lkml.org 
[lkml]   [2020]   [Jun]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC 1/1] fpga: dfl: RFC PCI config
From
Date
On 6/30/20 10:16 AM, trix@redhat.com wrote:
> From: Tom Rix <trix@redhat.com>
>
> Create some top level configs the map to dfl pci cards.
>
> Autoselect the parts of fpga that are needed to run these cards
> as well as the other subsystem configs to the card's subdevices.
>
> Signed-off-by: Tom Rix <trix@redhat.com>
> ---
> Documentation/fpga/dfl.rst | 33 +++++++++++++++++++++++++++++++++
> drivers/fpga/Kconfig | 28 ++++++++++++++++++++++++++++
> 2 files changed, 61 insertions(+)
>
> diff --git a/Documentation/fpga/dfl.rst b/Documentation/fpga/dfl.rst
> index d7648d7c7eee..3a872bc8e3d3 100644
> --- a/Documentation/fpga/dfl.rst
> +++ b/Documentation/fpga/dfl.rst
> @@ -500,6 +500,39 @@ Developer only needs to provide a sub feature driver with matched feature id.
> FME Partial Reconfiguration Sub Feature driver (see drivers/fpga/dfl-fme-pr.c)
> could be a reference.
>
> +Kernel configuration
> +====================
> +
> +While it is possible to manually setup a configuration to match your device,
> +there are some top level configurations that collect configuations for

configurations

> +some reference pci cards. Below descibes these configuration as well as

PCI describes

> +what other kernel configs are needed for proper configuration.
> +
> +FPGA_DFL_PAC10
> +Intel Arria 10 GX PCI card, PCI id 0X09C4
> +Depends on
> + SPI_ALTERA
> + MFD_INTEL_M10_BMC
> + MFD_INTEL_M10_BMC_SECURE
> + SENSORS_INTEL_M10_BMC_HWMON
> +
> +FPGA_DFL_D5005
> +Intel Stratix 10, D5005 PCI card, PCI id 0X0B2B
> +Depends on
> + SPI_ALTERA
> + MFD_INTEL_M10_BMC
> + MFD_INTEL_M10_BMC_SECURE
> + SENSORS_INTEL_M10_BMC_HWMON
> + INTEL_S10_PHY
> +
> +FPGA_DFL_N3000
> +Intel Network Accelerator, N3000 PCI card, PCI id 0X0B30
> +Depends on
> + SPI_ALTERA
> + MFD_INTEL_M10_BMC
> + MFD_INTEL_M10_BMC_SECURE
> + SENSORS_INTEL_M10_BMC_HWMON
> + INTEL_LL_10G_MAC
>
> Open discussion
> ===============
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index 9d53bd9094e2..b657de20bc98 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -138,6 +138,34 @@ config OF_FPGA_REGION
> Support for loading FPGA images by applying a Device Tree
> overlay.
>
> +config FPGA_DFL_PAC10
> + tristate "Intel Arria 10 GX PCI card"
> + select SPI_ALTERA

above kconfig symbol:
depends on SPI_MASTER

> + select MFD_INTEL_M10_BMC
> + select MFD_INTEL_M10_BMC_SECURE
> + select SENSORS_INTEL_M10_BMC_HWMON

I haven't tested this, but in general it's not safe to select something like
SENSORS* or HWMON* unless you first check that CONFIG_HWMON is enabled.
Otherwise this would usually cause kconfig warning(s).

But don't add things like
select HWMON
select SPI
select SPI_MASTER

because we don't enable subsystems (like HWMON or SPI) just inside one
driver's kconfig entry.
The driver(s) should instead depend on HWMON, SPI, SPI_MASTER etc.

> + select FPGA_DFL
> + select FPGA_DFL_FME
> + select FPGA_DFL_FME_MGR
> + select FPGA_DFL_FME_BRIDGE
> + select FPGA_DFL_FME_REGION
> + select FPGA_DFL_AFU
> + select FPGA_DFL_SPI_ALTERA
> + select FPGA_DFL_PCI
> + select IFPGA_SEC_MGR
> +
> +config FPGA_DFL_D5005
> + tristate "Intel Stratix 10, D5005 PCI card"
> + select FPGA_DFL_PAC10
> + select INTEL_S10_PHY
> + select FPGA_DFl_HSSI
> +
> +config FPGA_DFL_N3000
> + tristate "Intel Network Accelerator, N3000 PCI card"
> + select FPGA_DFL_PAC10
> + select INTEL_LL_10G_MAC
> + select FPGA_DFL_N3000_NIOS
> +
> config FPGA_DFL
> tristate "FPGA Device Feature List (DFL) support"
> select FPGA_BRIDGE
>


--
~Randy

\
 
 \ /
  Last update: 2020-06-30 19:27    [W:0.041 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site