lkml.org 
[lkml]   [2020]   [Jun]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH] tty: serial: fsl_lpuart: minimum baud rate support
Date


> -----Original Message-----
> From: Greg KH <gregkh@linuxfoundation.org>
> Sent: Thursday, June 25, 2020 4:23 PM
> To: Vabhav Sharma (OSS) <vabhav.sharma@oss.nxp.com>
> Cc: jslaby@suse.com; linux-serial@vger.kernel.org; linux-
> kernel@vger.kernel.org; Varun Sethi <V.Sethi@nxp.com>
> Subject: Re: [PATCH] tty: serial: fsl_lpuart: minimum baud rate support
>
> On Thu, Jun 25, 2020 at 10:12:54AM +0000, Vabhav Sharma (OSS) wrote:
> >
> >
> > > -----Original Message-----
> > > From: Greg KH <gregkh@linuxfoundation.org>
> > > Sent: Thursday, June 25, 2020 3:34 PM
> > > To: Vabhav Sharma (OSS) <vabhav.sharma@oss.nxp.com>
> > > Cc: jslaby@suse.com; linux-serial@vger.kernel.org; linux-
> > > kernel@vger.kernel.org; Varun Sethi <V.Sethi@nxp.com>; Vabhav
> Sharma
> > > <vabhav.sharma@nxp.com>
> > > Subject: Re: [PATCH] tty: serial: fsl_lpuart: minimum baud rate
> > > support
> > >
> > > On Thu, Jun 25, 2020 at 03:19:05PM +0530, Vabhav Sharma wrote:
> > > > From: Vabhav Sharma <vabhav.sharma@nxp.com>
> > > >
> > > > The formula for the baud rate is
> > > > baud rate = "baud clock / ((OSR+1) × SBR)
> > > >
> > > > Algorithm used in function lpuart32_serial_setbrg() only changes
> > > > the SBR. Even with maxmum value put in, OSR stays at 0x7 and the
> > > > lowest baud rate would be ~ 2600 bps
> > > >
> > > > Update the algorithm to allow driver operation at 1200,2400 or
> > > > 600 bps
> > > >
> > > > Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
> > > > ---
> > > > drivers/tty/serial/fsl_lpuart.c | 4 ++++
> > > > 1 file changed, 4 insertions(+)
> > > >
> > > > diff --git a/drivers/tty/serial/fsl_lpuart.c
> > > > b/drivers/tty/serial/fsl_lpuart.c index 90298c4..0fd0fa5f 100644
> > > > --- a/drivers/tty/serial/fsl_lpuart.c
> > > > +++ b/drivers/tty/serial/fsl_lpuart.c
> > > > @@ -1925,6 +1925,10 @@ static void __lpuart32_serial_setbrg(struct
> > > uart_port *port,
> > > > tmp_sbr++;
> > > > }
> > > >
> > > > + if (tmp_sbr > UARTBAUD_SBR_MASK) {
> > > > + continue;
> > > > + }
> > >
> > > Always use scripts/checkpatch.pl on your patches so you do not get
> > > grumpy emails from maintainers telling you to use
> > > scripts/checkpatch.pl on your patches...
> > Indeed, I run the script before sending patch ./scripts/checkpatch.pl
> > 0001-tty-serial-fsl_lpuart-minimum-baud-rate-support.patch
> > total: 0 errors, 0 warnings, 10 lines checked
> >
> > 0001-tty-serial-fsl_lpuart-minimum-baud-rate-support.patch has no
> obvious style problems and is ready for submission.
>
> Ok, then something is wrong as there is obviously a coding style issue with
> your submission, as you can see with a manual review of it, right?
>
> greg k-h
I see, Unnecessary usage of brace for single statement.
Thank you

\
 
 \ /
  Last update: 2020-06-26 13:19    [W:1.382 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site