lkml.org 
[lkml]   [2020]   [Jun]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] xhci: Make debug message consistent with bus and port number
From
Date
On 8.6.2020 6.57, Kai-Heng Feng wrote:
>
>
>> On May 7, 2020, at 18:35, Mathias Nyman <mathias.nyman@linux.intel.com> wrote:
>>
>> On 7.5.2020 11.21, Greg Kroah-Hartman wrote:
>>> On Thu, May 07, 2020 at 03:58:36PM +0800, Kai-Heng Feng wrote:
>>>>
>>>>
>>>>> On May 7, 2020, at 15:31, Greg Kroah-Hartman <gregkh@linuxfoundation.org> wrote:
>>>>>
>>>>> On Thu, May 07, 2020 at 03:15:01PM +0800, Kai-Heng Feng wrote:
>>>>>>
>>>>>>
>>>>>>> On May 7, 2020, at 14:45, Greg Kroah-Hartman <gregkh@linuxfoundation.org> wrote:
>>>>>>>
>>>>>>> On Thu, May 07, 2020 at 02:17:55PM +0800, Kai-Heng Feng wrote:
>>>>>>>> Current xhci debug message doesn't always output bus number, so it's
>>>>>>>> hard to figure out it's from USB2 or USB3 root hub.
>>>>>>>>
>>>>>>>> In addition to that, some port numbers are offset to 0 and others are
>>>>>>>> offset to 1. Use the latter to match the USB core.
>>>>>>>>
>>>>>>>> So use "bus number - port index + 1" to make debug message consistent.
>>>>>>>>
>>>>>>>> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
>>>>>>>> ---
>>>>>>>> drivers/usb/host/xhci-hub.c | 41 +++++++++++++++++++++----------------
>>>>>>>> 1 file changed, 23 insertions(+), 18 deletions(-)
>>>>>>>>
>>>>>>>> diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
>>>>>>>> index f37316d2c8fa..83088c262cc4 100644
>>>>>>>> --- a/drivers/usb/host/xhci-hub.c
>>>>>>>> +++ b/drivers/usb/host/xhci-hub.c
>>>>>>>> @@ -1241,7 +1241,8 @@ int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue,
>>>>>>>> temp = readl(ports[wIndex]->addr);
>>>>>>>> /* Disable port */
>>>>>>>> if (link_state == USB_SS_PORT_LS_SS_DISABLED) {
>>>>>>>> - xhci_dbg(xhci, "Disable port %d\n", wIndex);
>>>>>>>> + xhci_dbg(xhci, "Disable port %d-%d\n",
>>>>>>>> + hcd->self.busnum, wIndex + 1);
>>>>>>>
>>>>>>> Shouldn't xhci_dbg() show the bus number already?
>>>>>>
>>>>>> It's the PCI bus number, different to USB2/USB3 root hub bus number...
>>>>>
>>>>> But if this is using dev_dbg(), and it is, then you know how to look
>>>>> that up by seeing where that device is in sysfs at that point in time.
>>>>>
>>>>> So why add this again?
>>>>
>>>> xHCI has two HCD, one for USB2 and one for USB3.
>>>> If both of their port with same number are in use, for instance, port 1, then they are port 1-1 and port 2-1.
>>>> Right now the debug message only show "Port 1", we still can't find the corresponding port via sysfs with insufficient info.
>>>
>>> Look at the full kernel log line, the xhci hcd device should be showing
>>> you unique information. If not, something else is wrong.
>>>
>>
>> What Kai-Heng suggest here makes sense, and is useful.
>> We use similar style debugging in other places, and it is helpful as it matches
>> usb core debugging style.
>>
>> This might seem odd but reason is that the xHC controller is one device which
>> doesn't really separate USB2 and USB3.
>> All ports are for example in one long array.
>>
>> On the xhci driver side things look very different. We register two HCD's,
>> one for usb 2 and one for USB 3. In many cases the debugging is not tied to a HCD
>> in any way, (starting, stopping controller, command completion interrupts etc),
>> other cases the debugging is very much tied to a specific hcd,
>> for example when we are handling a port requsts for the roothub.
>
> A gentle ping...
>

Added to my for-usb-next branch, (which I'll need to rebase on 5.8-rc1 once released)

-Mathias

\
 
 \ /
  Last update: 2020-06-08 11:27    [W:0.082 / U:0.216 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site