lkml.org 
[lkml]   [2020]   [Jun]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] SPI LPC information kernel module
On Tue, Jun 30, 2020 at 11:42:58AM -0300, Daniel Gutson wrote:
> On Tue, Jun 30, 2020 at 5:56 AM Greg Kroah-Hartman <
> gregkh@linuxfoundation.org> wrote:
>
> > On Mon, Jun 29, 2020 at 07:59:32PM -0300, Daniel Gutson wrote:
> > > This kernel module exports configuration attributes for the
> > > system SPI chip.
> > > This initial version exports the BIOS Write Enable (bioswe),
> > > BIOS Lock Enable (ble), and the SMM Bios Write Protect (SMM_BWP)
> > > fields of the Bios Control register. The idea is to keep adding more
> > > flags, not only from the BC but also from other registers in following
> > > versions.
> > >
> > > The goal is that the attributes are avilable to fwupd when SecureBoot
> > > is turned on.
> > >
> > > A technical note: I check if *ppos == BUFFER_SIZE in the reading function
> > > to exit early and avoid an extra access to the HW, for example when using
> > > the 'cat' command, which causes two read operations.
> >
> > Why not use the simple_* functions which should prevent that type of
> > thing?
> >
>
> a hint please? I don't see how to do it with simple_read_from_buffer, I
> need to return in the read fop the amount of read bytes, but don't know
> how to mark EOF. Because of that, 'cat' reads again just for me to tell it
> there's nothing else to read.

That's fine, the kernel does not tell userspace "EOF", that is up to the
libc to determine. If you read the data from the hardware once, and
keep it in your buffer, simple_read_from_buffer() will handle all of
that logic for you, please let it do that.

> > > Signed-off-by: Daniel Gutson <daniel.gutson@eclypsium.com>
> > > ---
> > > Documentation/ABI/stable/securityfs-spi-lpc | 23 +
> >
> > Why is this going in securityfs at all? Why not just sysfs as it is a
> > CPU attribute, right?
> >
>
> Richard already discussed that, but "it" is not only (one) CPU attribute,
> are SPI chip settings and attributes coming from the firmware.

All hardware things, please use sysfs, that is what it is designed for.

> Please note that I wanted to submit the minimum patch, but I need to add
> more attributes.

A patch series is great to create and send showing all of that.

> > > diff --git a/Documentation/ABI/stable/securityfs-spi-lpc
> > b/Documentation/ABI/stable/securityfs-spi-lpc
> > > new file mode 100644
> > > index 000000000000..22660a7fd914
> > > --- /dev/null
> > > +++ b/Documentation/ABI/stable/securityfs-spi-lpc
> > > @@ -0,0 +1,23 @@
> > > +What: /sys/kernel/security/firmware/bioswe
> > > +Date: June 2020
> > > +KernelVersion: 5.8.0
> > > +Contact: daniel.gutson@eclypsium.com
> > > +Description: If the system firmware set BIOS Write Enable.
> > > + 0: writes disabled, 1: writes enabled.
> >
> > THis is very x86-specific, what about ARM/MIPS/anything else? Perhaps a
> > cpu/arch-specific thing instead?
> >
>
> We debated this but didn't find a better match, since cpu/arch-specific
> seemed too core to put informational drivers.
> Do you have a suggestion?

Make it explicitly hardware specific in your userspace location.
Otherwise you just defined this for all hardware types, with what you
used above, and I do not think you wanted to do that.

> > Again, which makes it seem like securityfs is not the thing for this, as
> > it describes the hardware, not a security model which is what securityfs
> > has been for in the past, right?
> >
>
> I prefer to leave this to the other discussion with Richard. It's fine for
> me too to use sysfs.
> FWIW, the driver provides information related to firmware security.

It provides information on what is going on with the firmware, it's up
to userspace to know/determine/care if that means anything with regards
to "security" or not :)

thanks,

greg k-h

\
 
 \ /
  Last update: 2020-06-30 17:29    [W:1.908 / U:0.944 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site