lkml.org 
[lkml]   [2020]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v8 6/7] arm64: dts: add dts nodes for MT6779
From
Date
On Tue, 2020-07-14 at 20:14 +0200, Matthias Brugger wrote:
>
> On 14/07/2020 11:20, Hanks Chen wrote:
> > this adds initial MT6779 dts settings for board support,
> > including cpu, gic, timer, ccf, pinctrl, uart, sysirq...etc.
> >
> > Signed-off-by: Hanks Chen <hanks.chen@mediatek.com>
> > ---
> > arch/arm64/boot/dts/mediatek/Makefile | 1 +
> > arch/arm64/boot/dts/mediatek/mt6779-evb.dts | 31 +++
> > arch/arm64/boot/dts/mediatek/mt6779.dtsi | 271 ++++++++++++++++++++
> > 3 files changed, 303 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt6779-evb.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt6779.dtsi
> >
> [...]
> > +
> > + uart0: serial@11002000 {
> > + compatible = "mediatek,mt6779-uart",
> > + "mediatek,mt6577-uart";
> > + reg = <0 0x11002000 0 0x400>;
> > + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
> > + clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART0>;
> > + clock-names = "baud", "bus";
> > + status = "disabled";
> > + };
> > +
> > + uart1: serial@11003000 {
> > + compatible = "mediatek,mt6779-uart",
> > + "mediatek,mt6577-uart";
> > + reg = <0 0x11003000 0 0x400>;
> > + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_LOW>;
> > + clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART1>;
> > + clock-names = "baud", "bus";
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial@11004000 {
> > + compatible = "mediatek,mt6779-uart",
> > + "mediatek,mt6577-uart";
> > + reg = <0 0x11004000 0 0x400>;
> > + interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_LOW>;
> > + clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART2>;
> > + clock-names = "baud", "bus";
> > + status = "disabled";
> > + };
>
> Devicetree describes the HW we have. As far as I know, we have 4 UARTs on
> MT6779. So we should list them all here.
>

Actually, We have only 3 UARTs HW on MT6779, but have 4 UART clk in
header file of clk.
CLK_INFRA_UART3 is a dummy clk interface, it has no effect on the
operation of the read/write instruction.

If you think it is not good, I can remove it in the header file of clk.

Thanks

> Regards,
> Matthias

\
 
 \ /
  Last update: 2020-07-16 06:04    [W:0.106 / U:0.572 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site