lkml.org 
[lkml]   [2020]   [Jun]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 03/11] arm64: dts: renesas: hihope-common: Separate out Rev.2.0 specific into hihope-common-rev2.dtsi file
Hi Geert,

On Mon, Jun 8, 2020 at 3:59 PM Lad, Prabhakar
<prabhakar.csengg@gmail.com> wrote:
>
> Hi Geert,
>
> On Mon, Jun 8, 2020 at 3:47 PM Geert Uytterhoeven <geert@linux-m68k.org> wrote:
> >
> > Hi Prabhakar,
> >
> > On Sun, Jun 7, 2020 at 8:41 PM Lad Prabhakar
> > <prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> > > Separate out Rev.2.0 specific hardware changes into
> > > hihope-common-rev2.dtsi file so that hihope-common.dtsi can be used
> > > by all the variants for RZ/G2M[N] boards.
> > >
> > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > > Reviewed-by: Marian-Cristian Rotariu <marian-cristian.rotariu.rb@bp.renesas.com>
> >
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/renesas/hihope-common-rev2.dtsi
> >
> > Perhaps just hihope-rev2.dtsi, i.e. without the "common-"?
> >
> Yes makes sense.
>
> > > @@ -0,0 +1,101 @@
> > > +// SPDX-License-Identifier: GPL-2.0
> > > +/*
> > > + * Device Tree Source for the HiHope RZ/G2[MN] main board Rev.2.0 common
> > > + * parts
> > > + *
> > > + * Copyright (C) 2020 Renesas Electronics Corp.
> > > + */
> > > +
> > > +#include <dt-bindings/gpio/gpio.h>
> > > +
> > > +/ {
> > > + leds {
> > > + compatible = "gpio-leds";
> > > +
> > > + bt_active_led {
> > > + label = "blue:bt";
> > > + gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
> > > + linux,default-trigger = "hci0-power";
> > > + default-state = "off";
> > > + };
> > > +
> > > + led0 {
> > > + gpios = <&gpio6 11 GPIO_ACTIVE_HIGH>;
> > > + };
> > > +
> > > + led1 {
> > > + gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
> > > + };
> > > +
> > > + led2 {
> > > + gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
> > > + };
> > > +
> > > + led3 {
> > > + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
> > > + };
> >
> > led1, led2, and led3 are present on both, so I'd keep them in
> > hihope-common.dtsi.
> >
> The leds defined in hihope-common-rev4.dtsi are as per the label names
> on the schematics/board so that it's easier to identify the LED's by
> name.
>
I was waiting on the above to be confirmed.

Cheers,
--Prabhakar

> > > +
> > > + wlan_active_led {
> > > + label = "yellow:wlan";
> > > + gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
> > > + linux,default-trigger = "phy0tx";
> > > + default-state = "off";
> > > + };
> > > + };
> > > +
> > > + wlan_en_reg: regulator-wlan_en {
> > > + compatible = "regulator-fixed";
> > > + regulator-name = "wlan-en-regulator";
> > > + regulator-min-microvolt = <1800000>;
> > > + regulator-max-microvolt = <1800000>;
> > > + startup-delay-us = <70000>;
> > > +
> > > + gpio = <&gpio_expander 1 GPIO_ACTIVE_HIGH>;
> > > + enable-active-high;
> > > + };
> >
> > Same for the WLAN regulator, especially as it is referenced from
> > hihope-common.dtsi.
> > As the GPIO line differs between the two variants, you just need
> > to add the gpio property in the revision-specific file.
> >
> Agreed will move this to common.
>
> > > +};
> > > +
> > > +&hscif0 {
> > > + bluetooth {
> > > + compatible = "ti,wl1837-st";
> > > + enable-gpios = <&gpio_expander 2 GPIO_ACTIVE_HIGH>;
> > > + };
> > > +};
> >
> > As node is small, and the GPIO line differs from the two variants,
> > I think duplicating it in both revision-specific files is fine, though.
> >
> Agreed.
>
> Cheers,
> --Prabhakar
>
> > Gr{oetje,eeting}s,
> >
> > Geert
> >
> > --
> > Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
> >
> > In personal conversations with technical people, I call myself a hacker. But
> > when I'm talking to journalists I just say "programmer" or something like that.
> > -- Linus Torvalds

\
 
 \ /
  Last update: 2020-06-23 09:52    [W:0.057 / U:0.644 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site