lkml.org 
[lkml]   [2020]   [Jun]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/3] phy: qcom-qmp: Allow different values for second lane
On Sat 23 May 19:14 PDT 2020, Jonathan Marek wrote:

> The primary USB PHY on sm8250 sets some values differently for the second
> lane. This makes it possible to represent that.
>
> Signed-off-by: Jonathan Marek <jonathan@marek.ca>
> ---
> drivers/phy/qualcomm/phy-qcom-qmp.c | 52 ++++++++++++++++++++++-------
> 1 file changed, 40 insertions(+), 12 deletions(-)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
> index e91040af3394..b3e07afca3ca 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
> @@ -82,20 +82,34 @@ struct qmp_phy_init_tbl {
> * register part of layout ?
> * if yes, then offset gives index in the reg-layout
> */
> - int in_layout;
> + bool in_layout;
> + /*
> + * mask of lanes for which this register is written
> + * for cases when second lane needs different values
> + */
> + u8 lane_mask;
> };
>
> #define QMP_PHY_INIT_CFG(o, v) \
> { \
> .offset = o, \
> .val = v, \
> + .lane_mask = 0xff, \
> }
>
> #define QMP_PHY_INIT_CFG_L(o, v) \
> { \
> .offset = o, \
> .val = v, \
> - .in_layout = 1, \
> + .in_layout = true, \
> + .lane_mask = 0xff, \
> + }
> +
> +#define QMP_PHY_INIT_CFG_LANE(o, v, l) \
> + { \
> + .offset = o, \
> + .val = v, \
> + .lane_mask = l, \
> }
>
> /* set of registers with offsets different per-PHY */
> @@ -1986,10 +2000,11 @@ static const struct qmp_phy_cfg sm8150_usb3phy_cfg = {
> .is_dual_lane_phy = true,
> };
>
> -static void qcom_qmp_phy_configure(void __iomem *base,
> - const unsigned int *regs,
> - const struct qmp_phy_init_tbl tbl[],
> - int num)
> +static void qcom_qmp_phy_configure_lane(void __iomem *base,
> + const unsigned int *regs,
> + const struct qmp_phy_init_tbl tbl[],
> + int num,
> + u8 lane_mask)
> {
> int i;
> const struct qmp_phy_init_tbl *t = tbl;
> @@ -1998,6 +2013,9 @@ static void qcom_qmp_phy_configure(void __iomem *base,
> return;
>
> for (i = 0; i < num; i++, t++) {
> + if (!(t->lane_mask & lane_mask))
> + continue;
> +
> if (t->in_layout)
> writel(t->val, base + regs[t->offset]);
> else
> @@ -2005,6 +2023,14 @@ static void qcom_qmp_phy_configure(void __iomem *base,
> }
> }
>
> +static void qcom_qmp_phy_configure(void __iomem *base,
> + const unsigned int *regs,
> + const struct qmp_phy_init_tbl tbl[],
> + int num)
> +{
> + qcom_qmp_phy_configure_lane(base, regs, tbl, num, 0xff);
> +}
> +
> static int qcom_qmp_phy_com_init(struct qmp_phy *qphy)
> {
> struct qcom_qmp *qmp = qphy->qmp;
> @@ -2219,16 +2245,18 @@ static int qcom_qmp_phy_enable(struct phy *phy)
> }
>
> /* Tx, Rx, and PCS configurations */
> - qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
> + qcom_qmp_phy_configure_lane(tx, cfg->regs,
> + cfg->tx_tbl, cfg->tx_tbl_num, 1);

Please ignore the 80-char suggestion and keep this on one line.

With that...
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Regards,
Bjorn

> /* Configuration for other LANE for USB-DP combo PHY */
> if (cfg->is_dual_lane_phy)
> - qcom_qmp_phy_configure(qphy->tx2, cfg->regs,
> - cfg->tx_tbl, cfg->tx_tbl_num);
> + qcom_qmp_phy_configure_lane(qphy->tx2, cfg->regs,
> + cfg->tx_tbl, cfg->tx_tbl_num, 2);
>
> - qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
> + qcom_qmp_phy_configure_lane(rx, cfg->regs,
> + cfg->rx_tbl, cfg->rx_tbl_num, 1);
> if (cfg->is_dual_lane_phy)
> - qcom_qmp_phy_configure(qphy->rx2, cfg->regs,
> - cfg->rx_tbl, cfg->rx_tbl_num);
> + qcom_qmp_phy_configure_lane(qphy->rx2, cfg->regs,
> + cfg->rx_tbl, cfg->rx_tbl_num, 2);
>
> qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
> ret = reset_control_deassert(qmp->ufs_reset);
> --
> 2.26.1
>

\
 
 \ /
  Last update: 2020-06-26 09:39    [W:0.095 / U:0.692 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site