lkml.org 
[lkml]   [2020]   [Jun]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 09/10] drm/ingenic: Add support for the IPU
Hi Sam,

Le mar. 30 juin 2020 à 14:16, Sam Ravnborg <sam@ravnborg.org> a écrit
:
> Hi Paul.
>
> On Tue, Jun 30, 2020 at 01:52:09AM +0200, Paul Cercueil wrote:
>> Add support for the Image Processing Unit (IPU) found in all Ingenic
>> SoCs.
>>
>> The IPU can upscale and downscale a source frame of arbitrary size
>> ranging from 4x4 to 4096x4096 on newer SoCs, with bicubic filtering
>> on newer SoCs, bilinear filtering on older SoCs. Nearest-neighbour
>> can
>> also be obtained with proper coefficients.
>>
>> Starting from the JZ4725B, the IPU supports a mode where its output
>> is
>> sent directly to the LCDC, without having to be written to RAM
>> first.
>> This makes it possible to use the IPU as a DRM plane on the
>> compatible
>> SoCs, and have it convert and scale anything the userspace asks for
>> to
>> what's available for the display.
>>
>> Regarding pixel formats, older SoCs support packed YUV 4:2:2 and
>> various
>> planar YUV formats. Newer SoCs introduced support for RGB.
>>
>
>> Since the IPU is a separate hardware block, to make it work
>> properly the
>> Ingenic DRM driver will now register itself as a component master in
>> case the IPU driver has been enabled in the config.
> I cannot see why this driver needs the component framework to deal
> with
> the IPU. It looks like a left-over from when this was two modules.
> While browsing the code the code now has two independent struct
> soc_info. It would be simpler with only one - at least if it is the
> same logic that is used in both cases.
>
> So open question - can this be simplified more than it is today and
> is the use of the component framework mandatory?
>
> Sam

The IPU IP is separate from the LCD controller. Its registers are in a
completely different area, it has its own clock, and interrupt line. It
has its own node in devicetree. As a result, you have one struct device
for the LCD controller, and one for the IPU.

Where it gets more complicated, is that the IPU driver needs a pointer
to the drm_device structure in order to register its drm_panel. When
the ingenic-drm driver calls component_bind_all(), it passes the
pointer, which allows the IPU plane to be created, which will be
retrieved by the ingenic-drm driver later on. There would be no way of
doing that in a clean manner without using the component framework.

Cheers,
-Paul

>>
>> When enabled in the config, the CRTC will see the IPU as a second
>> primary
>> plane. It cannot be enabled at the same time as the regular primary
>> plane. It has the same priority, which means that it will also
>> display
>> below the overlay plane.
>>
>> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
>> ---
>>
>> Notes:
>> v2: - ingenic-ipu is no longer its own module. It will be built
>> into the ingenic-drm module.
>> - If enabled in the config, both the core driver and the IPU
>> driver will register as components; otherwise the core
>> driver will bypass that and call the ingenic_drm_bind()
>> function directly.
>> - Since both files now build into the same module, the
>> symbols previously exported as GPL are not exported anymore,
>> since they are only used internally.
>> - Fix SPDX license header in ingenic-ipu.h
>> - Avoid using 'for(;;);' loops without trailing statement(s)
>>
>> drivers/gpu/drm/ingenic/Kconfig | 11 +
>> drivers/gpu/drm/ingenic/Makefile | 3 +-
>> drivers/gpu/drm/ingenic/ingenic-drm-drv.c | 155 +++-
>> drivers/gpu/drm/ingenic/ingenic-drm.h | 12 +
>> drivers/gpu/drm/ingenic/ingenic-ipu.c | 848
>> ++++++++++++++++++++++
>> drivers/gpu/drm/ingenic/ingenic-ipu.h | 109 +++
>> 6 files changed, 1122 insertions(+), 16 deletions(-)
>> create mode 100644 drivers/gpu/drm/ingenic/ingenic-ipu.c
>> create mode 100644 drivers/gpu/drm/ingenic/ingenic-ipu.h
>>
>> diff --git a/drivers/gpu/drm/ingenic/Kconfig
>> b/drivers/gpu/drm/ingenic/Kconfig
>> index d82c3d37ec9c..477d5387e43e 100644
>> --- a/drivers/gpu/drm/ingenic/Kconfig
>> +++ b/drivers/gpu/drm/ingenic/Kconfig
>> @@ -14,3 +14,14 @@ config DRM_INGENIC
>> Choose this option for DRM support for the Ingenic SoCs.
>>
>> If M is selected the module will be called ingenic-drm.
>> +
>> +if DRM_INGENIC
>> +
>> +config DRM_INGENIC_IPU
>> + bool "IPU support for Ingenic SoCs"
>> + help
>> + Choose this option to enable support for the IPU found in
>> Ingenic SoCs.
>> +
>> + The Image Processing Unit (IPU) will appear as a second primary
>> plane.
>> +
>> +endif
>> diff --git a/drivers/gpu/drm/ingenic/Makefile
>> b/drivers/gpu/drm/ingenic/Makefile
>> index 9875628dd8bc..d313326bdddb 100644
>> --- a/drivers/gpu/drm/ingenic/Makefile
>> +++ b/drivers/gpu/drm/ingenic/Makefile
>> @@ -1,2 +1,3 @@
>> obj-$(CONFIG_DRM_INGENIC) += ingenic-drm.o
>> -ingenic-drm-y += ingenic-drm-drv.o
>> +ingenic-drm-y = ingenic-drm-drv.o
>> +ingenic-drm-$(CONFIG_DRM_INGENIC_IPU) += ingenic-ipu.o
>> diff --git a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
>> b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
>> index a8573da1d577..36440acd23de 100644
>> --- a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
>> +++ b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
>> @@ -6,6 +6,7 @@
>>
>> #include "ingenic-drm.h"
>>
>> +#include <linux/component.h>
>> #include <linux/clk.h>
>> #include <linux/dma-mapping.h>
>> #include <linux/module.h>
>> @@ -49,7 +50,7 @@ struct jz_soc_info {
>>
>> struct ingenic_drm {
>> struct drm_device drm;
>> - struct drm_plane f0, f1;
>> + struct drm_plane f0, f1, *ipu_plane;
>> struct drm_crtc crtc;
>> struct drm_encoder encoder;
>>
>> @@ -185,13 +186,16 @@ static void
>> ingenic_drm_crtc_update_timings(struct ingenic_drm *priv,
>> regmap_update_bits(priv->map, JZ_REG_LCD_CTRL,
>> JZ_LCD_CTRL_OFUP | JZ_LCD_CTRL_BURST_16,
>> JZ_LCD_CTRL_OFUP | JZ_LCD_CTRL_BURST_16);
>> +
>> + regmap_write(priv->map, JZ_REG_LCD_IPUR, JZ_LCD_IPUR_IPUREN |
>> + (ht * vpe / 3) << JZ_LCD_IPUR_IPUR_LSB);
>> }
>>
>> static int ingenic_drm_crtc_atomic_check(struct drm_crtc *crtc,
>> struct drm_crtc_state *state)
>> {
>> struct ingenic_drm *priv = drm_crtc_get_priv(crtc);
>> - struct drm_plane_state *f1_state, *f0_state;
>> + struct drm_plane_state *f1_state, *f0_state, *ipu_state;
>> long rate;
>>
>> if (!drm_atomic_crtc_needs_modeset(state))
>> @@ -210,14 +214,40 @@ static int
>> ingenic_drm_crtc_atomic_check(struct drm_crtc *crtc,
>> f1_state = drm_atomic_get_plane_state(state->state, &priv->f1);
>> f0_state = drm_atomic_get_plane_state(state->state, &priv->f0);
>>
>> + if (priv->ipu_plane)
>> + ipu_state = drm_atomic_get_plane_state(state->state,
>> priv->ipu_plane);
>> +
>> + /* IPU and F1 planes cannot be enabled at the same time. */
>> + if (priv->ipu_plane && f1_state->fb && ipu_state->fb) {
>> + dev_dbg(priv->dev, "Cannot enable both F1 and IPU\n");
>> + return -EINVAL;
>> + }
>> +
>> /* If all the planes are disabled, we won't get a VBLANK IRQ */
>> - if (!f1_state->fb && !f0_state->fb)
>> + if (!f1_state->fb && !f0_state->fb &&
>> + !(priv->ipu_plane && ipu_state->fb))
>> state->no_vblank = true;
>> }
>>
>> return 0;
>> }
>>
>> +static void ingenic_drm_crtc_atomic_begin(struct drm_crtc *crtc,
>> + struct drm_crtc_state *oldstate)
>> +{
>> + struct ingenic_drm *priv = drm_crtc_get_priv(crtc);
>> + u32 ctrl = 0;
>> +
>> + if (priv->soc_info->has_osd &&
>> + drm_atomic_crtc_needs_modeset(crtc->state)) {
>> + if (priv->ipu_plane && priv->ipu_plane->state->fb)
>> + ctrl |= JZ_LCD_OSDCTRL_IPU;
>> +
>> + regmap_update_bits(priv->map, JZ_REG_LCD_OSDCTRL,
>> + JZ_LCD_OSDCTRL_IPU, ctrl);
>> + }
>> +}
>> +
>> static void ingenic_drm_crtc_atomic_flush(struct drm_crtc *crtc,
>> struct drm_crtc_state *oldstate)
>> {
>> @@ -303,10 +333,9 @@ static void ingenic_drm_plane_enable(struct
>> ingenic_drm *priv,
>> }
>> }
>>
>> -static void ingenic_drm_plane_atomic_disable(struct drm_plane
>> *plane,
>> - struct drm_plane_state *old_state)
>> +void ingenic_drm_plane_disable(struct device *dev, struct
>> drm_plane *plane)
>> {
>> - struct ingenic_drm *priv = drm_device_get_priv(plane->dev);
>> + struct ingenic_drm *priv = dev_get_drvdata(dev);
>> unsigned int en_bit;
>>
>> if (priv->soc_info->has_osd) {
>> @@ -319,9 +348,18 @@ static void
>> ingenic_drm_plane_atomic_disable(struct drm_plane *plane,
>> }
>> }
>>
>> -static void ingenic_drm_plane_config(struct ingenic_drm *priv,
>> - struct drm_plane *plane, u32 fourcc)
>> +static void ingenic_drm_plane_atomic_disable(struct drm_plane
>> *plane,
>> + struct drm_plane_state *old_state)
>> {
>> + struct ingenic_drm *priv = drm_device_get_priv(plane->dev);
>> +
>> + ingenic_drm_plane_disable(priv->dev, plane);
>> +}
>> +
>> +void ingenic_drm_plane_config(struct device *dev,
>> + struct drm_plane *plane, u32 fourcc)
>> +{
>> + struct ingenic_drm *priv = dev_get_drvdata(dev);
>> struct drm_plane_state *state = plane->state;
>> unsigned int xy_reg, size_reg;
>> unsigned int ctrl = 0;
>> @@ -404,7 +442,7 @@ static void
>> ingenic_drm_plane_atomic_update(struct drm_plane *plane,
>> priv->dma_hwdesc[hwdesc_idx]->cmd |= JZ_LCD_CMD_EOF_IRQ;
>>
>> if (drm_atomic_crtc_needs_modeset(state->crtc->state))
>> - ingenic_drm_plane_config(priv, plane,
>> + ingenic_drm_plane_config(priv->dev, plane,
>> state->fb->format->format);
>> }
>> }
>> @@ -574,6 +612,7 @@ static const struct drm_plane_helper_funcs
>> ingenic_drm_plane_helper_funcs = {
>> static const struct drm_crtc_helper_funcs
>> ingenic_drm_crtc_helper_funcs = {
>> .atomic_enable = ingenic_drm_crtc_atomic_enable,
>> .atomic_disable = ingenic_drm_crtc_atomic_disable,
>> + .atomic_begin = ingenic_drm_crtc_atomic_begin,
>> .atomic_flush = ingenic_drm_crtc_atomic_flush,
>> .atomic_check = ingenic_drm_crtc_atomic_check,
>> };
>> @@ -600,10 +639,17 @@ static void ingenic_drm_free_dma_hwdesc(void
>> *d)
>> priv->dma_hwdesc[1], priv->dma_hwdesc_phys[1]);
>> }
>>
>> -static int ingenic_drm_probe(struct platform_device *pdev)
>> +static void ingenic_drm_unbind_all(void *d)
>> +{
>> + struct ingenic_drm *priv = d;
>> +
>> + component_unbind_all(priv->dev, &priv->drm);
>> +}
>> +
>> +static int ingenic_drm_bind(struct device *dev)
>> {
>> + struct platform_device *pdev = to_platform_device(dev);
>> const struct jz_soc_info *soc_info;
>> - struct device *dev = &pdev->dev;
>> struct ingenic_drm *priv;
>> struct clk *parent_clk;
>> struct drm_bridge *bridge;
>> @@ -640,6 +686,19 @@ static int ingenic_drm_probe(struct
>> platform_device *pdev)
>> drm->mode_config.max_height = 4095;
>> drm->mode_config.funcs = &ingenic_drm_mode_config_funcs;
>>
>> + if (IS_ENABLED(CONFIG_DRM_INGENIC_IPU)) {
>> + ret = component_bind_all(dev, drm);
>> + if (ret) {
>> + if (ret != -EPROBE_DEFER)
>> + dev_err(dev, "Failed to bind components: %i\n", ret);
>> + return ret;
>> + }
>> +
>> + ret = devm_add_action_or_reset(dev, ingenic_drm_unbind_all,
>> priv);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> base = devm_platform_ioremap_resource(pdev, 0);
>> if (IS_ERR(base)) {
>> dev_err(dev, "Failed to get memory resource\n");
>> @@ -704,6 +763,9 @@ static int ingenic_drm_probe(struct
>> platform_device *pdev)
>> if (ret)
>> return ret;
>>
>> + if (soc_info->has_osd)
>> + priv->ipu_plane = drm_plane_from_index(drm, 0);
>> +
>> drm_plane_helper_add(&priv->f1, &ingenic_drm_plane_helper_funcs);
>>
>> ret = drm_universal_plane_init(drm, &priv->f1, 1,
>> @@ -712,7 +774,7 @@ static int ingenic_drm_probe(struct
>> platform_device *pdev)
>> ARRAY_SIZE(ingenic_drm_primary_formats),
>> NULL, DRM_PLANE_TYPE_PRIMARY, NULL);
>> if (ret) {
>> - dev_err(dev, "Failed to register primary plane: %i\n", ret);
>> + dev_err(dev, "Failed to register plane: %i\n", ret);
>> return ret;
>> }
>>
>> @@ -828,9 +890,14 @@ static int ingenic_drm_probe(struct
>> platform_device *pdev)
>> return ret;
>> }
>>
>> -static int ingenic_drm_remove(struct platform_device *pdev)
>> +static int compare_of(struct device *dev, void *data)
>> {
>> - struct ingenic_drm *priv = platform_get_drvdata(pdev);
>> + return dev->of_node == data;
>> +}
>> +
>> +static void ingenic_drm_unbind(struct device *dev)
>> +{
>> + struct ingenic_drm *priv = dev_get_drvdata(dev);
>>
>> if (priv->lcd_clk)
>> clk_disable_unprepare(priv->lcd_clk);
>> @@ -838,6 +905,42 @@ static int ingenic_drm_remove(struct
>> platform_device *pdev)
>>
>> drm_dev_unregister(&priv->drm);
>> drm_atomic_helper_shutdown(&priv->drm);
>> +}
>> +
>> +static const struct component_master_ops ingenic_master_ops = {
>> + .bind = ingenic_drm_bind,
>> + .unbind = ingenic_drm_unbind,
>> +};
>> +
>> +static int ingenic_drm_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct component_match *match = NULL;
>> + struct device_node *np;
>> +
>> + if (!IS_ENABLED(CONFIG_DRM_INGENIC_IPU))
>> + return ingenic_drm_bind(dev);
>> +
>> + /* IPU is at port address 8 */
>> + np = of_graph_get_remote_node(dev->of_node, 8, 0);
>> + if (!np) {
>> + dev_err(dev, "Unable to get IPU node\n");
>> + return -EINVAL;
>> + }
>> +
>> + drm_of_component_match_add(dev, &match, compare_of, np);
>> +
>> + return component_master_add_with_match(dev, &ingenic_master_ops,
>> match);
>> +}
>> +
>> +static int ingenic_drm_remove(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> +
>> + if (!IS_ENABLED(CONFIG_DRM_INGENIC_IPU))
>> + ingenic_drm_unbind(dev);
>> + else
>> + component_master_del(dev, &ingenic_master_ops);
>>
>> return 0;
>> }
>> @@ -879,7 +982,29 @@ static struct platform_driver
>> ingenic_drm_driver = {
>> .probe = ingenic_drm_probe,
>> .remove = ingenic_drm_remove,
>> };
>> -module_platform_driver(ingenic_drm_driver);
>> +
>> +static int ingenic_drm_init(void)
>> +{
>> + int err;
>> +
>> + if (IS_ENABLED(CONFIG_DRM_INGENIC_IPU)) {
>> + err = platform_driver_register(ingenic_ipu_driver_ptr);
>> + if (err)
>> + return err;
>> + }
>> +
>> + return platform_driver_register(&ingenic_drm_driver);
>> +}
>> +module_init(ingenic_drm_init);
>> +
>> +static void ingenic_drm_exit(void)
>> +{
>> + platform_driver_unregister(&ingenic_drm_driver);
>> +
>> + if (IS_ENABLED(CONFIG_DRM_INGENIC_IPU))
>> + platform_driver_unregister(ingenic_ipu_driver_ptr);
>> +}
>> +module_exit(ingenic_drm_exit);
>>
>> MODULE_AUTHOR("Paul Cercueil <paul@crapouillou.net>");
>> MODULE_DESCRIPTION("DRM driver for the Ingenic SoCs\n");
>> diff --git a/drivers/gpu/drm/ingenic/ingenic-drm.h
>> b/drivers/gpu/drm/ingenic/ingenic-drm.h
>> index d0b827a9fe83..43f7d959cff7 100644
>> --- a/drivers/gpu/drm/ingenic/ingenic-drm.h
>> +++ b/drivers/gpu/drm/ingenic/ingenic-drm.h
>> @@ -8,6 +8,7 @@
>> #define DRIVERS_GPU_DRM_INGENIC_INGENIC_DRM_H
>>
>> #include <linux/bitops.h>
>> +#include <linux/types.h>
>>
>> #define JZ_REG_LCD_CFG 0x00
>> #define JZ_REG_LCD_VSYNC 0x04
>> @@ -158,4 +159,15 @@
>> #define JZ_LCD_SIZE01_WIDTH_LSB 0
>> #define JZ_LCD_SIZE01_HEIGHT_LSB 16
>>
>> +struct device;
>> +struct drm_plane;
>> +struct drm_plane_state;
>> +struct platform_driver;
>> +
>> +void ingenic_drm_plane_config(struct device *dev,
>> + struct drm_plane *plane, u32 fourcc);
>> +void ingenic_drm_plane_disable(struct device *dev, struct
>> drm_plane *plane);
>> +
>> +extern struct platform_driver *ingenic_ipu_driver_ptr;
>> +
>> #endif /* DRIVERS_GPU_DRM_INGENIC_INGENIC_DRM_H */
>> diff --git a/drivers/gpu/drm/ingenic/ingenic-ipu.c
>> b/drivers/gpu/drm/ingenic/ingenic-ipu.c
>> new file mode 100644
>> index 000000000000..df7eb72df887
>> --- /dev/null
>> +++ b/drivers/gpu/drm/ingenic/ingenic-ipu.c
>> @@ -0,0 +1,848 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +//
>> +// Ingenic JZ47xx IPU driver
>> +//
>> +// Copyright (C) 2020, Paul Cercueil <paul@crapouillou.net>
>> +
>> +#include "ingenic-drm.h"
>> +#include "ingenic-ipu.h"
>> +
>> +#include <linux/clk.h>
>> +#include <linux/component.h>
>> +#include <linux/gcd.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_device.h>
>> +#include <linux/regmap.h>
>> +#include <linux/time.h>
>> +
>> +#include <drm/drm_atomic.h>
>> +#include <drm/drm_atomic_helper.h>
>> +#include <drm/drm_drv.h>
>> +#include <drm/drm_fb_cma_helper.h>
>> +#include <drm/drm_fourcc.h>
>> +#include <drm/drm_gem_framebuffer_helper.h>
>> +#include <drm/drm_plane.h>
>> +#include <drm/drm_plane_helper.h>
>> +#include <drm/drm_property.h>
>> +#include <drm/drm_vblank.h>
>> +
>> +struct ingenic_ipu;
>> +
>> +struct soc_info {
>> + const u32 *formats;
>> + size_t num_formats;
>> + bool has_bicubic;
>> +
>> + void (*set_coefs)(struct ingenic_ipu *ipu, unsigned int reg,
>> + unsigned int sharpness, bool downscale,
>> + unsigned int weight, unsigned int offset);
>> +};
>> +
>> +struct ingenic_ipu {
>> + struct drm_plane plane;
>> + struct device *dev, *master;
>> + struct regmap *map;
>> + struct clk *clk;
>> + const struct soc_info *soc_info;
>> +
>> + unsigned int numW, numH, denomW, denomH;
>> +
>> + struct drm_property *sharpness_prop;
>> + unsigned int sharpness;
>> +};
>> +
>> +/* Signed 15.16 fixed-point math (for bicubic scaling
>> coefficients) */
>> +#define I2F(i) ((s32)(i) * 65536)
>> +#define F2I(f) ((f) / 65536)
>> +#define FMUL(fa, fb) ((s32)(((s64)(fa) * (s64)(fb)) / 65536))
>> +#define SHARPNESS_INCR (I2F(-1) / 8)
>> +
>> +static inline struct ingenic_ipu *plane_to_ingenic_ipu(struct
>> drm_plane *plane)
>> +{
>> + return container_of(plane, struct ingenic_ipu, plane);
>> +}
>> +
>> +/*
>> + * Apply conventional cubic convolution kernel. Both parameters
>> + * and return value are 15.16 signed fixed-point.
>> + *
>> + * @f_a: Sharpness factor, typically in range [-4.0, -0.25].
>> + * A larger magnitude increases perceived sharpness, but
>> going past
>> + * -2.0 might cause ringing artifacts to outweigh any
>> improvement.
>> + * Nice values on a 320x240 LCD are between -0.75 and -2.0.
>> + *
>> + * @f_x: Absolute distance in pixels from 'pixel 0' sample
>> position
>> + * along horizontal (or vertical) source axis. Range is [0,
>> +2.0].
>> + *
>> + * returns: Weight of this pixel within 4-pixel sample group.
>> Range is
>> + * [-2.0, +2.0]. For moderate (i.e. > -3.0) sharpness
>> factors,
>> + * range is within [-1.0, +1.0].
>> + */
>> +static inline s32 cubic_conv(s32 f_a, s32 f_x)
>> +{
>> + const s32 f_1 = I2F(1);
>> + const s32 f_2 = I2F(2);
>> + const s32 f_3 = I2F(3);
>> + const s32 f_4 = I2F(4);
>> + const s32 f_x2 = FMUL(f_x, f_x);
>> + const s32 f_x3 = FMUL(f_x, f_x2);
>> +
>> + if (f_x <= f_1)
>> + return FMUL((f_a + f_2), f_x3) - FMUL((f_a + f_3), f_x2) + f_1;
>> + else if (f_x <= f_2)
>> + return FMUL(f_a, (f_x3 - 5 * f_x2 + 8 * f_x - f_4));
>> + else
>> + return 0;
>> +}
>> +
>> +/*
>> + * On entry, "weight" is a coefficient suitable for bilinear mode,
>> + * which is converted to a set of four suitable for bicubic mode.
>> + *
>> + * "weight 512" means all of pixel 0;
>> + * "weight 256" means half of pixel 0 and half of pixel 1;
>> + * "weight 0" means all of pixel 1;
>> + *
>> + * "offset" is increment to next source pixel sample location.
>> + */
>> +static void jz4760_set_coefs(struct ingenic_ipu *ipu, unsigned int
>> reg,
>> + unsigned int sharpness, bool downscale,
>> + unsigned int weight, unsigned int offset)
>> +{
>> + u32 val;
>> + s32 w0, w1, w2, w3; /* Pixel weights at X (or Y) offsets -1,0,1,2
>> */
>> +
>> + weight = clamp_val(weight, 0, 512);
>> +
>> + if (sharpness < 2) {
>> + /*
>> + * When sharpness setting is 0, emulate nearest-neighbor.
>> + * When sharpness setting is 1, emulate bilinear.
>> + */
>> +
>> + if (sharpness == 0)
>> + weight = weight >= 256 ? 512 : 0;
>> + w0 = 0;
>> + w1 = weight;
>> + w2 = 512 - weight;
>> + w3 = 0;
>> + } else {
>> + const s32 f_a = SHARPNESS_INCR * sharpness;
>> + const s32 f_h = I2F(1) / 2; /* Round up 0.5 */
>> +
>> + /*
>> + * Note that always rounding towards +infinity here is intended.
>> + * The resulting coefficients match a round-to-nearest-int
>> + * double floating-point implementation.
>> + */
>> +
>> + weight = 512 - weight;
>> + w0 = F2I(f_h + 512 * cubic_conv(f_a, I2F(512 + weight) / 512));
>> + w1 = F2I(f_h + 512 * cubic_conv(f_a, I2F(0 + weight) / 512));
>> + w2 = F2I(f_h + 512 * cubic_conv(f_a, I2F(512 - weight) / 512));
>> + w3 = F2I(f_h + 512 * cubic_conv(f_a, I2F(1024 - weight) / 512));
>> + w0 = clamp_val(w0, -1024, 1023);
>> + w1 = clamp_val(w1, -1024, 1023);
>> + w2 = clamp_val(w2, -1024, 1023);
>> + w3 = clamp_val(w3, -1024, 1023);
>> + }
>> +
>> + val = ((w1 & JZ4760_IPU_RSZ_COEF_MASK) <<
>> JZ4760_IPU_RSZ_COEF31_LSB) |
>> + ((w0 & JZ4760_IPU_RSZ_COEF_MASK) << JZ4760_IPU_RSZ_COEF20_LSB);
>> + regmap_write(ipu->map, reg, val);
>> +
>> + val = ((w3 & JZ4760_IPU_RSZ_COEF_MASK) <<
>> JZ4760_IPU_RSZ_COEF31_LSB) |
>> + ((w2 & JZ4760_IPU_RSZ_COEF_MASK) << JZ4760_IPU_RSZ_COEF20_LSB) |
>> + ((offset & JZ4760_IPU_RSZ_OFFSET_MASK) <<
>> JZ4760_IPU_RSZ_OFFSET_LSB);
>> + regmap_write(ipu->map, reg, val);
>> +}
>> +
>> +static void jz4725b_set_coefs(struct ingenic_ipu *ipu, unsigned
>> int reg,
>> + unsigned int sharpness, bool downscale,
>> + unsigned int weight, unsigned int offset)
>> +{
>> + u32 val = JZ4725B_IPU_RSZ_LUT_OUT_EN;
>> + unsigned int i;
>> +
>> + weight = clamp_val(weight, 0, 512);
>> +
>> + if (sharpness == 0)
>> + weight = weight >= 256 ? 512 : 0;
>> +
>> + val |= (weight & JZ4725B_IPU_RSZ_LUT_COEF_MASK) <<
>> JZ4725B_IPU_RSZ_LUT_COEF_LSB;
>> + if (downscale || !!offset)
>> + val |= JZ4725B_IPU_RSZ_LUT_IN_EN;
>> +
>> + regmap_write(ipu->map, reg, val);
>> +
>> + if (downscale) {
>> + for (i = 1; i < offset; i++)
>> + regmap_write(ipu->map, reg, JZ4725B_IPU_RSZ_LUT_IN_EN);
>> + }
>> +}
>> +
>> +static void ingenic_ipu_set_downscale_coefs(struct ingenic_ipu
>> *ipu,
>> + unsigned int reg,
>> + unsigned int num,
>> + unsigned int denom)
>> +{
>> + unsigned int i, offset, weight, weight_num = denom;
>> +
>> + for (i = 0; i < num; i++) {
>> + weight_num = num + (weight_num - num) % (num * 2);
>> + weight = 512 - 512 * (weight_num - num) / (num * 2);
>> + weight_num += denom * 2;
>> + offset = (weight_num - num) / (num * 2);
>> +
>> + ipu->soc_info->set_coefs(ipu, reg, ipu->sharpness,
>> + true, weight, offset);
>> + }
>> +}
>> +
>> +static void ingenic_ipu_set_integer_upscale_coefs(struct
>> ingenic_ipu *ipu,
>> + unsigned int reg,
>> + unsigned int num)
>> +{
>> + /*
>> + * Force nearest-neighbor scaling and use simple math when
>> upscaling
>> + * by an integer ratio. It looks better, and fixes a few problem
>> cases.
>> + */
>> + unsigned int i;
>> +
>> + for (i = 0; i < num; i++)
>> + ipu->soc_info->set_coefs(ipu, reg, 0, false, 512, i == num - 1);
>> +}
>> +
>> +static void ingenic_ipu_set_upscale_coefs(struct ingenic_ipu *ipu,
>> + unsigned int reg,
>> + unsigned int num,
>> + unsigned int denom)
>> +{
>> + unsigned int i, offset, weight, weight_num = 0;
>> +
>> + for (i = 0; i < num; i++) {
>> + weight = 512 - 512 * weight_num / num;
>> + weight_num += denom;
>> + offset = weight_num >= num;
>> +
>> + if (offset)
>> + weight_num -= num;
>> +
>> + ipu->soc_info->set_coefs(ipu, reg, ipu->sharpness,
>> + false, weight, offset);
>> + }
>> +}
>> +
>> +static void ingenic_ipu_set_coefs(struct ingenic_ipu *ipu,
>> unsigned int reg,
>> + unsigned int num, unsigned int denom)
>> +{
>> + /* Begin programming the LUT */
>> + regmap_write(ipu->map, reg, -1);
>> +
>> + if (denom > num)
>> + ingenic_ipu_set_downscale_coefs(ipu, reg, num, denom);
>> + else if (denom == 1)
>> + ingenic_ipu_set_integer_upscale_coefs(ipu, reg, num);
>> + else
>> + ingenic_ipu_set_upscale_coefs(ipu, reg, num, denom);
>> +}
>> +
>> +static int reduce_fraction(unsigned int *num, unsigned int *denom)
>> +{
>> + unsigned long d = gcd(*num, *denom);
>> +
>> + /* The scaling table has only 31 entries */
>> + if (*num > 31 * d)
>> + return -EINVAL;
>> +
>> + *num /= d;
>> + *denom /= d;
>> + return 0;
>> +}
>> +
>> +static inline bool scaling_required(struct drm_plane_state *state)
>> +{
>> + return (state->src_w >> 16) != state->crtc_w &&
>> + (state->src_h >> 16) != state->crtc_h;
>> +}
>> +
>> +static inline bool osd_changed(struct drm_plane_state *state,
>> + struct drm_plane_state *oldstate)
>> +{
>> + return state->crtc_x != oldstate->crtc_x ||
>> + state->crtc_y != oldstate->crtc_y ||
>> + state->crtc_w != oldstate->crtc_w ||
>> + state->crtc_h != oldstate->crtc_h;
>> +}
>> +
>> +static void ingenic_ipu_plane_atomic_update(struct drm_plane
>> *plane,
>> + struct drm_plane_state *oldstate)
>> +{
>> + struct ingenic_ipu *ipu = plane_to_ingenic_ipu(plane);
>> + struct drm_plane_state *state = plane->state;
>> + const struct drm_format_info *finfo;
>> + u32 ctrl, stride = 0, coef_index = 0, format = 0;
>> + bool needs_modeset, upscaling_w, upscaling_h;
>> + dma_addr_t addr;
>> +
>> + if (!state || !state->fb)
>> + return;
>> +
>> + finfo = drm_format_info(state->fb->format->format);
>> +
>> + /* Reset all the registers if needed */
>> + needs_modeset = drm_atomic_crtc_needs_modeset(state->crtc->state);
>> + if (needs_modeset)
>> + regmap_set_bits(ipu->map, JZ_REG_IPU_CTRL, JZ_IPU_CTRL_RST);
>> +
>> + /* Enable the chip */
>> + regmap_set_bits(ipu->map, JZ_REG_IPU_CTRL, JZ_IPU_CTRL_CHIP_EN);
>> +
>> + /* Set addresses */
>> + if (finfo->num_planes > 2) {
>> + addr = drm_fb_cma_get_gem_addr(state->fb, state, 2);
>> + regmap_write(ipu->map, JZ_REG_IPU_V_ADDR, addr);
>> + }
>> +
>> + if (finfo->num_planes > 1) {
>> + addr = drm_fb_cma_get_gem_addr(state->fb, state, 1);
>> + regmap_write(ipu->map, JZ_REG_IPU_U_ADDR, addr);
>> + }
>> +
>> + addr = drm_fb_cma_get_gem_addr(state->fb, state, 0);
>> + regmap_write(ipu->map, JZ_REG_IPU_Y_ADDR, addr);
>> +
>> + if (!needs_modeset)
>> + return;
>> +
>> + ingenic_drm_plane_config(ipu->master, plane, DRM_FORMAT_XRGB8888);
>> +
>> + /* Set the input height/width/strides */
>> + if (finfo->num_planes > 2)
>> + stride = ((state->src_w >> 16) * finfo->cpp[2] / finfo->hsub)
>> + << JZ_IPU_UV_STRIDE_V_LSB;
>> +
>> + if (finfo->num_planes > 1)
>> + stride |= ((state->src_w >> 16) * finfo->cpp[1] / finfo->hsub)
>> + << JZ_IPU_UV_STRIDE_U_LSB;
>> +
>> + regmap_write(ipu->map, JZ_REG_IPU_UV_STRIDE, stride);
>> +
>> + stride = ((state->src_w >> 16) * finfo->cpp[0])
>> + << JZ_IPU_Y_STRIDE_Y_LSB;
>> + regmap_write(ipu->map, JZ_REG_IPU_Y_STRIDE, stride);
>> +
>> + regmap_write(ipu->map, JZ_REG_IPU_IN_GS,
>> + (stride << JZ_IPU_IN_GS_W_LSB) |
>> + ((state->src_h >> 16) << JZ_IPU_IN_GS_H_LSB));
>> +
>> + switch (finfo->format) {
>> + case DRM_FORMAT_XRGB1555:
>> + format = JZ_IPU_D_FMT_IN_FMT_RGB555 |
>> + JZ_IPU_D_FMT_RGB_OUT_OFT_RGB;
>> + break;
>> + case DRM_FORMAT_XBGR1555:
>> + format = JZ_IPU_D_FMT_IN_FMT_RGB555 |
>> + JZ_IPU_D_FMT_RGB_OUT_OFT_BGR;
>> + break;
>> + case DRM_FORMAT_RGB565:
>> + format = JZ_IPU_D_FMT_IN_FMT_RGB565 |
>> + JZ_IPU_D_FMT_RGB_OUT_OFT_RGB;
>> + break;
>> + case DRM_FORMAT_BGR565:
>> + format = JZ_IPU_D_FMT_IN_FMT_RGB565 |
>> + JZ_IPU_D_FMT_RGB_OUT_OFT_BGR;
>> + break;
>> + case DRM_FORMAT_XRGB8888:
>> + format = JZ_IPU_D_FMT_IN_FMT_RGB888 |
>> + JZ_IPU_D_FMT_RGB_OUT_OFT_RGB;
>> + break;
>> + case DRM_FORMAT_XBGR8888:
>> + format = JZ_IPU_D_FMT_IN_FMT_RGB888 |
>> + JZ_IPU_D_FMT_RGB_OUT_OFT_BGR;
>> + break;
>> + case DRM_FORMAT_YUYV:
>> + format = JZ_IPU_D_FMT_IN_FMT_YUV422 |
>> + JZ_IPU_D_FMT_YUV_VY1UY0;
>> + break;
>> + case DRM_FORMAT_YVYU:
>> + format = JZ_IPU_D_FMT_IN_FMT_YUV422 |
>> + JZ_IPU_D_FMT_YUV_UY1VY0;
>> + break;
>> + case DRM_FORMAT_UYVY:
>> + format = JZ_IPU_D_FMT_IN_FMT_YUV422 |
>> + JZ_IPU_D_FMT_YUV_Y1VY0U;
>> + break;
>> + case DRM_FORMAT_VYUY:
>> + format = JZ_IPU_D_FMT_IN_FMT_YUV422 |
>> + JZ_IPU_D_FMT_YUV_Y1UY0V;
>> + break;
>> + case DRM_FORMAT_YUV411:
>> + format = JZ_IPU_D_FMT_IN_FMT_YUV411;
>> + break;
>> + case DRM_FORMAT_YUV420:
>> + format = JZ_IPU_D_FMT_IN_FMT_YUV420;
>> + break;
>> + case DRM_FORMAT_YUV422:
>> + format = JZ_IPU_D_FMT_IN_FMT_YUV422;
>> + break;
>> + case DRM_FORMAT_YUV444:
>> + format = JZ_IPU_D_FMT_IN_FMT_YUV444;
>> + break;
>> + default:
>> + WARN_ONCE(1, "Unsupported format");
>> + break;
>> + }
>> +
>> + /* Fix output to RGB888 */
>> + format |= JZ_IPU_D_FMT_OUT_FMT_RGB888;
>> +
>> + /* Set pixel format */
>> + regmap_write(ipu->map, JZ_REG_IPU_D_FMT, format);
>> +
>> + /* Set the output height/width/stride */
>> + regmap_write(ipu->map, JZ_REG_IPU_OUT_GS,
>> + ((state->crtc_w * 4) << JZ_IPU_OUT_GS_W_LSB)
>> + | state->crtc_h << JZ_IPU_OUT_GS_H_LSB);
>> + regmap_write(ipu->map, JZ_REG_IPU_OUT_STRIDE, state->crtc_w * 4);
>> +
>> + ctrl = JZ_IPU_CTRL_LCDC_SEL | JZ_IPU_CTRL_FM_IRQ_EN;
>> +
>> + if (finfo->num_planes == 1)
>> + ctrl |= JZ_IPU_CTRL_SPKG_SEL;
>> + if (finfo->is_yuv)
>> + ctrl |= JZ_IPU_CTRL_CSC_EN;
>> +
>> + regmap_update_bits(ipu->map, JZ_REG_IPU_CTRL,
>> + JZ_IPU_CTRL_LCDC_SEL | JZ_IPU_CTRL_FM_IRQ_EN |
>> + JZ_IPU_CTRL_SPKG_SEL | JZ_IPU_CTRL_CSC_EN, ctrl);
>> +
>> + if (finfo->is_yuv) {
>> + /*
>> + * Offsets for Chroma/Luma.
>> + * y = source Y - LUMA,
>> + * u = source Cb - CHROMA,
>> + * v = source Cr - CHROMA
>> + */
>> + regmap_write(ipu->map, JZ_REG_IPU_CSC_OFFSET,
>> + 128 << JZ_IPU_CSC_OFFSET_CHROMA_LSB |
>> + 0 << JZ_IPU_CSC_OFFSET_LUMA_LSB);
>> +
>> + /*
>> + * YUV422 to RGB conversion table.
>> + * R = C0 / 0x400 * y + C1 / 0x400 * v
>> + * G = C0 / 0x400 * y - C2 / 0x400 * u - C3 / 0x400 * v
>> + * B = C0 / 0x400 * y + C4 / 0x400 * u
>> + */
>> + regmap_write(ipu->map, JZ_REG_IPU_CSC_C0_COEF, 0x4a8);
>> + regmap_write(ipu->map, JZ_REG_IPU_CSC_C1_COEF, 0x662);
>> + regmap_write(ipu->map, JZ_REG_IPU_CSC_C2_COEF, 0x191);
>> + regmap_write(ipu->map, JZ_REG_IPU_CSC_C3_COEF, 0x341);
>> + regmap_write(ipu->map, JZ_REG_IPU_CSC_C4_COEF, 0x811);
>> + }
>> +
>> + ctrl = 0;
>> +
>> + /*
>> + * Must set ZOOM_SEL before programming bicubic LUTs.
>> + * If the IPU supports bicubic, we enable it unconditionally,
>> since it
>> + * can do anything bilinear can and more.
>> + */
>> + if (ipu->soc_info->has_bicubic)
>> + ctrl |= JZ_IPU_CTRL_ZOOM_SEL;
>> +
>> + upscaling_w = ipu->numW > ipu->denomW;
>> + if (upscaling_w)
>> + ctrl |= JZ_IPU_CTRL_HSCALE;
>> +
>> + if (ipu->numW != 1 || ipu->denomW != 1) {
>> + if (!ipu->soc_info->has_bicubic && !upscaling_w)
>> + coef_index |= (ipu->denomW - 1) << 16;
>> + else
>> + coef_index |= (ipu->numW - 1) << 16;
>> + ctrl |= JZ_IPU_CTRL_HRSZ_EN;
>> + }
>> +
>> + upscaling_h = ipu->numH > ipu->denomH;
>> + if (upscaling_h)
>> + ctrl |= JZ_IPU_CTRL_VSCALE;
>> +
>> + if (ipu->numH != 1 || ipu->denomH != 1) {
>> + if (!ipu->soc_info->has_bicubic && !upscaling_h)
>> + coef_index |= ipu->denomH - 1;
>> + else
>> + coef_index |= ipu->numH - 1;
>> + ctrl |= JZ_IPU_CTRL_VRSZ_EN;
>> + }
>> +
>> + regmap_update_bits(ipu->map, JZ_REG_IPU_CTRL,
>> JZ_IPU_CTRL_ZOOM_SEL |
>> + JZ_IPU_CTRL_HRSZ_EN | JZ_IPU_CTRL_VRSZ_EN |
>> + JZ_IPU_CTRL_HSCALE | JZ_IPU_CTRL_VSCALE, ctrl);
>> +
>> + /* Set the LUT index register */
>> + regmap_write(ipu->map, JZ_REG_IPU_RSZ_COEF_INDEX, coef_index);
>> +
>> + if (ipu->numW != 1 || ipu->denomW != 1)
>> + ingenic_ipu_set_coefs(ipu, JZ_REG_IPU_HRSZ_COEF_LUT,
>> + ipu->numW, ipu->denomW);
>> +
>> + if (ipu->numH != 1 || ipu->denomH != 1)
>> + ingenic_ipu_set_coefs(ipu, JZ_REG_IPU_VRSZ_COEF_LUT,
>> + ipu->numH, ipu->denomH);
>> +
>> + /* Clear STATUS register */
>> + regmap_write(ipu->map, JZ_REG_IPU_STATUS, 0);
>> +
>> + /* Start IPU */
>> + regmap_set_bits(ipu->map, JZ_REG_IPU_CTRL, JZ_IPU_CTRL_RUN);
>> +
>> + dev_dbg(ipu->dev, "Scaling %ux%u to %ux%u (%u:%u horiz, %u:%u
>> vert)\n",
>> + state->src_w >> 16, state->src_h >> 16,
>> + state->crtc_w, state->crtc_h,
>> + ipu->numW, ipu->denomW, ipu->numH, ipu->denomH);
>> +}
>> +
>> +static int ingenic_ipu_plane_atomic_check(struct drm_plane *plane,
>> + struct drm_plane_state *state)
>> +{
>> + unsigned int numW, denomW, numH, denomH, xres, yres;
>> + struct ingenic_ipu *ipu = plane_to_ingenic_ipu(plane);
>> + struct drm_crtc *crtc = state->crtc ?: plane->state->crtc;
>> + struct drm_crtc_state *crtc_state;
>> +
>> + if (!crtc)
>> + return 0;
>> +
>> + crtc_state = drm_atomic_get_existing_crtc_state(state->state,
>> crtc);
>> + if (WARN_ON(!crtc_state))
>> + return -EINVAL;
>> +
>> + /* Request a full modeset if we are enabling or disabling the
>> IPU. */
>> + if (!plane->state->crtc ^ !state->crtc)
>> + crtc_state->mode_changed = true;
>> +
>> + if (!state->crtc ||
>> + !crtc_state->mode.hdisplay || !crtc_state->mode.vdisplay)
>> + return 0;
>> +
>> + /* Plane must be fully visible */
>> + if (state->crtc_x < 0 || state->crtc_y < 0 ||
>> + state->crtc_x + state->crtc_w > crtc_state->mode.hdisplay ||
>> + state->crtc_y + state->crtc_h > crtc_state->mode.vdisplay)
>> + return -EINVAL;
>> +
>> + /* Minimum size is 4x4 */
>> + if ((state->src_w >> 16) < 4 || (state->src_h >> 16) < 4)
>> + return -EINVAL;
>> +
>> + /* Input and output lines must have an even number of pixels. */
>> + if (((state->src_w >> 16) & 1) || (state->crtc_w & 1))
>> + return -EINVAL;
>> +
>> + if (!scaling_required(state)) {
>> + if (plane->state && osd_changed(state, plane->state))
>> + crtc_state->mode_changed = true;
>> +
>> + ipu->numW = ipu->numH = ipu->denomW = ipu->denomH = 1;
>> + return 0;
>> + }
>> +
>> + crtc_state->mode_changed = true;
>> +
>> + xres = state->src_w >> 16;
>> + yres = state->src_h >> 16;
>> +
>> + /* Adjust the coefficients until we find a valid configuration */
>> + for (denomW = xres, numW = state->crtc_w;
>> + numW <= crtc_state->mode.hdisplay; numW++)
>> + if (!reduce_fraction(&numW, &denomW))
>> + break;
>> + if (numW > crtc_state->mode.hdisplay)
>> + return -EINVAL;
>> +
>> + for (denomH = yres, numH = state->crtc_h;
>> + numH <= crtc_state->mode.vdisplay; numH++)
>> + if (!reduce_fraction(&numH, &denomH))
>> + break;
>> + if (numH > crtc_state->mode.vdisplay)
>> + return -EINVAL;
>> +
>> + ipu->numW = numW;
>> + ipu->numH = numH;
>> + ipu->denomW = denomW;
>> + ipu->denomH = denomH;
>> +
>> + return 0;
>> +}
>> +
>> +static void ingenic_ipu_plane_atomic_disable(struct drm_plane
>> *plane,
>> + struct drm_plane_state *old_state)
>> +{
>> + struct ingenic_ipu *ipu = plane_to_ingenic_ipu(plane);
>> +
>> + regmap_set_bits(ipu->map, JZ_REG_IPU_CTRL, JZ_IPU_CTRL_STOP);
>> + regmap_clear_bits(ipu->map, JZ_REG_IPU_CTRL, JZ_IPU_CTRL_CHIP_EN);
>> +
>> + ingenic_drm_plane_disable(ipu->master, plane);
>> +}
>> +
>> +static const struct drm_plane_helper_funcs
>> ingenic_ipu_plane_helper_funcs = {
>> + .atomic_update = ingenic_ipu_plane_atomic_update,
>> + .atomic_check = ingenic_ipu_plane_atomic_check,
>> + .atomic_disable = ingenic_ipu_plane_atomic_disable,
>> + .prepare_fb = drm_gem_fb_prepare_fb,
>> +};
>> +
>> +static int
>> +ingenic_ipu_plane_atomic_get_property(struct drm_plane *plane,
>> + const struct drm_plane_state *state,
>> + struct drm_property *property, u64 *val)
>> +{
>> + struct ingenic_ipu *ipu = plane_to_ingenic_ipu(plane);
>> +
>> + if (property != ipu->sharpness_prop)
>> + return -EINVAL;
>> +
>> + *val = ipu->sharpness;
>> +
>> + return 0;
>> +}
>> +
>> +static int
>> +ingenic_ipu_plane_atomic_set_property(struct drm_plane *plane,
>> + struct drm_plane_state *state,
>> + struct drm_property *property, u64 val)
>> +{
>> + struct ingenic_ipu *ipu = plane_to_ingenic_ipu(plane);
>> + struct drm_crtc_state *crtc_state;
>> +
>> + if (property != ipu->sharpness_prop)
>> + return -EINVAL;
>> +
>> + ipu->sharpness = val;
>> +
>> + if (state->crtc) {
>> + crtc_state = drm_atomic_get_existing_crtc_state(state->state,
>> state->crtc);
>> + if (WARN_ON(!crtc_state))
>> + return -EINVAL;
>> +
>> + crtc_state->mode_changed = true;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static const struct drm_plane_funcs ingenic_ipu_plane_funcs = {
>> + .update_plane = drm_atomic_helper_update_plane,
>> + .disable_plane = drm_atomic_helper_disable_plane,
>> + .reset = drm_atomic_helper_plane_reset,
>> + .destroy = drm_plane_cleanup,
>> +
>> + .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state,
>> + .atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
>> +
>> + .atomic_get_property = ingenic_ipu_plane_atomic_get_property,
>> + .atomic_set_property = ingenic_ipu_plane_atomic_set_property,
>> +};
>> +
>> +static irqreturn_t ingenic_ipu_irq_handler(int irq, void *arg)
>> +{
>> + struct drm_plane *plane = drm_plane_from_index(arg, 0);
>> + struct ingenic_ipu *ipu = plane_to_ingenic_ipu(plane);
>> + struct drm_crtc *crtc = drm_crtc_from_index(arg, 0);
>> +
>> + regmap_write(ipu->map, JZ_REG_IPU_STATUS, 0);
>> +
>> + drm_crtc_handle_vblank(crtc);
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +static const struct regmap_config ingenic_ipu_regmap_config = {
>> + .reg_bits = 32,
>> + .val_bits = 32,
>> + .reg_stride = 4,
>> +
>> + .max_register = JZ_REG_IPU_OUT_PHY_T_ADDR,
>> +};
>> +
>> +static int ingenic_ipu_bind(struct device *dev, struct device
>> *master, void *d)
>> +{
>> + struct platform_device *pdev = to_platform_device(dev);
>> + const struct soc_info *soc_info;
>> + struct drm_device *drm = d;
>> + struct drm_plane *plane;
>> + struct ingenic_ipu *ipu;
>> + void __iomem *base;
>> + unsigned int sharpness_max;
>> + int err, irq;
>> +
>> + ipu = devm_kzalloc(dev, sizeof(*ipu), GFP_KERNEL);
>> + if (!ipu)
>> + return -ENOMEM;
>> +
>> + soc_info = of_device_get_match_data(dev);
>> + if (!soc_info) {
>> + dev_err(dev, "Missing platform data\n");
>> + return -EINVAL;
>> + }
>> +
>> + ipu->dev = dev;
>> + ipu->master = master;
>> + ipu->soc_info = soc_info;
>> +
>> + base = devm_platform_ioremap_resource(pdev, 0);
>> + if (IS_ERR(base)) {
>> + dev_err(dev, "Failed to get memory resource\n");
>> + return PTR_ERR(base);
>> + }
>> +
>> + ipu->map = devm_regmap_init_mmio(dev, base,
>> &ingenic_ipu_regmap_config);
>> + if (IS_ERR(ipu->map)) {
>> + dev_err(dev, "Failed to create regmap\n");
>> + return PTR_ERR(ipu->map);
>> + }
>> +
>> + irq = platform_get_irq(pdev, 0);
>> + if (irq < 0)
>> + return irq;
>> +
>> + ipu->clk = devm_clk_get(dev, "ipu");
>> + if (IS_ERR(ipu->clk)) {
>> + dev_err(dev, "Failed to get pixel clock\n");
>> + return PTR_ERR(ipu->clk);
>> + }
>> +
>> + err = devm_request_irq(dev, irq, ingenic_ipu_irq_handler, 0,
>> + drm->driver->name, drm);
>> + if (err) {
>> + dev_err(dev, "Unable to request IRQ\n");
>> + return err;
>> + }
>> +
>> + plane = &ipu->plane;
>> + dev_set_drvdata(dev, plane);
>> +
>> + drm_plane_helper_add(plane, &ingenic_ipu_plane_helper_funcs);
>> +
>> + err = drm_universal_plane_init(drm, plane, 1,
>> &ingenic_ipu_plane_funcs,
>> + soc_info->formats, soc_info->num_formats,
>> + NULL, DRM_PLANE_TYPE_PRIMARY, NULL);
>> + if (err) {
>> + dev_err(dev, "Failed to init plane: %i\n", err);
>> + return err;
>> + }
>> +
>> + /*
>> + * Sharpness settings range is [0,32]
>> + * 0 : nearest-neighbor
>> + * 1 : bilinear
>> + * 2 .. 32 : bicubic (translated to sharpness factor -0.25 ..
>> -4.0)
>> + */
>> + sharpness_max = soc_info->has_bicubic ? 32 : 1;
>> + ipu->sharpness_prop = drm_property_create_range(drm, 0,
>> "sharpness",
>> + 0, sharpness_max);
>> + if (!ipu->sharpness_prop) {
>> + dev_err(dev, "Unable to create sharpness property\n");
>> + return -ENOMEM;
>> + }
>> +
>> + /* Default sharpness factor: -0.125 * 8 = -1.0 */
>> + ipu->sharpness = soc_info->has_bicubic ? 8 : 1;
>> + drm_object_attach_property(&plane->base, ipu->sharpness_prop,
>> + ipu->sharpness);
>> +
>> + err = clk_prepare_enable(ipu->clk);
>> + if (err) {
>> + dev_err(dev, "Unable to enable clock\n");
>> + return err;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void ingenic_ipu_unbind(struct device *dev,
>> + struct device *master, void *d)
>> +{
>> + struct ingenic_ipu *ipu = dev_get_drvdata(dev);
>> +
>> + clk_disable_unprepare(ipu->clk);
>> +}
>> +
>> +static const struct component_ops ingenic_ipu_ops = {
>> + .bind = ingenic_ipu_bind,
>> + .unbind = ingenic_ipu_unbind,
>> +};
>> +
>> +static int ingenic_ipu_probe(struct platform_device *pdev)
>> +{
>> + return component_add(&pdev->dev, &ingenic_ipu_ops);
>> +}
>> +
>> +static int ingenic_ipu_remove(struct platform_device *pdev)
>> +{
>> + component_del(&pdev->dev, &ingenic_ipu_ops);
>> + return 0;
>> +}
>> +
>> +static const u32 jz4725b_ipu_formats[] = {
>> + DRM_FORMAT_YUYV,
>> + DRM_FORMAT_YVYU,
>> + DRM_FORMAT_UYVY,
>> + DRM_FORMAT_VYUY,
>> + DRM_FORMAT_YUV411,
>> + DRM_FORMAT_YUV420,
>> + DRM_FORMAT_YUV422,
>> + DRM_FORMAT_YUV444,
>> +};
>> +
>> +static const struct soc_info jz4725b_soc_info = {
>> + .formats = jz4725b_ipu_formats,
>> + .num_formats = ARRAY_SIZE(jz4725b_ipu_formats),
>> + .has_bicubic = false,
>> + .set_coefs = jz4725b_set_coefs,
>> +};
>> +
>> +static const u32 jz4760_ipu_formats[] = {
>> + DRM_FORMAT_XRGB1555,
>> + DRM_FORMAT_XBGR1555,
>> + DRM_FORMAT_RGB565,
>> + DRM_FORMAT_BGR565,
>> + DRM_FORMAT_XRGB8888,
>> + DRM_FORMAT_XBGR8888,
>> + DRM_FORMAT_YUYV,
>> + DRM_FORMAT_YVYU,
>> + DRM_FORMAT_UYVY,
>> + DRM_FORMAT_VYUY,
>> + DRM_FORMAT_YUV411,
>> + DRM_FORMAT_YUV420,
>> + DRM_FORMAT_YUV422,
>> + DRM_FORMAT_YUV444,
>> +};
>> +
>> +static const struct soc_info jz4760_soc_info = {
>> + .formats = jz4760_ipu_formats,
>> + .num_formats = ARRAY_SIZE(jz4760_ipu_formats),
>> + .has_bicubic = true,
>> + .set_coefs = jz4760_set_coefs,
>> +};
>> +
>> +static const struct of_device_id ingenic_ipu_of_match[] = {
>> + { .compatible = "ingenic,jz4725b-ipu", .data = &jz4725b_soc_info
>> },
>> + { .compatible = "ingenic,jz4760-ipu", .data = &jz4760_soc_info },
>> + { /* sentinel */ },
>> +};
>> +MODULE_DEVICE_TABLE(of, ingenic_ipu_of_match);
>> +
>> +static struct platform_driver ingenic_ipu_driver = {
>> + .driver = {
>> + .name = "ingenic-ipu",
>> + .of_match_table = ingenic_ipu_of_match,
>> + },
>> + .probe = ingenic_ipu_probe,
>> + .remove = ingenic_ipu_remove,
>> +};
>> +
>> +struct platform_driver *ingenic_ipu_driver_ptr =
>> &ingenic_ipu_driver;
>> diff --git a/drivers/gpu/drm/ingenic/ingenic-ipu.h
>> b/drivers/gpu/drm/ingenic/ingenic-ipu.h
>> new file mode 100644
>> index 000000000000..eab6fab8c7f6
>> --- /dev/null
>> +++ b/drivers/gpu/drm/ingenic/ingenic-ipu.h
>> @@ -0,0 +1,109 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +//
>> +// Ingenic JZ47xx IPU - Register definitions and private API
>> +//
>> +// Copyright (C) 2020, Paul Cercueil <paul@crapouillou.net>
>> +
>> +#ifndef DRIVERS_GPU_DRM_INGENIC_INGENIC_IPU_H
>> +#define DRIVERS_GPU_DRM_INGENIC_INGENIC_IPU_H
>> +
>> +#include <linux/bitops.h>
>> +
>> +#define JZ_REG_IPU_CTRL 0x00
>> +#define JZ_REG_IPU_STATUS 0x04
>> +#define JZ_REG_IPU_D_FMT 0x08
>> +#define JZ_REG_IPU_Y_ADDR 0x0c
>> +#define JZ_REG_IPU_U_ADDR 0x10
>> +#define JZ_REG_IPU_V_ADDR 0x14
>> +#define JZ_REG_IPU_IN_GS 0x18
>> +#define JZ_REG_IPU_Y_STRIDE 0x1c
>> +#define JZ_REG_IPU_UV_STRIDE 0x20
>> +#define JZ_REG_IPU_OUT_ADDR 0x24
>> +#define JZ_REG_IPU_OUT_GS 0x28
>> +#define JZ_REG_IPU_OUT_STRIDE 0x2c
>> +#define JZ_REG_IPU_RSZ_COEF_INDEX 0x30
>> +#define JZ_REG_IPU_CSC_C0_COEF 0x34
>> +#define JZ_REG_IPU_CSC_C1_COEF 0x38
>> +#define JZ_REG_IPU_CSC_C2_COEF 0x3c
>> +#define JZ_REG_IPU_CSC_C3_COEF 0x40
>> +#define JZ_REG_IPU_CSC_C4_COEF 0x44
>> +#define JZ_REG_IPU_HRSZ_COEF_LUT 0x48
>> +#define JZ_REG_IPU_VRSZ_COEF_LUT 0x4c
>> +#define JZ_REG_IPU_CSC_OFFSET 0x50
>> +#define JZ_REG_IPU_Y_PHY_T_ADDR 0x54
>> +#define JZ_REG_IPU_U_PHY_T_ADDR 0x58
>> +#define JZ_REG_IPU_V_PHY_T_ADDR 0x5c
>> +#define JZ_REG_IPU_OUT_PHY_T_ADDR 0x60
>> +
>> +#define JZ_IPU_CTRL_ADDR_SEL BIT(20)
>> +#define JZ_IPU_CTRL_ZOOM_SEL BIT(18)
>> +#define JZ_IPU_CTRL_DFIX_SEL BIT(17)
>> +#define JZ_IPU_CTRL_LCDC_SEL BIT(11)
>> +#define JZ_IPU_CTRL_SPKG_SEL BIT(10)
>> +#define JZ_IPU_CTRL_VSCALE BIT(9)
>> +#define JZ_IPU_CTRL_HSCALE BIT(8)
>> +#define JZ_IPU_CTRL_STOP BIT(7)
>> +#define JZ_IPU_CTRL_RST BIT(6)
>> +#define JZ_IPU_CTRL_FM_IRQ_EN BIT(5)
>> +#define JZ_IPU_CTRL_CSC_EN BIT(4)
>> +#define JZ_IPU_CTRL_VRSZ_EN BIT(3)
>> +#define JZ_IPU_CTRL_HRSZ_EN BIT(2)
>> +#define JZ_IPU_CTRL_RUN BIT(1)
>> +#define JZ_IPU_CTRL_CHIP_EN BIT(0)
>> +
>> +#define JZ_IPU_STATUS_OUT_END BIT(0)
>> +
>> +#define JZ_IPU_IN_GS_H_LSB 0x0
>> +#define JZ_IPU_IN_GS_W_LSB 0x10
>> +#define JZ_IPU_OUT_GS_H_LSB 0x0
>> +#define JZ_IPU_OUT_GS_W_LSB 0x10
>> +
>> +#define JZ_IPU_Y_STRIDE_Y_LSB 0
>> +#define JZ_IPU_UV_STRIDE_U_LSB 16
>> +#define JZ_IPU_UV_STRIDE_V_LSB 0
>> +
>> +#define JZ_IPU_D_FMT_IN_FMT_LSB 0
>> +#define JZ_IPU_D_FMT_IN_FMT_RGB555 (0x0 << JZ_IPU_D_FMT_IN_FMT_LSB)
>> +#define JZ_IPU_D_FMT_IN_FMT_YUV420 (0x0 << JZ_IPU_D_FMT_IN_FMT_LSB)
>> +#define JZ_IPU_D_FMT_IN_FMT_YUV422 (0x1 << JZ_IPU_D_FMT_IN_FMT_LSB)
>> +#define JZ_IPU_D_FMT_IN_FMT_RGB888 (0x2 << JZ_IPU_D_FMT_IN_FMT_LSB)
>> +#define JZ_IPU_D_FMT_IN_FMT_YUV444 (0x2 << JZ_IPU_D_FMT_IN_FMT_LSB)
>> +#define JZ_IPU_D_FMT_IN_FMT_RGB565 (0x3 << JZ_IPU_D_FMT_IN_FMT_LSB)
>> +
>> +#define JZ_IPU_D_FMT_YUV_FMT_LSB 2
>> +#define JZ_IPU_D_FMT_YUV_Y1UY0V (0x0 << JZ_IPU_D_FMT_YUV_FMT_LSB)
>> +#define JZ_IPU_D_FMT_YUV_Y1VY0U (0x1 << JZ_IPU_D_FMT_YUV_FMT_LSB)
>> +#define JZ_IPU_D_FMT_YUV_UY1VY0 (0x2 << JZ_IPU_D_FMT_YUV_FMT_LSB)
>> +#define JZ_IPU_D_FMT_YUV_VY1UY0 (0x3 << JZ_IPU_D_FMT_YUV_FMT_LSB)
>> +#define JZ_IPU_D_FMT_IN_FMT_YUV411 (0x3 << JZ_IPU_D_FMT_IN_FMT_LSB)
>> +
>> +#define JZ_IPU_D_FMT_OUT_FMT_LSB 19
>> +#define JZ_IPU_D_FMT_OUT_FMT_RGB555 (0x0 <<
>> JZ_IPU_D_FMT_OUT_FMT_LSB)
>> +#define JZ_IPU_D_FMT_OUT_FMT_RGB565 (0x1 <<
>> JZ_IPU_D_FMT_OUT_FMT_LSB)
>> +#define JZ_IPU_D_FMT_OUT_FMT_RGB888 (0x2 <<
>> JZ_IPU_D_FMT_OUT_FMT_LSB)
>> +#define JZ_IPU_D_FMT_OUT_FMT_YUV422 (0x3 <<
>> JZ_IPU_D_FMT_OUT_FMT_LSB)
>> +#define JZ_IPU_D_FMT_OUT_FMT_RGBAAA (0x4 <<
>> JZ_IPU_D_FMT_OUT_FMT_LSB)
>> +
>> +#define JZ_IPU_D_FMT_RGB_OUT_OFT_LSB 22
>> +#define JZ_IPU_D_FMT_RGB_OUT_OFT_RGB (0x0 <<
>> JZ_IPU_D_FMT_RGB_OUT_OFT_LSB)
>> +#define JZ_IPU_D_FMT_RGB_OUT_OFT_RBG (0x1 <<
>> JZ_IPU_D_FMT_RGB_OUT_OFT_LSB)
>> +#define JZ_IPU_D_FMT_RGB_OUT_OFT_GBR (0x2 <<
>> JZ_IPU_D_FMT_RGB_OUT_OFT_LSB)
>> +#define JZ_IPU_D_FMT_RGB_OUT_OFT_GRB (0x3 <<
>> JZ_IPU_D_FMT_RGB_OUT_OFT_LSB)
>> +#define JZ_IPU_D_FMT_RGB_OUT_OFT_BRG (0x4 <<
>> JZ_IPU_D_FMT_RGB_OUT_OFT_LSB)
>> +#define JZ_IPU_D_FMT_RGB_OUT_OFT_BGR (0x5 <<
>> JZ_IPU_D_FMT_RGB_OUT_OFT_LSB)
>> +
>> +#define JZ4725B_IPU_RSZ_LUT_COEF_LSB 2
>> +#define JZ4725B_IPU_RSZ_LUT_COEF_MASK 0x7ff
>> +#define JZ4725B_IPU_RSZ_LUT_IN_EN BIT(1)
>> +#define JZ4725B_IPU_RSZ_LUT_OUT_EN BIT(0)
>> +
>> +#define JZ4760_IPU_RSZ_COEF20_LSB 6
>> +#define JZ4760_IPU_RSZ_COEF31_LSB 17
>> +#define JZ4760_IPU_RSZ_COEF_MASK 0x7ff
>> +#define JZ4760_IPU_RSZ_OFFSET_LSB 1
>> +#define JZ4760_IPU_RSZ_OFFSET_MASK 0x1f
>> +
>> +#define JZ_IPU_CSC_OFFSET_CHROMA_LSB 16
>> +#define JZ_IPU_CSC_OFFSET_LUMA_LSB 16
>> +
>> +#endif /* DRIVERS_GPU_DRM_INGENIC_INGENIC_IPU_H */
>> --
>> 2.27.0
>>
>> _______________________________________________
>> dri-devel mailing list
>> dri-devel@lists.freedesktop.org
>> https://lists.freedesktop.org/mailman/listinfo/dri-devel


\
 
 \ /
  Last update: 2020-06-30 15:34    [W:0.124 / U:0.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site