lkml.org 
[lkml]   [2020]   [Jun]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[v4] arm64: dts: sc7180: add nodes for idp display
Date
Add nodes for IDP display. The display is Visionox RM69299.

Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
---
Changes in v2:
- Adding dependency patchwork series
- Removing suspend configuration
- Adding blank before space curly brace
Changes in v3:
- Updating status for mdp and mdss node to get the
display working
- Change in commit text
Changes in v4:
- Added pinconf subnode
- Using macros for function and drive-strength

arch/arm64/boot/dts/qcom/sc7180-idp.dts | 65 +++++++++++++++++++++++++
1 file changed, 65 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 39dbfc89689e..5e0b7e4b2545 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -9,6 +9,7 @@

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include "sc7180.dtsi"
#include "pm6150.dtsi"
#include "pm6150l.dtsi"
@@ -287,6 +288,57 @@ vreg_bob: bob {
};
};

+&dsi0 {
+ status = "okay";
+
+ vdda-supply = <&vreg_l3c_1p2>;
+
+ panel@0 {
+ compatible = "visionox,rm69299-1080p-display";
+ reg = <0>;
+
+ vdda-supply = <&vreg_l8c_1p8>;
+ vdd3p3-supply = <&vreg_l18a_2p8>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&disp_pins>;
+
+ reset-gpios = <&pm6150l_gpio 3 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ panel0_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+ };
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&panel0_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+};
+
+&dsi_phy {
+ status = "okay";
+};
+
+&mdp {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
&qspi {
status = "okay";
pinctrl-names = "default";
@@ -402,6 +454,19 @@ wifi-firmware {

/* PINCTRL - additions to nodes defined in sc7180.dtsi */

+&pm6150l_gpio {
+ disp_pins: disp-pins {
+ pinconf {
+ pins = "gpio3";
+ function = PMIC_GPIO_FUNC_FUNC1;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_MED>;
+ power-source = <0>;
+ bias-disable;
+ output-low;
+ };
+ };
+};
+
&qspi_clk {
pinconf {
pins = "gpio63";
--
2.27.0
\
 
 \ /
  Last update: 2020-06-29 22:38    [W:0.060 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site