lkml.org 
[lkml]   [2020]   [Jun]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 0/6] arm64: dts: qcom: smmu/USB nodes and HDK855/HDK865 dts
From
Date
On 6/4/20 11:58 AM, Manivannan Sadhasivam wrote:
> On Thu, Jun 04, 2020 at 10:06:19AM -0400, Jonathan Marek wrote:
>> On 6/4/20 9:52 AM, Manivannan Sadhasivam wrote:
>>> Hi,
>>>
>>> On Sat, May 23, 2020 at 10:38:06PM -0400, Jonathan Marek wrote:
>>>> Add dts nodes for apps_smmu and USB for both sm8150 and sm8250.
>>>>
>>>
>>> I've tested this series on an SM8250 based board and able to get Type C (USB0)
>>> working. There are also couple of Type A ports (USB1) on that board behind a
>>> USB hub. It is probing fine but I don't see any activity while connecting a
>>> USB device. Will continue to debug and once I get them working, I'll add my
>>> Tested-by tag.
>>>
>>
>> HDK865 also has a couple Type A ports, I am using them with devices already
>> plugged in during boot and I haven't hit a problem like that, but I think
>> I've seen the same issue when hotplugging. IIRC the behavior was a bit
>> weird, like plugging a device in the Type A port (USB1) nothing would
>> happen, but unplugging/replugging the type C port (USB0) would cause the
>> Type A port device to start working..
>>
>> Have you tried with the devices already plugged in before booting?
>>
>
> Tried it but no luck :/ Also plugging and removing Type C doesn't make any
> difference.
>

This one might be obvious, but do you have 5V power coming out of the
type A ports?

> Thanks,
> Mani
>
>>> Thanks,
>>> Mani
>>>
>>>> Also add initial dts files for HDK855 and HDK865, based on mtp dts, with a
>>>> few changes. Notably, the HDK865 dts has regulator config changed a bit based
>>>> on downstream (I think sm8250-mtp.dts is wrong and copied too much from sm8150).
>>>>
>>>> Jonathan Marek (6):
>>>> arm64: dts: qcom: sm8150: add apps_smmu node
>>>> arm64: dts: qcom: sm8250: add apps_smmu node
>>>> arm64: dts: qcom: sm8150: Add secondary USB and PHY nodes
>>>> arm64: dts: qcom: sm8250: Add USB and PHY device nodes
>>>> arm64: dts: qcom: add sm8150 hdk dts
>>>> arm64: dts: qcom: add sm8250 hdk dts
>>>>
>>>> arch/arm64/boot/dts/qcom/Makefile | 2 +
>>>> arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 461 ++++++++++++++++++++++++
>>>> arch/arm64/boot/dts/qcom/sm8150.dtsi | 180 +++++++++
>>>> arch/arm64/boot/dts/qcom/sm8250-hdk.dts | 454 +++++++++++++++++++++++
>>>> arch/arm64/boot/dts/qcom/sm8250.dtsi | 287 +++++++++++++++
>>>> 5 files changed, 1384 insertions(+)
>>>> create mode 100644 arch/arm64/boot/dts/qcom/sm8150-hdk.dts
>>>> create mode 100644 arch/arm64/boot/dts/qcom/sm8250-hdk.dts
>>>>
>>>> --
>>>> 2.26.1
>>>>

\
 
 \ /
  Last update: 2020-06-04 18:09    [W:0.123 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site