lkml.org 
[lkml]   [2020]   [Jul]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH net-next v2 0/7] Add an MDIO sub-node under MACB
Date
On 22.07.2020 13:32, Claudiu Beznea - M18063 wrote:
>
>
> On 21.07.2020 20:13, Codrin Ciubotariu wrote:
>> Adding the PHY nodes directly under the Ethernet node became deprecated,
>> so the aim of this patch series is to make MACB use an MDIO node as
>> container for MDIO devices.
>> This patch series starts with a small patch to use the device-managed
>> devm_mdiobus_alloc(). In the next two patches we update the bindings and
>> adapt macb driver to parse the device-tree PHY nodes from under an MDIO
>> node. The last patches add the MDIO node in the device-trees of sama5d2,
>> sama5d3, samad4 and sam9x60 boards.
>>
>
> Tested this series on sama5d2_xplained in the following scenarios:
>
> 1/ PHY bindings from patch 4/7:
> mdio {
> #address-cells = <1>;
> #size-cells = <0>;
> ethernet-phy@1 {
> reg = <0x1>;
> interrupt-parent = <&pioA>;
> interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;
> };
>
> 2/ PHY bindings before this series:
> ethernet-phy@1 {
> reg = <0x1>;
> interrupt-parent = <&pioA>;
> interrupts = <PIN_PC9 IRQ_TYPE_LEVEL_LOW>;
> };
>
> 3/ No PHY bindings at all.
>
> All 3 cases went OK.
>
> You can add:
> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
> Acked-by: Claudiu Beznea <claudiu.beznea@microchip.com>

Thank you very much Claudiu!
There is still one more case in my mind. macb could be a fixed-link with
an MDIO DSA switch. While the macb would have a fixed connection with a
port from the DSA switch, the switch could be configured using macb's
MDIO. The dt would be something like:

macb {
fixed-link {
...
};
mdio {
switch@0 {
...
};
};
};

To support this, in patch 3/7 I should first check for the mdio node to
return of_mdiobus_register() and then check if it's a fixed-link to
return simple mdiobus_register(). I will address this in v3...

Thanks and best regards,
Codrin

>
> Thank you,
> Claudiu Beznea
>
>> Changes in v2:
>> - renamed patch 2/7 from "macb: bindings doc: use an MDIO node as a
>> container for PHY nodes" to "dt-bindings: net: macb: use an MDIO
>> node as a container for PHY nodes"
>> - added back a newline removed by mistake in patch 3/7
>>
>> Codrin Ciubotariu (7):
>> net: macb: use device-managed devm_mdiobus_alloc()
>> dt-bindings: net: macb: use an MDIO node as a container for PHY nodes
>> net: macb: parse PHY nodes found under an MDIO node
>> ARM: dts: at91: sama5d2: add an mdio sub-node to macb
>> ARM: dts: at91: sama5d3: add an mdio sub-node to macb
>> ARM: dts: at91: sama5d4: add an mdio sub-node to macb
>> ARM: dts: at91: sam9x60: add an mdio sub-node to macb
>>
>> Documentation/devicetree/bindings/net/macb.txt | 15 ++++++++++++---
>> arch/arm/boot/dts/at91-sam9x60ek.dts | 8 ++++++--
>> arch/arm/boot/dts/at91-sama5d27_som1.dtsi | 16 ++++++++++------
>> arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi | 17 ++++++++++-------
>> arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 13 ++++++++-----
>> arch/arm/boot/dts/at91-sama5d2_xplained.dts | 12 ++++++++----
>> arch/arm/boot/dts/at91-sama5d3_xplained.dts | 16 ++++++++++++----
>> arch/arm/boot/dts/at91-sama5d4_xplained.dts | 12 ++++++++----
>> drivers/net/ethernet/cadence/macb_main.c | 18 ++++++++++++------
>> 9 files changed, 86 insertions(+), 41 deletions(-)

\
 
 \ /
  Last update: 2020-07-22 13:40    [W:0.157 / U:0.456 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site