lkml.org 
[lkml]   [2020]   [Jun]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH v2 0/2] cpufreq: Specify the default governor on command line
Date
On 2020.06.23 07:22 Quentin Perret wrote:
>
> This series enables users of prebuilt kernels (e.g. distro kernels) to
> specify their CPUfreq governor of choice using the kernel command line,
> instead of having to wait for the system to fully boot to userspace to
> switch using the sysfs interface. This is helpful for 2 reasons:
> 1. users get to choose the governor that runs during the actual boot;
> 2. it simplifies the userspace boot procedure a bit (one less thing to
> worry about).
>
> To enable this, the first patch moves all governor init calls to
> core_initcall, to make sure they are registered by the time the drivers
> probe. This should be relatively low impact as registering a governor
> is a simple procedure (it gets added to a llist), and all governors
> already load at core_initcall anyway when they're set as the default
> in Kconfig. This also allows to clean-up the governors' init/exit code,
> and reduces boilerplate.
>
> The second patch introduces the new command line parameter, inspired by
> its cpuidle counterpart. More details can be found in the respective
> patch headers.
>
> Changes in v2:
> - added Viresh's ack to patch 01
> - moved the assignment of 'default_governor' in patch 02 to the governor
> registration path instead of the driver registration (Viresh)
>
> Thanks,
> Quentin
>
> Quentin Perret (2):
> cpufreq: Register governors at core_initcall
> cpufreq: Specify default governor on command line
>
> .../admin-guide/kernel-parameters.txt | 5 ++++
> Documentation/admin-guide/pm/cpufreq.rst | 6 ++---
> .../platforms/cell/cpufreq_spudemand.c | 26 ++-----------------
> drivers/cpufreq/cpufreq.c | 23 ++++++++++++----
> drivers/cpufreq/cpufreq_conservative.c | 22 ++++------------
> drivers/cpufreq/cpufreq_ondemand.c | 24 +++++------------
> drivers/cpufreq/cpufreq_performance.c | 14 ++--------
> drivers/cpufreq/cpufreq_powersave.c | 18 +++----------
> drivers/cpufreq/cpufreq_userspace.c | 18 +++----------
> include/linux/cpufreq.h | 14 ++++++++++
> kernel/sched/cpufreq_schedutil.c | 6 +----
> 11 files changed, 62 insertions(+), 114 deletions(-)
>
> --
> 2.27.0.111.gc72c7da667-goog

Hi Quentin,

Because I am lazy and sometimes do not want to recompile
the distro source, I have a need/desire for this.

Tested these two grub command lines:

GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 consoleblank=300 intel_pstate=disable cpufreq.default_governor=schedutil cpuidle_sysfs_switch cpuidle.governor=teo"

And

#GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 consoleblank=450 intel_pstate=passive cpufreq.default_governor=schedutil cpuidle_sysfs_switch cpuidle.governor=teo"

And all worked as expected. I use Ubuntu as my distro, and also had to disable a startup script that switches to "ondemand", or similar, after 1 minute.

As a side note (separate subject, but is one reason I tried it):
My i5-9600K based computer seems to hit a power limit during boot approximately 3 seconds after kernel selection on grub.
This had no effect on that issue (even when selecting powersave governor).

... Doug


\
 
 \ /
  Last update: 2020-06-23 19:55    [W:0.147 / U:0.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site