lkml.org 
[lkml]   [2020]   [Jun]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH AUTOSEL 5.6 259/606] ARM: dts: omap4-droid4: Fix flakey wlan by disabling internal pull for gpio
Date
From: Tony Lindgren <tony@atomide.com>

[ Upstream commit 30fa60c678eaa27b8f2a531920d77f7184658f73 ]

The wlan on droid4 is flakey on some devices, and experiments have shown this
gets fixed if we disable the internal pull for wlan gpio interrupt line.

The symptoms are that the wlan connection is very slow and almost useless
with lots of wlcore firmware reboot warnings in the dmesg.

In addition to configuring the wlan gpio pulls, let's also configure the rest
of the wlan sd pins. We have not configured those eariler as we're booting
using kexec.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
.../boot/dts/motorola-mapphone-common.dtsi | 33 +++++++++++++++++++
1 file changed, 33 insertions(+)

diff --git a/arch/arm/boot/dts/motorola-mapphone-common.dtsi b/arch/arm/boot/dts/motorola-mapphone-common.dtsi
index 9067e0ef4240..01ea9a1e2c86 100644
--- a/arch/arm/boot/dts/motorola-mapphone-common.dtsi
+++ b/arch/arm/boot/dts/motorola-mapphone-common.dtsi
@@ -367,6 +367,8 @@ &mmc2 {
};

&mmc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins>;
vmmc-supply = <&wl12xx_vmmc>;
/* uart2_tx.sdmmc3_dat1 pad as wakeirq */
interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
@@ -472,6 +474,37 @@ OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0)
>;
};

+ /*
+ * Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3
+ * for gpio_100, but the internal pull makes wlan flakey on some
+ * devices. Off mode value should be tested if we have off mode working
+ * later on.
+ */
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ /* 0x4a10008e gpmc_wait2.gpio_100 d23 */
+ OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3)
+
+ /* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */
+ OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1)
+
+ /* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */
+ OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1)
+
+ /* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */
+ OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1)
+
+ /* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */
+ OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1)
+
+ /* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */
+ OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1)
+
+ /* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */
+ OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1)
+ >;
+ };
+
/* gpmc_ncs0.gpio_50 */
poweroff_gpio: pinmux_poweroff_pins {
pinctrl-single,pins = <
--
2.25.1
\
 
 \ /
  Last update: 2020-06-09 01:22    [W:0.897 / U:0.192 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site