 0;

return pinctrl_commit_state(p, state);
}
EXPORT_SYMBOL_GPL(pinctrl_select_state);

However, in V2 we have added sleep state separately to make wakeup
feature work properly.

>
>> + interrupts-extended =
>> + <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
>> + <&tlmm 41 0>;
>> status = "disabled";
>> };
>
> This patch only adds wakeup support for uart3, which seems an arbitrary
> choice at SoC level. Either it should do it for all UARTs of the
> SC7180,
> or in the .dtsi of devices that use UART3 and need it to be wakeup
> capable.

Ok. Added wakeup support to all the UARTs of SC7180 in V2.

Thanks,
Satya Priya

\
 
 \ /
  Last update: 2020-07-24 05:57    [W:0.547 / U:0.692 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site