lkml.org 
[lkml]   [2020]   [Jun]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 02/11] mfd: Add support for Kontron sl28cpld management controller
On Mon, 08 Jun 2020, Michael Walle wrote:

> Am 2020-06-08 20:56, schrieb Lee Jones:
> > On Mon, 08 Jun 2020, Michael Walle wrote:
> >
> > > Am 2020-06-08 12:02, schrieb Andy Shevchenko:
> > > > +Cc: some Intel people WRT our internal discussion about similar
> > > > problem and solutions.
> > > >
> > > > On Mon, Jun 8, 2020 at 11:30 AM Lee Jones <lee.jones@linaro.org> wrote:
> > > > > On Sat, 06 Jun 2020, Michael Walle wrote:
> > > > > > Am 2020-06-06 13:46, schrieb Mark Brown:
> > > > > > > On Fri, Jun 05, 2020 at 10:07:36PM +0200, Michael Walle wrote:
> > > > > > > > Am 2020-06-05 12:50, schrieb Mark Brown:
> > > >
> > > > ...
> > > >
> > > > > Right. I'm suggesting a means to extrapolate complex shared and
> > > > > sometimes intertwined batches of register sets to be consumed by
> > > > > multiple (sub-)devices spanning different subsystems.
> > > > >
> > > > > Actually scrap that. The most common case I see is a single Regmap
> > > > > covering all child-devices.
> > > >
> > > > Yes, because often we need a synchronization across the entire address
> > > > space of the (parent) device in question.
> > > >
> > > > > It would be great if there was a way in
> > > > > which we could make an assumption that the entire register address
> > > > > space for a 'tagged' (MFD) device is to be shared (via Regmap) between
> > > > > each of the devices described by its child-nodes. Probably by picking
> > > > > up on the 'simple-mfd' compatible string in the first instance.
> > > > >
> > > > > Rob, is the above something you would contemplate?
> > > > >
> > > > > Michael, do your register addresses overlap i.e. are they intermingled
> > > > > with one another? Do multiple child devices need access to the same
> > > > > registers i.e. are they shared?
> > >
> > > No they don't overlap, expect for maybe the version register, which is
> > > just there once and not per function block.
> >
> > Then what's stopping you having each device Regmap their own space?
>
> Because its just one I2C device, AFAIK thats not possible, right?

Not sure what (if any) the restrictions are.

I can't think of any reasons why not, off the top of my head.

Does Regmap only deal with shared accesses from multiple devices
accessing a single register map, or can it also handle multiple
devices communicating over a single I2C channel?

One for Mark perhaps.

> > The issues I wish to resolve using 'simple-mfd' are when sub-devices
> > register maps overlap and intertwine.

[...]

> > > > > What do these bits configure?
> > >
> > > - hardware strappings which have to be there before the board powers
> > > up,
> > > like clocking mode for different SerDes settings
> > > - "keep-in-reset" bits for onboard peripherals if you want to save
> > > power
> > > - disable watchdog bits (there is a watchdog which is active right
> > > from
> > > the start and supervises the bootloader start and switches to
> > > failsafe
> > > mode if it wasn't successfully started)
> > > - special boot modes, like eMMC, etc.
> > >
> > > Think of it as a 16bit configuration word.
> >
> > And you wish for users to be able to view these at run-time?
>
> And esp. change them.
>
> > Can they adapt any of them on-the-fly or will the be RO?
>
> They are R/W but only will only affect the board behavior after a reset.

I see. Makes sense. This is board controller territory. Perhaps
suitable for inclusion into drivers/soc or drivers/platform.

--
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog

\
 
 \ /
  Last update: 2020-06-09 08:49    [W:0.405 / U:0.672 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site