lkml.org 
[lkml]   [2020]   [Jun]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH] serial: 8250_port: Fix imprecise external abort for mctrl if inactive
* Tony Lindgren <tony@atomide.com> [200602 13:38]:
> * Andy Shevchenko <andy.shevchenko@gmail.com> [200602 08:33]:
> Now that we can detach and reattach the kernel serial console,
> there should not be any need for pm_runtime_irq_safe() anymore :)

Below is a hastily tested RFC patch to remove pm_runtime_irq_safe()
for 8250_omap.c that seems to work for idle use case :)

> And the UART wake-up from deeper idle states can only happen with
> help of external hardware like GPIO controller or pinctrl controller.

It does not yet include the check for configured wakeirq though.
And omap-serial.c needs a similar patch or maybe we can attempt
to just drop it this time as 8250_omap.c should be used nowadays.
Or just drop PM from omap-serial.c if it can't be dropped.

Andy, is the change below the only remaining blocker now for
your serial PM runtime changes?

Regards,

Tony

8< -------------------------------
diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c
--- a/drivers/tty/serial/8250/8250_omap.c
+++ b/drivers/tty/serial/8250/8250_omap.c
@@ -123,6 +123,7 @@ struct omap8250_priv {
spinlock_t rx_dma_lock;
bool rx_dma_broken;
bool throttled;
+ unsigned int active:1;
};

struct omap8250_dma_params {
@@ -598,9 +599,13 @@ static irqreturn_t omap8250_irq(int irq, void *dev_id)
{
struct uart_port *port = dev_id;
struct uart_8250_port *up = up_to_u8250p(port);
+ struct omap8250_priv *priv = up->port.private_data;
unsigned int iir;
int ret;

+ if (!priv->active)
+ return IRQ_NONE;
+
#ifdef CONFIG_SERIAL_8250_DMA
if (up->dma) {
ret = omap_8250_dma_handle_irq(port);
@@ -608,10 +613,10 @@ static irqreturn_t omap8250_irq(int irq, void *dev_id)
}
#endif

- serial8250_rpm_get(up);
iir = serial_port_in(port, UART_IIR);
ret = serial8250_handle_irq(port, iir);
- serial8250_rpm_put(up);
+
+ pm_runtime_mark_last_busy(port->dev);

return IRQ_RETVAL(ret);
}
@@ -1110,13 +1115,9 @@ static int omap_8250_dma_handle_irq(struct uart_port *port)
unsigned long flags;
u8 iir;

- serial8250_rpm_get(up);
-
iir = serial_port_in(port, UART_IIR);
- if (iir & UART_IIR_NO_INT) {
- serial8250_rpm_put(up);
+ if (iir & UART_IIR_NO_INT)
return IRQ_HANDLED;
- }

spin_lock_irqsave(&port->lock, flags);

@@ -1144,7 +1145,7 @@ static int omap_8250_dma_handle_irq(struct uart_port *port)
}

uart_unlock_and_check_sysrq(port, flags);
- serial8250_rpm_put(up);
+
return 1;
}

@@ -1329,11 +1330,10 @@ static int omap8250_probe(struct platform_device *pdev)
if (!of_get_available_child_count(pdev->dev.of_node))
pm_runtime_set_autosuspend_delay(&pdev->dev, -1);

- pm_runtime_irq_safe(&pdev->dev);
-
pm_runtime_get_sync(&pdev->dev);

omap_serial_fill_features_erratas(&up, priv);
+ priv->active = pm_runtime_enabled(&pdev->dev);
up.port.handle_irq = omap8250_no_handle_irq;
priv->rx_trigger = RX_TRIGGER;
priv->tx_trigger = TX_TRIGGER;
@@ -1517,6 +1517,8 @@ static int omap8250_runtime_suspend(struct device *dev)
if (!priv)
return 0;

+ priv->active = 0;
+
up = serial8250_get_port(priv->line);
/*
* When using 'no_console_suspend', the console UART must not be
@@ -1575,6 +1577,8 @@ static int omap8250_runtime_resume(struct device *dev)

pinctrl_pm_select_default_state(dev);

+ priv->active = 1;
+
return 0;
}
#endif
--
2.26.2
\
 
 \ /
  Last update: 2020-06-02 20:56    [W:1.602 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site