lkml.org 
[lkml]   [2020]   [Jul]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V1 2/2] mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode
Date
Add HW tuning support for SD host controller in SDR104 mode

Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
---
Change in V1:
1. Add HW tuning for SDR104 mode instead of SW tuning
2. Change clock base to 208Mhz in SDR104 mode
3. Add CMD and DATA line reset after HW tuning command
---
drivers/mmc/host/sdhci-pci-o2micro.c | 33 ++++++++++++++++++++++++----
1 file changed, 29 insertions(+), 4 deletions(-)

diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index ed3c605fcf0c..fa76748d8929 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -196,7 +196,7 @@ static void __sdhci_o2_execute_tuning(struct sdhci_host *host, u32 opcode)
{
int i;

- sdhci_send_tuning(host, MMC_SEND_TUNING_BLOCK_HS200);
+ sdhci_send_tuning(host, opcode);

for (i = 0; i < 150; i++) {
u16 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
@@ -305,10 +305,12 @@ static int sdhci_o2_execute_tuning(struct mmc_host *mmc, u32 opcode)
* This handler only implements the eMMC tuning that is specific to
* this controller. Fall back to the standard method for other TIMING.
*/
- if (host->timing != MMC_TIMING_MMC_HS200)
+ if ((host->timing != MMC_TIMING_MMC_HS200) &&
+ (host->timing != MMC_TIMING_UHS_SDR104))
return sdhci_execute_tuning(mmc, opcode);

- if (WARN_ON(opcode != MMC_SEND_TUNING_BLOCK_HS200))
+ if (WARN_ON((opcode != MMC_SEND_TUNING_BLOCK_HS200) &&
+ (opcode != MMC_SEND_TUNING_BLOCK)))
return -EINVAL;
/*
* Judge the tuning reason, whether caused by dll shift
@@ -342,6 +344,9 @@ static int sdhci_o2_execute_tuning(struct mmc_host *mmc, u32 opcode)
sdhci_set_bus_width(host, current_bus_width);
}

+ sdhci_reset(host, SDHCI_RESET_CMD);
+ sdhci_reset(host, SDHCI_RESET_DATA);
+
host->flags &= ~SDHCI_HS400_TUNING;
return 0;
}
@@ -369,7 +374,6 @@ static void o2_pci_led_enable(struct sdhci_pci_chip *chip)
scratch_32 |= O2_SD_LED_ENABLE;
pci_write_config_dword(chip->pdev,
O2_SD_TEST_REG, scratch_32);
-
}

static void sdhci_pci_o2_fujin2_pci_init(struct sdhci_pci_chip *chip)
@@ -497,6 +501,10 @@ static void sdhci_o2_enable_clk(struct sdhci_host *host, u16 clk)
static void sdhci_pci_o2_set_clock(struct sdhci_host *host, unsigned int clock)
{
u16 clk;
+ u8 scratch;
+ u32 scratch_32;
+ struct sdhci_pci_slot *slot = sdhci_priv(host);
+ struct sdhci_pci_chip *chip = slot->chip;

host->mmc->actual_clock = 0;

@@ -505,6 +513,23 @@ static void sdhci_pci_o2_set_clock(struct sdhci_host *host, unsigned int clock)
if (clock == 0)
return;

+ if ((host->timing == MMC_TIMING_UHS_SDR104) && (clock == 200000000)) {
+ pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
+
+ scratch &= 0x7f;
+ pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
+
+ pci_read_config_dword(chip->pdev, O2_SD_PLL_SETTING, &scratch_32);
+
+ if ((scratch_32 & 0xFFFF0000) != 0x2c280000)
+ o2_pci_set_baseclk(chip, 0x2c280000);
+
+ pci_read_config_byte(chip->pdev, O2_SD_LOCK_WP, &scratch);
+
+ scratch |= 0x80;
+ pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
+ }
+
clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
sdhci_o2_enable_clk(host, clk);
}
--
2.25.1
\
 
 \ /
  Last update: 2020-07-21 03:30    [W:1.197 / U:0.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site